Phase Stress Partition in Gray Cast Iron Using In Situ Neutron Diffraction Measurements
Source abstract
Abstract
Gray cast iron comprises α-Fe, Fe3C and graphite with their different anisotropies in terms of structure and mechanical behavior. We perform two different deformation paths as tension-compression and compression-tension on bulk gray iron to capture the stress partitioning. Using in situ neutron diffraction, the composite-like deformation behaviors of α-Fe and Fe3C are revealed simultaneously. Within the elastic deformation stage, both deformation paths do not cause load transfer. However, when the applied compressive stress exceeds 300 MPa, there is a clear load sharing in both paths. From microscopic examinations, the debonding between matrix and graphite is clarified.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. 1. E. Martínez, F. Sanz, S. Pellegrini, E. Jiménez, and J. Blanco: Renewable Energy, 2009, vol. 34, pp. 667-73.10.1016/j.renene.2008.05.020 ↗
2. 2. A. Sadeghi, A. Moloodi, M. Golestanipour, and M.M. Shahri: J. Mater. Res. Technol., 2017, vol. 6, pp. 90-95.10.1016/j.jmrt.2016.09.003 ↗
3. 3. M.A. Azeem, M.K. Bjerre, R.C. Atwood, N. Tiedje, and P.D. Lee: Acta Mater., 2018, vol. 155, pp. 393-401.10.1016/j.actamat.2018.06.007 ↗
4. 4. O. Oloyede, T.D. Bigg, R.F. Cochrane, and A.M. Mullis: Mate. Sci. Eng. A, 2016, vol. 654, pp. 143-50.10.1016/j.msea.2015.12.020 ↗
5. 5. O. Oloyede, R.F. Cochrane and A.M. Mullis: J. Alloys Compd., 2017, vol. 707, pp. 347-50.10.1016/j.jallcom.2016.08.214 ↗
6. M. Moonesan, A. Honarbakhshraouf, F. Madah, and A. Habibollah Zadeh: J. Alloys Compd., 2012, vol. 520, pp. 226-31.10.1016/j.jallcom.2012.01.027 ↗
7. A.V. Adedayo: J. Braz. Soc. Mech. Sci. Eng., 2010, vol. 32, pp. 171-75.
8. S. Spooner, E.A. Payzant, and C.R. Hubbard: 2nd International Conference on Quenching & Control of Distortion, Cleveland, OH, 4–7 November 1996.
9. 9. F. Smith, J. Markgraaff, D. Marais, and A.M. Venter: Mater. Res. Proc., 2018, vol. 4, pp. 79-84.10.21741/9781945291678-12 ↗
10. 10. P. Schmidt, L.P. Ru, V. Davydov, M. Lundberg, M. Ahmad, T. Vuoristo, D. Bäckström, and S. Johansson: Adv. Mater. Res., 2014, vol. 996, pp. 586-91.10.4028/www.scientific.net/AMR.996.586 ↗
11. 11. T.L. Lee, J. Mi, S. Ren, S. Zhao, J. Fan, S. Kabra, S. Zhang, and P.S. Grant: Acta Mater., 2018, vol. 155, pp. 318-30.10.1016/j.actamat.2018.05.055 ↗
12. T.L. Starr, K. Rafi, B. Stucker, and C.M. Scherzer: Proceedings of the Solid Freeform Fabrication Symposium, University of Texas, Austin, 2012, pp. 439–46.
