Shifting up the optimum figure of merit of p-type bismuth telluride-based thermoelectric materials for power generation by suppressing intrinsic conduction
Source abstract
Abstract
The abundance of low-temperature waste heat produced by industry and automobile exhaust necessitates the development of power generation with thermoelectric (TE) materials. Commercially available bismuth telluride-based alloys are generally used near room temperature. Materials that are composed of p-type bismuth telluride, which are suitable for low-temperature power generation (near 380 K), were successfully obtained through Sb-alloying, which suppresses detrimental intrinsic conduction at elevated temperatures by increasing hole concentrations and material band gaps. Furthermore, hot deformation (HD)-induced multi-scale microstructures were successfully realized in the high-performance p-type TE materials. Enhanced textures and donor-like effects all contributed to improved electrical transport properties. Multiple phonon scattering centers, including local nanostructures induced by dynamic recrystallization and high-density lattice defects, significantly reduced the lattice thermal conductivity. These combined effects resulted in observable improvement of ZT over the entire temperature range, with all TE parameters measured along the in-plane direction. The maximum ZT of 1.3 for the hot-deformed Bi0.3Sb1.7Te3 alloy was reached at 380 K, whereas the average ZTav of 1.18 was found in the range of 300–480 K, indicating potential for application in low-temperature TE power generation. Thermoelectric materials, which convert temperature differences and electric voltage into each other, serve in refrigeration or power generation applications. Currently, bismuth telluride (Bi2Te3) and its alloys are the most widely used thermoelectric materials. Tie-Jun Zhu, Xin-Bing Zhao and co-workers from Zhejiang University, China, have now investigated the effect of antimony (Sb) alloying on bismuth tellurides through a series of polycrystalline solid solutions of Bi2-xSbxTe3—where x varies between 1.4 and 1.8—prepared by hot deformation. Systematic tuning of the alloy composition showed that higher antimony content raised the material's optimal conversion temperature by repressing undesirable conduction. This effect arises from an increase in both the hole concentration and the band gap in the material. For a composition where x is 1.7, the alloy showed optimal performances at 380 kelvin—a suitable temperature for low-temperature power generation from the waste heat generated by industry or vehicles. The p-type bismuth telluride-based polycrystalline materials suiting for low-temperature power generations (near 380 K) have been obtained through Sb-alloying and HD, which suppresses the detrimental effect of intrinsic conduction at elevated temperature via increasing the hole concentration and band gap. The hot-deformed Bi0.3Sb1.7Te3 alloy, not usual composition Bi0.5Sb1.5Te3, shows a maximum ZT of 1.3 at 380 K, indicating a bright application potential in low-temperature power generations.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal properties of materials · Thermal Radiation and Cooling Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. DiSalvo, F. J. Thermoelectric cooling and power generation. Science 285, 703–706 (1999).10.1126/science.285.5428.703 ↗
2. Zhao, X. B., Ji, X. H., Zhang, Y. H., Zhu, T. J., Tu, J. P. & Zhang, X. B. Bismuth telluride nanotubes and the effects on the thermoelectric properties of nanotube-containing nanocomposites. Appl. Phys. Lett. 86, 062111 (2005).10.1063/1.1863440 ↗
