journal article·2020-01

Deep Understanding of the Influence of the Process Parameters During Linear Friction Welding on the Joint Quality and the Microstructural Changes of Two Mono-Material Titanium Alloy Joints: The β-Metastable Ti-5Al-2Sn-2Zr-4Mo-4Cr (Ti17) and the Near-α Ti-6Al-2Sn-4Zr-2Mo (Ti6242)

Dorick Ballat-Durand, Salima Bouvier, Marion Risbet

Publisher page

Abstract

Linear friction welding (LFW) of near-α Ti-6Al-2Sn-4Zr-2Mo (Ti6242) and β-metastable Ti-5Al-2Sn-2Zr-4Mo-4Cr (Ti17) was studied through eight sets of process parameters. Varying the main LFW process parameters revealed that: (1) increasing the ratio between the normal pressure and local flow stress shortens the duration of friction phase (III); this ratio is influenced by the normal pressure and/or heat generated by the longitudinal deformation conditions, the latter being driven by the oscillation parameters (amplitude and frequency); (2) the joint and PAZ extents can be drastically lowered by favoring the extrusion of the heated material through higher normal pressures; (3) the presence of defects is mostly due to contaminant layers initially present on the contact surfaces; these defects can be dissipated into the bulk with the help of an enhanced recrystallization and/or material blending; (4) the two-component {110}〈111〉 β texture intensity is mostly influenced by the amplitude and degree of recrystallization. Subjecting three significantly different Ti17 joints to β-annealing resulted in similar homogenized microstructures and defect dissolution. The different material responses of Ti17 and Ti6242 to LFW showed the necessity of defining optimized sets of process parameters depending on the welded materials and initial microstructures.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Advanced Welding Techniques Analysis · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Liu, Z. & Welsch, G. : Metall. Trans. A, 1988, vol. 19, pp. 527–42.10.1007/BF02649267 ↗
2. Huang, J. L., Warnken, N., Gebelin, J.-C., Strangwood, M. & Reed, R. C. : Acta Mater., 2012, vol. 60, pp. 3215–25.10.1016/j.actamat.2012.02.035 ↗
3. Maalekian, M. : Sci. Technol. Weld. Join., 2007, vol. 12, pp. 738–59.10.1179/174329307X249333 ↗
4. Vairis, A. & Frost, M. : Wear, 1998, vol. 217, pp. 117–31.10.1016/S0043-1648(98)00145-8 ↗
5. Ballat-Durand, D., Bouvier, S., Risbet, M. & Pantleon, W. : Mater. Charact., 2018, vol. 144, 661–70.10.1016/j.matchar.2018.08.013 ↗
6. Ballat-Durand, D., Bouvier, S., Risbet, M. & Pantleon, W. : Mater. Charact., 2019, vol. 151, pp. 38-52.10.1016/j.matchar.2019.02.027 ↗
7. Li, W., Vairis, A., Preuss, M. & Ma, T. : Int. Mater. Rev., 2016, vol. 61, pp. 71–100.10.1080/09506608.2015.1109214 ↗
8. McAndrew, A. R., Colegrove, P. A., Bühr, C., Flipo, B. C. D. & Vairis, A. : Prog. Mater. Sci., 2018, vol. 92, pp. 225–57.10.1016/j.pmatsci.2017.10.003 ↗
9. Wanjara, P. & Jahazi, M. : Metall. Mater. Trans. A, 2005, vol. 36, pp. 2149–64.10.1007/s11661-005-0335-5 ↗
10. Romero, J., Attallah, M. M., Preuss, M., Karadge, M. & Bray, S. E. : Acta Mater., 2009, vol. 57, pp. 5582–92.10.1016/j.actamat.2009.07.055 ↗
11. Lütjering, G. & Williams, J. C. : Titanium (Springer Berlin Heidelberg, 2003).10.1007/978-3-540-71398-2 ↗
12. G.W. Stachowiak and A.W. Batchelor: Engineering Tribology, Elsevier, Amsterdam, 2001.
13. Humphreys, J., Roher, G. S. & Rollett, A. : Recrystallization and Related Annealing Phenomena (Elsevier, Amsterdam, 2017).
14. Turner, R., Gebelin, J.-C., Ward, R. M. & Reed, R. C. : Acta Mater., 2011, vol. 59, pp. 3792–803.10.1016/j.actamat.2011.02.028 ↗
15. V.K. Manupati, G. Rajyalakshmi, M.L.R. Varela, J. Machado, and G.D. Putnik: Innovation, Engineering and Entrepreneurship, J. Machado, F. Soares, and G. Veiga, eds., Springer, Berlin, 2018, vol. 505, pp. 608–15.10.1007/978-3-319-91334-6_83 ↗
16. Smidoda, K., Gottschalk, W. & Gleiter, H. : Acta Metall., 1978, vol. 26, pp. 1833–36.10.1016/0001-6160(78)90095-0 ↗
17. Y. Mizuno: Temperature Dependence of Oxide Decomposition on Titanium Surfaces in UHV. United States. https://doi.org/10.2172/798917.10.2172/798917 ↗
18. Li, W., Suo, J., Ma, T., Feng, Y. & Kim, K. : Mater. Sci. Eng. A, 2014, vol. 599, pp. 38–45.10.1016/j.msea.2014.01.071 ↗
19. Garcia, J. M. & Morgeneyer, T. F. : Fatigue & Fracture of Engineering Materials & Structures, 2019, vol. 42, pp. 1100-17.10.1111/ffe.12973 ↗
20. Vishwakarma, K., Ojo, O., Wanjara, P. & Chaturvedi, M. : JOM, 2014, vol. 66, pp. 2525-34.10.1007/s11837-014-0938-7 ↗
21. Masoumi, F., Shahriari, D., Jahazi, M., Cormier, J. & Flipo, B. C. D. : Metall. Mater. Trans. A, 2017, vol. 48, pp. 2886–99.10.1007/s11661-017-4067-0 ↗
22. Dalgaard, E., Wanjara, P., Gholipour, J., Cao, X. & Jonas, J. J. : Acta Mater., 2012, vol. 60, pp. 770–80.10.1016/j.actamat.2011.04.037 ↗