High speed pulsed laser cutting of anode material for a Li-ion battery in burst mode
Source abstract
Abstract
The bursts of picosecond laser pulses have nanosecond-level short interval delay. These bursts contain a variable number of sub-pulses, which are used for laser cutting of copper current collector and graphite anode material for Li-ion battery anode. The influences of 2–10 sub-pulses on kerf edges were studied and were compared with that of a single pulse. The shapes of anode edge cut under different conditions, obtained using scanning electron microscopy (SEM), revealed that using burst mode would yield a smaller heat-affected zone (HAZ) of the copper current collector and smaller delamination width of graphite anode material. The capability of laser cutting of anode was characterized with maximum single-time cutting speed. Results showed that the cutting efficiency was raised evidently with the increase in the number of pulses in a burst, and the maximum cutting speeds for the copper current collector and graphite anode material could reach 3,800 mm/s and 500 mm/s respectively.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Integrated Circuits and Semiconductor Failure Analysis · Semiconductor materials and devices · Electron and X-Ray Spectroscopy Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Guangdong Ocean University
Foshan University
Funding
National Natural Science Foundation of China
References (23)
Show source-provided references
1. Chung · Nat. Mater. · 2002 · 1 · 12310.1038/nmat732 ↗
2. Dudney · Mater. Sci. Eng., B · 2005 · 116 · 24510.1016/j.mseb.2004.05.045 ↗
3. Sasaki · Nat. Mater. · 2013 · 12 · 56910.1038/nmat3623 ↗
4. Yancheng · J. Power Sources · 2011 · 196 · 151310.1016/j.jpowsour.2010.08.070 ↗
5. Li · J. Manuf. Syst. · 2011 · 30 · 18810.1016/j.jmsy.2011.07.009 ↗
6. Kronthaler · Phys. Procedia · 2012 · 39 · 21310.1016/j.phpro.2012.10.032 ↗
7. Ou · J. Phys. Chem. Solids · 2019 · 134 · 1410.1016/j.jpcs.2019.05.033 ↗
8. Luetke · Phys. Procedia · 2011 · 12 · 28610.1016/j.phpro.2011.03.135 ↗
9. Lee · J. Power Sources · 2012 · 210 · 32710.1016/j.jpowsour.2012.03.030 ↗
10. Lee · J. Power Sources · 2013 · 240 · 36810.1016/j.jpowsour.2012.10.096 ↗
11. Lutey · Opt. Laser Technol. · 2015 · 65 · 16410.1016/j.optlastec.2014.07.023 ↗
12. Zhang · Opt. Laser Eng. · 2019 · 118 · 1410.1016/j.optlaseng.2019.01.013 ↗
13. Schmieder · Proc. SPIE · 2015 · 9351 · 93511C10.1117/12.2086719 ↗
14. Lutey · Opt. Laser Technol. · 2017 · 94 · 9010.1016/j.optlastec.2017.03.022 ↗
15. Pfleging · Proc. SPIE · 2016 · 9740 · 97401310.1117/12.2212041 ↗
16. Can · Nature · 2016 · 537 · 8410.1038/nature18619 ↗
17. Giannuzzi · Opt. Laser Eng. · 2019 · 114 · 1510.1016/j.optlaseng.2018.10.006 ↗
18. Caterina · Opt. Express · 2018 · 26 · 380110.1364/OE.26.003801 ↗
19. Saeid · Opt. Lett. · 2015 · 40 · 206410.1364/OL.40.002064 ↗
20. Domke · Appl. Surf. Sci. · 2020 · 505 · 14459410.1016/j.apsusc.2019.144594 ↗
21. Butkus · Micromachines · 2020 · 11 · 73310.3390/mi11080733 ↗
22. Metzner · Appl. Surf. Sci. · 2020 · 531 · 14727010.1016/j.apsusc.2020.147270 ↗
23. Förster · Appl. Surf. Sci. · 2020 · 510 · 14539110.1016/j.apsusc.2020.145391 ↗