3. Dresselhaus, M. S., Chen, G., Tang, M. Y., Yang, R. G., Lee, H., Wang, D. Z., Ren, Z. F., Fleurial, J. P. & Gogna, P. New directions for low-dimensional thermoelectric materials. Adv. Mater. 19, 1043–1053 (2007).10.1002/adma.200600527 ↗
4. Tang, X. F., Xie, W. J., Li, H., Zhao, W. Y., Zhang, Q. J. & Niino, M. Preparation and thermoelectric transport properties of high-performance p-type Bi2Te3 with layered nanostructure. Appl. Phys. Lett. 90, 012102 (2007).10.1063/1.2425007 ↗
5. Cao, Y. Q., Zhao, X. B., Zhu, T. J., Zhang, X. B. & Tu, J. P. Syntheses and thermoelectric properties of Bi2Te3/Sb2Te3 bulk nanocomposites with laminated nanostructure. Appl. Phys. Lett. 92, 143106 (2008).10.1063/1.2900960 ↗
6. Poudel, B., Hao, Q., Ma, Y., Lan, Y. C., Minnich, A., Yu, B., Yan, X., Wang, D. Z., Muto, A., Vashaee, D., Chen, X. Y., Liu, J. M., Dresselhaus, M. S., Chen, G. & Ren, Z. F. High-thermoelectric performance of nanostructured bismuth antimony telluride bulk alloys. Science 320, 634–638 (2008).10.1126/science.1156446 ↗
7. Shen, J. J., Zhu, T. J., Zhao, X. B., Zhang, S. N., Yang, S. H. & Yin, Z. Z. Recrystallization induced in situ nanostructures in bulk bismuth antimony tellurides: a simple top down route and improved thermoelectric properties. Energy Environ. Sci. 3, 1519–1523 (2010).10.1039/c0ee00012d ↗
8. Mehta, R. J., Zhang, Y. L., Karthik, C., Singh, B., Siegel, R. W., Tasciuc, T. B. & Ramanath, G. A new class of doped nanobulk high-figure-of-merit thermoelectrics by scalable bottom-up assembly. Nature Mater. 11, 233–240 (2012).10.1038/nmat3213 ↗
9. Li, J. F., Liu, W. S., Zhao, L. D. & Zhou, M. High-performance nanostructured thermoelectric materials. NPG Asia Mater 2, 152–158 (2010).10.1038/asiamat.2010.138 ↗
10. Heremans, J. P., Jovovic, V., Toberer, E. S., Saramat, A., Kurosaki, K., Charoenphakdee, A., Yamanaka, S. & Snyder, G. J. Enhancement of thermoelectric efficiency in PbTe by distortion of the electronic density of states. Science 321, 554–557 (2008).10.1126/science.1159725 ↗
11. Pei, Y., Shi, X., LaLonde, A., Wang, H., Chen, L. & Snyder, G. J. Convergence of electronic bands for high performance bulk thermoelectrics. Nature 473, 66–69 (2011).10.1038/nature09996 ↗
12. Pei, Y. Z., Wang, H., Gibbs, Z. M., LaLonde, A. D. & Snyder, J. G. Thermopower enhancement in Pb1-xMnxTe alloys and its effect on thermoelectric efficiency. NPG Asia Mater. 4, e28 (2012).10.1038/am.2012.52 ↗
13. Liu, W., Tan, X. J., Yin, K., Liu, H. J., Tang, X. F., Shi, J., Zhang, Q. J. & Uher, C. Convergence of conduction bands as a means of enhancing thermoelectric performance of n-type Mg2Si1−xSnx solid solutions. Phys. Rev. Lett. 108, 166601 (2012).10.1103/PhysRevLett.108.166601 ↗
14. Zhang, Q., Cao, F., Liu, W. S., Lucas, K., Yu, B., Chen, S., Opeil, C., Broido, D., Chen, G. & Ren, Z. F. Heavy doping and band engineering by potassium to improve the thermoelectric figure of merit in p-type PbTe, PbSe, and PbTe1– ySey . J. Am. Chem. Soc 134, 10031–10038 (2012).10.1021/ja301245b ↗
15. Jiang, J., Chen, L. D., Yao, Q., Bai, S. Q. & Wang, Q. Effect of TeI4 content on the thermoelectric properties of n-type Bi-Te-Se crystals prepared by zone melting. Mater. Chem. Phys. 92, 39–42 (2005).10.1016/j.matchemphys.2004.12.028 ↗
16. Yamashita, O., Tomiyoshi, S. & Makita, K. J. Bismuth telluride compounds with high thermoelectric figures of merit. Appl. Phys. 93, 368–374 (2003).10.1063/1.1525400 ↗
17. Zemskov, V. S., Belaya, A. D., Beluy, U. S. & Kozhemyakin, G. N. J. Growth and investigation of thermoelectric properties of Bi-Sb alloy single crystals. Cryst. Growth 212, 161–166 (2000).10.1016/S0022-0248(99)00587-4 ↗
18. Ma, Y., Hao, Q., Poudel, B., Lan, Y. C., Yu, B., Wang, D. Z., Chen, G. & Ren, Z. F. Enhanced thermoelectric figure-of-merit in p-type nanostructured bismuth antimony tellurium slloys made from elemental chunks. Nano Lett. 8, 2580–2584 (2008).10.1021/nl8009928 ↗