13. 13. D. Raabe, S. Sandlöbes, J. Millán, D. Ponge, H. Assadi, M. Herbig and P.P. Choi: Acta Mater., 2013, vol. 61, pp. 6132-52.10.1016/j.actamat.2013.06.055 ↗
14. 14. F. Qian and W. M. Rainforth: J Mater Sci, 2019, vol. 54, pp. 6624-31.10.1007/s10853-019-03319-9 ↗
15. 15. L.E. Murr, E. Martinez, J. Hernandez, S. Collins, K.N. Amato, S.M. Gaytan, and P.W. Shindo: J. Mater. Res. Technol., 2012, vol. 1, pp. 167-77.10.1016/S2238-7854(12)70029-7 ↗
16. 16. L. Facchini, N. Vicente Jr., I. Lonardelli, E. Magalini, P. Robotti, and A. Molinari: Adv. Eng. Mater., 2010, vol. 12, pp. 184-88.10.1002/adem.200900259 ↗
17. 17. T. LeBrun, T. Nakamoto, K. Horikawa, and H. Kobayashi: Materials & Design, 2015, vol. 81, pp. 44-53.10.1016/j.matdes.2015.05.026 ↗
18. 18. S. Gorsse, C. Hutchinson, M. Goune, and R. Banerjee: Sci Technol Adv Mater: 2017, vol. 18, pp. 584-610.10.1080/14686996.2017.1361305 ↗
19. 19. M. Islam, T. Purtonen, H. Piili, A. Salminen, and O. Nyrhilä: Physics Procedia, 2013, vol. 41, pp. 835-42.10.1016/j.phpro.2013.03.156 ↗
20. 20. E.W. Huang, S.Y. Lee, J. Jain, Y. Tong, K. An, N.-T. Tsou, T.-N. Lam, D. Yu, H. Chae, S.-W. Chen, S.-M. Chen, and H.-S. Chou: Intermetallics, 2019, vol. 109, pp. 60-67.10.1016/j.intermet.2019.03.004 ↗
21. 21. G. Ghosh: AIP Advances, 2015, vol. 5, p. 087102.10.1063/1.4928208 ↗
22. 22. Y. Tomota, H. Tokuda, Y. Adachi, M. Wakita, N. Minakawa, A. Moriai, and Y. Morii: Acta Mater., 2004, vol. 52, pp. 5737-45.10.1016/j.actamat.2004.08.016 ↗
23. 23. S. Harjo, N. Tsuchida, J. Abe. and W. Gong: Scientific Reports, 2017, vol. 7, p. 15149.10.1038/s41598-017-15252-5 ↗
24. 24. S. Morooka, O. Umezawa, S. Harjo, K. Hasegawa, and Y. Toji, Tetsu-to-Hagane, 2012, vol. 98, pp. 311-19.10.2355/tetsutohagane.98.311 ↗
25. 25. M. Kriška, J. Tacq, K.V. Acker, M. Seefeldt, and S.V. Petegem: J. Phys.: Conf. Ser., 2012, vol. 340, p. 012101.
26. 26. Y. Wang, Y. Tomota, S. Harjo, W. Gong and T. Ohmura: Mate. Sci. Eng. A, 2016, vol. 676, pp. 522-30.10.1016/j.msea.2016.08.122 ↗
27. ASTM International. ASTM E606/E606M-12, ASTM International, West Conshohocken, PA, 2012.
28. 28. S.C. Vogel, C. Hartig, L. Lutterotti, R.B. Von Dreele, H.-R. Wenk, and D.J. Williams: Powder Diffraction, 2004, vol. 19, pp. 65-68.10.1154/1.1649961 ↗
29. Wenk, H-R., L. Lutterotti, and S. Vogel. "Texture analysis with the new HIPPO TOF diffractometer." Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment 515.3 (2003): 575-588.10.1016/j.nima.2003.05.001 ↗
30. S. Matthies, J. Pehl, H.-R. Wenk, L. Lutterotti, and S.C. Vogel: Journal of Applied Crystallography, 2005, vol. 38, pp. 462-75.10.1107/S0021889805006187 ↗
31. Takajo, Shigehiro, and Sven C. Vogel. "Determination of pole figure coverage for texture measurements with neutron time-of-flight diffractometers." Journal of Applied Crystallography 51.3, 895-900.10.1107/S1600576718007732 ↗
32. 30. R.I. Barabash, E.W. Huang, J.J. Wall, J.H. Wilkerson, Y. Ren, W. Liu, S.C. Vogel, G.E. Ice, L.M. Pike, and P.K. Liaw: Mate. Sci. Eng. A, 2010, vol. 528, pp. 3-10.10.1016/j.msea.2010.07.035 ↗
