journal article·2013-03Open access

Scalability and stability of very thin, roll-to-roll processed, large area, indium-tin-oxide free polymer solar cell modules

Dechan Angmo, Suren A. Gevorgyan, Thue. T. Larsen-Olsen, Roar R. Søndergaard, Markus Hösel, Mikkel Jørgensen, Ritu Gupta, Giridhar U. Kulkarni, Frederik C. Krebs

Organic Electronics· Volume 14· Issue 3

Abstract

Polymer solar cell modules were prepared directly on thin flexible barrier polyethylene terephthalate foil. The performance of the modules was found to be scalable from a single cell with an area of 6 cm 2 to modules with a total area of up to 186 cm 2. The substrate thickness was also explored and the performance was found to be independent of thickness in the range of 20–130 μm. The thinner substrates were found to present some challenge regarding handling but were not limited in performance. Large area modules on a substrate thickness of 45 μm were finally prepared by full roll-to-roll processing employing P3HT:PCBM as the active material and were found to exhibit a total area efficiency of >1% (1000 W/m −2; AM1.5G) with a typical active-area efficiency in the 1.5–1.6% for total module area of >110 cm 2 due to high fill factors in excess of 50%. The modules were also found to have an active-area efficiency of >1% under low light levels (∼100 W m −2). The modules were then subjected to extensive stability testing for a minimum of 1000 h employing several ISOS protocols. The modules presented higher than 80% of the initial performance ( T80) in the dark (ISOS-D-1), in dark under elevated temperature of 65 °C (ISOS-D-2), under low light (ISOS-LL), under full sunlight (ISOS-L-2), and under outdoor testing (ISOS-O), which was conducted in two locations in India and Denmark. We estimate maximum T80 for those tests to be 2800, 5000, 1300, 1000, and 3500 h respectively. The modules showed significant sensitivity to high humidity and had low values for T80 for dark storage tests at 50 °C/85%RH (ISOS-D-3) and accelerated operation conditions with 0.7 sun/65 oC/50%RH (ISOS-L-3). We found the modules to be particularly suited for information and communications technology (ICT) and mobile applications where low humidity (<50%) and lower temperatures (<65 °C) can be anticipated and we estimate operational lifetimes in excess of 1 year.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Thin-Film Transistor Technologies · Silicon and Solar Cell Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. A life cycle analysis of polymer solar cell modules prepared using roll-to-roll methods under ambient conditions10.1016/j.solmat.2010.08.020 ↗
2. Efficient and flexible ITO-free organic solar cells using highly conductive polymer anodes10.1002/adma.200800338 ↗
3. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
4. Degradation mechanisms in organic photovoltaic devices10.1016/j.orgel.2011.11.027 ↗
5. Consensus stability testing protocols for organic photovoltaic materials and devices10.1016/j.solmat.2011.01.036 ↗
6. Upscaling of polymer solar cell fabrication using full roll-to-roll processing10.1039/b9nr00430k ↗
7. All solution processing of ITO-free organic solar cell modules directly on barrier foil10.1016/j.solmat.2012.07.004 ↗
8. Electrical and optical properties of ZnO processed by atomic layer deposition in inverted polymer solar cells10.1021/jp106641j ↗
9. Electronic memory effects in diodes from a zinc oxide nanoparticle-polystyrene hybrid material10.1063/1.2345612 ↗
10. Silver front electrode grids for ITO-free all printed polymer solar cells with embedded and raised topographies, prepared by thermal imprint, flexographic and inkjet roll-to-roll processes10.1039/c2nr31508d ↗
11. Variations of cell performance in ITO-free organic solar cells with increasing cell areas10.1088/0268-1242/26/3/034010 ↗
12. A roll-to-roll process to flexible polymer solar cells: model studies, manufacture and operational stability studies10.1039/b823001c ↗
13. Influence of cathode oxidation via the hole extraction layer in polymer: fullerene solar cells10.1016/j.orgel.2011.01.025 ↗
14. Degradation patterns in water and oxygen of an inverted polymer solar cell10.1021/ja106299g ↗
15. Mechanisms of vapor permeation through multilayer barrier films: lag time versus equilibrium permeation10.1063/1.1768610 ↗