19. Liu, W. S., Lucas, K. C., McEnaney, K., Li, S., Zhang, Q., Opeil, C. P., Chen, G. & Ren, Z. F. Studies on the Bi2Te3-Bi2Se3-Bi2S3 system for mid-temperature thermoelectric energy conversion. Energy Environ. Sci. 6, 552–560 (2013).10.1039/C2EE23549H ↗
20. Xie, W. J., Tang, X. F., Yan, Y. G., Zhang, Q. J. & Tritt, T. M. Unique nanostructures and enhanced thermoelectric performance of melt-spun BiSbTe alloys. Appl. Phys. Lett 94, 102111 (2009).10.1063/1.3097026 ↗
21. Shen, J. J., Yin, Z. Z., Yang, S. H., Yu, C., Zhu, T. J. & Zhao, X. B. Improved thermoelectric performance of p-type bismuth antimony telluride bulk alloys prepared by Hot Forging. J. Electron. Mater. 40, 1095–1099 (2011).10.1007/s11664-011-1549-5 ↗
22. Hu, L. P., Gao, H. L., Liu, X. H., Xie, H. H., Shen, J. J., Zhu, T. J. & Zhao, X. B. Enhancement in thermoelectric performance of bismuth telluride based alloys by multi-scale microstructural effects. J. Mater. Chem. 22, 16484–16490 (2012).10.1039/c2jm32916f ↗
23. Hu, L. P., Liu, X. H., Xie, H. H., Shen, J. J., Zhu, T. J. & Zhao, X. B. Improving thermoelectric properties of n-type bismuth–telluride-based alloys by deformation-induced lattice defects and texture enhancement. Acta Mater. 60, 4431–4437 (2012).10.1016/j.actamat.2012.05.008 ↗
24. Yim, W. M. & Rosi, F. D. Compound tellurides and their alloys for peltier cooling. Solid-State Electron. 15, 1121–1140 (1972).10.1016/0038-1101(72)90172-4 ↗
25. Miller, G. R. & Li, C. Y. Evidence for the existence of antistructure defects in bismuth telluride by density measurements. J. Phys. Chem. Solids 26, 173–177 (1965).10.1016/0022-3697(65)90084-3 ↗
26. Horak, J., Cermak, K. & Koudelka, L. Energy formation of antisite defects in doped Sb2Te3 and Bi2Te3 crystals. J. Phys. Chem. Solids 47, 805–809 (1986).10.1016/0022-3697(86)90010-7 ↗
27. Stary, Z., Horak, J., Stordeur, M. & Stolzer, M. Antisite defects in Sb2- xBixTe3 mixed crystals. J. Phys. Chem. Solids 49, 29–34 (1988).10.1016/0022-3697(88)90130-8 ↗
28. Navratil, J., Stary, Z. & Plechacek, T. Thermoelectric properties of p-type antimony bismuth telluride alloys prepared by cold pressing. Mater. Res. Bull 31, 1559–1566 (1996).10.1016/S0025-5408(96)00149-3 ↗
29. Oh, T. S., Hyun, D. B. & Kolomoets, N. V. Thermoelectric properties of the hot-pressed (Bi,Sb)2(Te,Se)3 alloys. Scripta Mater. 42, 849–854 (2000).10.1016/S1359-6462(00)00302-X ↗
30. Austin, I. G. The optical properties of bismuth telluride. Proc. Phys. Soc. Lond. 72, 545–552 (1958).10.1088/0370-1328/72/4/309 ↗
31. Black, J., Conwell, E. M., Seigle, L. & Spencer, C. W. Electrical and optical properties of some M2V-BN3VI-B semiconductors. J. Phys. Chem. Solids 2, 240–251 (1957).10.1016/0022-3697(57)90090-2 ↗
32. Kohler, H. Non-parabolicity of highest valence band of Bi2Te3 from Shubnikov-Dehaas effect. Phys. Status. Solidi. B 74, 591–600 (1976).10.1002/pssb.2220740218 ↗
33. Kohler, H. Non-parabplic E(K) relation of lowest conduction-band in Bi2Te3 . Phys. Status Solidi. B 73, 95–104 (1976).10.1002/pssb.2220730107 ↗
34. Langhammer, H. T., Stordeur, M., Sobotta, H. & Riede, V. Ir transmission investigations of Sb2Te3 single-crystals. Phys. Status Solidi. B 123, K47–K51 (1984).10.1002/pssb.2221230152 ↗
35. Sehr, R. & Testardi, L. R. Optical properties of p-type Bi2Te3-Sb2Te3 alloys between 2-15 microns. J. Phys. Chem. Solids 23, 1219–1224 (1962).10.1016/0022-3697(62)90169-5 ↗
36. Smith, M. J., Knight, R. J. & Spencer, C. W. Properties of Bi2Te3-Sb2Te3 alloys. J. Appl. Phys. 33, 2186–2190 (1962).10.1063/1.1728925 ↗
