journal article·2019-01

State of Grain Boundary Misorientation Due to Multiaxiality in Austenitic Stainless Steel

Rima Dey, Anindya Das, Soumitro Tarafder, S. Sivaprasad

Publisher page

Abstract

Electron backscatter diffraction was used to study grain character under multiaxiality. Nonproportional loading conditions employing a triangular and sinusoidal wavepath resulted in higher low-angle grain boundaries in austenitic stainless steel. Contrastingly, significant martensitic transformation resulted from nonproportional cycling for the trapezoidal path, leading to increased medium-angle grain boundaries. For proportional loading, high-angle grain boundaries were dominant, owing to participation of limited grains in the deformation process. All results were substantiated through electron microscopy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Material Properties and Failure Mechanisms · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. D.L. McDowell: Proc. Int. Conf. on Constitutive Laws for Engineering Materials, Tucson, AZ, 1983, C.S. Desai and R.H. Gallagher, eds., 1983, p. 125.
2. K. Kanazawa, K.J. Miller, and M.W. Brown: Fatigue Eng. Mater. Struct., 1979, vol. 2, pp. 217–28.10.1111/j.1460-2695.1979.tb01357.x ↗
3. E. Krempl and H. Lu: ASME J. Eng. Mater. Technol., 1984, vol. 106, pp. 376–82.10.1115/1.3225733 ↗
4. S.H. Doong, D.F. Socie, and I.M. Robertson: ASME J. Eng. Mater. Technol., 1990, vol 112, pp. 456–64.10.1115/1.2903357 ↗
5. G.Z Kang and Q. Gao: Key Eng. Mater., 2004, vol. 247, pp. 247–52.10.4028/www.scientific.net/KEM.274-276.247 ↗
6. E. Tanaka, S. Murakami, and M. Ooka: J. Mech. Phys. Solids, 1985, vol. 33, pp. 559–7510.1016/0022-5096(85)90003-1 ↗
7. N. Shamsaei, A. Fatemi, and D.F. Socie: Int. J. Plasticity, 2010, vol. 26, pp. 1680–1701.10.1016/j.ijplas.2010.02.006 ↗
8. T. Itoh, M. Sakane, M. Ohnami, and K. Ameyama: J. Soc. Mater. Sci., Jpn., 1992, vol. 41, pp. 1361–6710.2472/jsms.41.1361 ↗
9. D.L. McDowell, D.R. Stahl, S.R. Stock, and S.D. Antolovich: Metall. Trans. A, 1988, vol. 19A, pp. 1277–93.10.1007/BF02662589 ↗
10. N. Shamsaei, A. Fatemi, and D.F. Socie: Int. J. Fatigue, 2011, vol. 33, pp. 597–609.10.1016/j.ijfatigue.2010.11.002 ↗
11. M. Takahiro, T. Itoh, and Z. Bao: lnt. J. Pres. Ves. Pip., 2016, vol. 139, pp. 228–36.
12. P. Arora, S.K. Gupta, V. Bhasin, R.K. Singh, S. Sivaprasad, and S. Tarafder: Int. J. Fatigue, 2016, vol. 85, pp. 98–113.10.1016/j.ijfatigue.2015.12.002 ↗
13. T. Itoh, M. Sakane, M. Ohnami, and K. Ameyama: MECAMAT ‘92, Proc. Int. Seminar on Multiaxial Plasticity, 1992, pp. 43–50.
14. S. Kida, T. Itoh, M. Sakane, M. Ohnami, and D.F. Soci: Fat. Fract. Eng. Mater. Struct., 1997, vol. 20, pp. 1375–86.10.1111/j.1460-2695.1997.tb01496.x ↗
15. G. Cailletaud, V. Doquet, and A. Pineau: in ESIS 10, Kussmaul et al., eds., 1991, pp. 131–49.
16. S. Nishino, N. Hamada, M. Sakane, M. Ohnami, N. Matsumura, and M. Tokizane: Fat. Fract. Eng. Mater. Struct., 1986, vol. 9, pp. 65–77.10.1111/j.1460-2695.1986.tb01212.x ↗
17. J.A. Bannantine and D.F. Socie: in ASTM STP 942, H.D. Solomon, G.R. Halford, L.R. Kaisand, and B.N. Leis, eds., ASTM, Philadelphia, PA, 1988, pp. 899–921.
18. J.A. Bannantine: Master’s thesis, University of Illinois at Urbana–Champaign, Champaign, IL, 1986.
19. L. Taleb and A. Hauet: Int. J. Plasticity, 2009, vol. 25, pp. 1359–85.10.1016/j.ijplas.2008.09.004 ↗
20. ASTM E 2207–08.03.01, Annual Book of ASTM Standards, ASTM, Conshohocken, PA, 2009, p. 1258.