33. L. Lutterotti, S. Matthies, H.-R. Wenk, A.S. Schultz, J. Appl. Phys., 1997, 81:594-600.10.1063/1.364220 ↗
34. 32. K. An, H. Skorpenske, A. Stoica, D. Ma, X.-L. Wang, and E. Cakmak: Metall. Mater. Trans. A, 2011, vol. 42, pp. 95-99.10.1007/s11661-010-0495-9 ↗
35. 33. E.W. Huang and P.K. Liaw: MRS Bulletin, 2019, vol. 44, pp. 847-53.10.1557/mrs.2019.257 ↗
36. 34. E.W. Huang, D. Yu, J.-W. Yeh, C. Lee, K. An and S.-Y. Tu: Scripta Mater., 2015, vol. 101, pp. 32-35.10.1016/j.scriptamat.2015.01.011 ↗
37. 35. E.-W. Huang, R.I. Barabash, G.E. Ice, W. Liu, Y.-L. Liu, J.-J. Kai and P.K. Liaw, JOM, 2009, vol. 61(12), p. 53-58.10.1007/s11837-009-0181-9 ↗
38. 36. E.W. Huang, R.I. Barabash, B. Clausen, Y.L. Liu, J.J. Kai, G.E. Ice, K.P. Woods and P.K. Liaw: International Journal of Plasticity, 2010, vol. 26, pp. 1124-37.10.1016/j.ijplas.2010.01.003 ↗
39. 38. H.R. Wenk, L. Lutterotti, and S.C. Vogel: Powder Diffraction, 2010, vol. 25, pp. 283-96.10.1154/1.3479004 ↗
40. 39. E. R. Weibel, G. S. Kistler, and W.F. Scherle: The Journal of Cell Biology, 1966, vol. 30, pp. 23-38.10.1083/jcb.30.1.23 ↗
41. G.V. Voort, Tech-Notes, Research and Technology Buehler Ltd., Lake Bluff, Illinois, U.S.A, 2015, vol. 1 (5), p. 1.
42. Allen.C. Larson and Robert.B. Von Dreele: Los Alamos Natl. Lab. Rep. LAUR, 2004, vol. 86, pp. 86–748.
43. D. Naito, S. Kubota, S. Harjo, and Y. Tomota: ISIJ International, 2013, vol. 53, pp. 1292-94.10.2355/isijinternational.53.1292 ↗
44. M.L. Young, J.D. Almer, M.R. Daymond, D.R. Haeffner, and D.C. Dunand: Acta Mater., 2007, vol. 55, pp. 1999-2011.10.1016/j.actamat.2006.11.004 ↗
45. H. Shen and C.J. Lissenden: Mate. Sci. Eng. A, 2002, vol. 338, pp. 271-81.10.1016/S0921-5093(02)00094-1 ↗
46. M.T. Hutchings, P.J. Withers, T.M. Holden, T. Lorentzen: Introduction to the Characterization of Residual Stress by Neutron Diffraction, 1st ed., CRC Press, Boca Raton, 2005.10.1201/9780203402818 ↗
47. C. Jiang, S.G. Srinivasan, A. Caro, and S.A. Maloy: Journal of Applied Physics, 2008, vol. 103, p. 043502.10.1063/1.2884529 ↗
48. P.J. Withers and A.P. Clarke: Acta Mater., 1998, vol. 46, pp. 6585-98.10.1016/S1359-6454(98)00297-3 ↗
49. E.W. Huang, R. Barabash, B. Clausen and P.K. Liaw: Metall. Mater. Trans. A, 2012, vol. 43, pp. 1454-61.10.1007/s11661-011-0972-9 ↗
50. E.W. Huang, C.K. Chang, P.K. Liaw, and T.R. Suei: Fatigue & Fracture of Engineering Materials & Structures, 2016, vol. 39, pp. 675-85.10.1111/ffe.12414 ↗
51. E.W. Huang, G. Csiszár, Y.C. Lo, Y.L. Huang, W.J. Lee, T. Ungár, and P.K. Liaw: Adv. Eng. Mater., 2012, vol. 14, pp. 902-08.10.1002/adem.201200057 ↗
52. V. Norman and M. Calmunger: International Journal of Plasticity, 2019, vol. 115, pp. 200-15.10.1016/j.ijplas.2018.11.019 ↗
53. S.A. Brauer, W.R. Whittington, K.L. Johnson, B. Li, H. Rhee, P.G. Allison, C.K. Crane, and M.F. Horstemeyer: Journal of Engineering Materials and Technology, 2017, vol. 139, p. 021013.10.1115/1.4035616 ↗