37. Chen, C., Liu, D. W., Zhang, B. P. & Li, J. F. Enhanced thermoelectric properties obtained by compositional pptimization in p-type BixSb2- xTe3 fabricated by mechanical alloying and spark plasma sintering. J. Electron. Mater 40, 942–947 (2011).10.1007/s11664-010-1463-2 ↗
38. Xie, W. J., He, J., Zhu, S., Holgate, T., Wang, S. Y., Tang, X. F., Zhang, Q. J. & Tritt, T. M. J. Investigation of the sintering pressure and thermal conductivity anisotropy of melt-spun spark-plasma-sintered (Bi,Sb)2Te3 thermoelectric materials. Mater. Res. 26, 1791–1799 (2011).10.1557/jmr.2011.170 ↗
39. Lotgering, F. K. Topotactical reactions with ferromagnetic oxides having hexagonal crystal structures. J. Inorg. Nucl. Chem. 9, 113–123 (1959).10.1016/0022-1902(59)80070-1 ↗
40. Fan, X. A., Yang, J. Y., Chen, R. G., Zhu, W. & Bao, S. Q. Phase transformation and thermoelectric properties of p-type (Bi2Te3)(0.25)(Sb2Te3)(0.75) prepared by mechanical alloying and hot pressing. Mater. Sci. Eng. 438, 190–193 (2006).10.1016/j.msea.2005.12.055 ↗
41. Jiang, J., Chen, L. D., Bai, S. Q. & Yao, Q. Thermoelectric performance of p-type Bi–Sb–Te materials prepared by spark plasma sintering. J. Alloy Compd 390, 208–211 (2005).10.1016/j.jallcom.2004.07.056 ↗
42. Kim, S. S. & Aizawa, T. Thermoelectric properties for p-type (Bi2Te3)(0.2)(Sb2Te3)(0.8) alloys fabricated by shear extrusion. Met. Mater. Int. 12, 317–322 (2006).10.1007/BF03027548 ↗
43. Birkholz, U. Untersuchung der intermetallischen verbindung Bi2Te3 sowie der festen losungen Bi2-xSbxTe3 und Bi2Te3-xSex hinsichtlich ihrer eignung als material fur halbleiter-thermoelemente. Z. Phys. Chem. 13, 780–792 (1958).
44. Schultz, J. M., Tiller, W. A. & McHugh, J. P. Effects of heavy deformation and annealing on the electrical properties of Bi2Te3 . J. Appl. Phys. 33, 2443–2450 (1962).10.1063/1.1728990 ↗
45. Yim, W. M., Fitzke, E. V. & Rosi, F. D. Thermoelectric properties of Bi2Te3-Sb2Te3-Sb2Se3 pseudo-ternary alloys in the temperature range 77 to 300 K. J. Mater. Sci. 1, 52–65 (1966).10.1007/BF00549720 ↗
46. Zhao, L. D., Zhang, B. P., Li, J. F., Zhang, H. L. & Liu, W. S. Enhanced thermoelectric and mechanical properties in textured n-type Bi2Te3 prepared by spark plasma sintering. Solid State Sci. 10, 651–658 (2008).10.1016/j.solidstatesciences.2007.10.022 ↗
47. Yan, X., Poudel, B., Ma, Y., Liu, W. S., Joshi, G., Wang, H., Lan, Y. C., Wang, D. Z., Chen, G. & Ren, Z. F. Experimental studies on anisotropic thermoelectric properties and structures of n-type Bi2Te2.7Se0.3 . Nano Lett. 10, 3373–3378 (2010).10.1021/nl101156v ↗
48. Fan, X. A., Yang, J. Y., Zhu, W., Bao, S. Q., Duan, X. K., Xiao, C. J., Zhang, Q. Q. & Xie, Z. J. Effect of nominal Sb2Te3 content on thermoelectric properties of p-type (Bi2Te3)x(Sb2Te3)1−x alloys by MA–HP. Phys. D 39, 5069–5073 (2006).10.1088/0022-3727/39/23/025 ↗
49. Du, Z. L., Zhu, T. J., Chen, Y., He, J., Gao, H. L., Jiang, G. Y., Tritt, T. M. & Zhao, X. B. Roles of interstitial Mg in improving thermoelectric properties of Sb-doped Mg2Si0.4Sn0.6 solid solutions. J. Mater. Chem. 22, 6838–6844 (2012).10.1039/c2jm16694a ↗
50. Stolzer, M., Stordeur, M., Sobotta, H. & Riede, V. IR Transmission Investigations of (Bi1-xSbx)2Te3 Single Crystals. Phys. Status Solidi. B 138, 259–266 (1986).10.1002/pssb.2221380127 ↗
51. Goldsmid, H. J. & Douglas, R. W. The use of semi conductors in thermoelectric refrigeration. J. Appl. Phys. 5, 386–390 (1954).
52. Ivanova, L. D. & Granatkina, Y. U. Properties of single-crystals in the Sb2Te3-Bi2Te3 solid-solution system. Inorg. Mater. 31, 678–681 (1995).
53. Li, J. H., Tan, Q., Li, J. F., Liu, D. W., Li, F., Li, Z. Y., Zou, M. M. & Wang, K. BiSbTe-based nanocomposites with high ZT: the effect of SiC nanodispersion on thermoelectric properties. Adv. Funct. Mater. 23, 4317–4323 (2013).10.1002/adfm.201300146 ↗