journal article·2021-11

Influence of a Ni Plating Surface Preparation on Transient Liquid Phase Bonding Behaviour of Inconel 718/BNi-2

Joel M. Chapman, Stephen F. Corbin, Eric D. Moreau

Publisher page

Abstract

The influence of a Ni plating surface treatment on transient liquid phase bonding (TLPB) of superalloys was investigated through a comparison of BNi-2 filler metal joints made with IN718 base metals (BM) with and without a Ni plating surface treatment. Interdiffusion between the BM and Ni plating occurred during initial heating, creating a compositional gradient at the faying surface. This resulted in the formation of a boride free denuded zone immediately below the BM faying surface. In parallel, the Ni plating acted as a diffusion barrier against the filler metal, preventing BM dissolution (BMD). The lack of BMD was accompanied by a reduced initial boron uptake by the BM and little gap widening in Ni-plated samples. The rate of IS was approximately the same regardless of surface preparation. Overall, the presence of a Ni plating reduced the time to complete isothermal solidification by approximately 25 pct, primarily due to the prevention of BMD and the associated gap widening.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Intermetallics and Advanced Alloy Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. W.D. Macdonald and T.W. Eagar: Annu. Rev. Mater. Sci., 1992, vol. 22, pp. 23–46.10.1146/annurev.ms.22.080192.000323 ↗
2. G.O. Cook and C.D. Sorensen: J. Mater. Sci., 2011, vol. 46, pp. 5305–23.10.1007/s10853-011-5561-1 ↗
3. M.M. Schwartz: Brazing Manual. ASM International, Materials Park, 2001, pp. 297–301.
4. K. Lankiewicz, M. Baranowski, T. Babul, and S. Kowalski: Arch. Metall. Mater., 2015, vol. 60(2A), pp. 739–45.10.1515/amm-2015-0200 ↗
5. H.D. Solomon, R.E. Delair, and J. Thyssen: Weld. J., 2003, vol. 82(10), pp. 278S-287S.
6. M.A. Arafin, M. Medraj, D.P. Turner, and P. Bocher: Mater. Sci. Eng. A., 2007, vol. 447(1–2), pp. 125–33.10.1016/j.msea.2006.10.045 ↗
7. M. Pouranvari, A. Ekrami, A.H. Kokabi, and H.N. Han: Met. Mater. Int., 2013, vol. 19(5), pp. 1091–99.10.1007/s12540-013-5026-y ↗
8. M. Pouranvari, A. Ekrami, and A.H. Kokabi: Can. Metall. Q., 2014, vol. 53(1), pp. 38–46.10.1179/1879139513Y.0000000076 ↗
9. M. Pouranvari, A. Ekrami, and A.H. Kokabi: Mater. Sci. Technol., 2014, vol. 30(1), pp. 109–15.10.1179/1743284713Y.0000000320 ↗
10. M. Pouranvari and M.S. Mousavizadeh: Mater Technol., 2015, vol. 49(2), pp. 247–51.
11. J. Chapman, 2019, MASc Thesis, Dalhousie University
12. D.C. Murray and S.F. Corbin: J. Mater. Process. Technol., 2017, vol. 248, pp. 92–102.10.1016/j.jmatprotec.2017.05.013 ↗
13. D.M. Turriff, S.F. Corbin, and M. Kozdras: Acta Mater., 2010, vol. 58(4), pp. 1332–41.10.1016/j.actamat.2009.10.037 ↗
14. M.L. Kuntz, Y. Zhou, and S.F. Corbin: Metall Mater. Trans. A., 2006, vol. 37(8), pp. 2493–2504.10.1007/BF02586222 ↗
15. M.L. Kuntz, B. Panton, S. Wasiur-Rahman, Y. Zhou, and S.F. Corbin: Metall Mater. Trans. A., 2013, vol. 44(8), pp. 3708–20.10.1007/s11661-013-1704-0 ↗
16. E.D. Moreau and S.F. Corbin: Met and Mater Trans. A., 2020, vol. 51(6), pp. 2882–92.10.1007/s11661-020-05724-1 ↗
17. Y. Zhou, W.F. Gale, and T.H. North: Int. Mater. Rev., 1995, vol. 40(5), pp. 181–96.10.1179/imr.1995.40.5.181 ↗
18. M. Pouranvari, A. Ekrami, and A.H. Kokabi: Sci. Technol. Weld. Join., 2018, vol. 23(1), pp. 13–18.10.1080/13621718.2017.1327934 ↗
19. B. Zhang, G. Sheng, Y. Jiao, Z. Gao, X. Gong, H. Fan, and J. Zhong: J. Alloys Compd., 2017, vol. 695, pp. 3202–10.10.1016/j.jallcom.2016.11.306 ↗
20. E. Lugscheider and K.-D. Partz: Weld. J. WRS., 1983, vol. 24, pp. 160–64.
21. E.D. Moreau and S.F. Corbin: Met and Mater Trans. A., 2020, vol. 51(12), pp. 6307–17.10.1007/s11661-020-06057-9 ↗
22. E.D. Moreau and S.F. Corbin: Met and Mater Trans. A., 2020, vol. 51(8), pp. 3906–19.10.1007/s11661-020-05844-8 ↗