journal article·2015-01

Effects of Alloy Composition on Microstructure and Mechanical Properties of Iron-Based Materials Fabricated by Ball Milling and Spark Plasma Sintering

Yongquan Ye, Xiaoqiang Li, Ke Hu, Shengguan Qu, Yuanyuan Li

Publisher page

Abstract

Three PM steels, Fe-0.8C, Fe-2Cu-1.5Ni-0.5Mo-0.8C, and Fe-2Cu-2Ni-1Mo-1C, were fabricated by mechanical milling and spark plasma sintering. Dense sintered samples with fine and homogeneous microstructure were obtained. According to the results of X-ray diffraction, differential scanning calorimetry, and scanning electron microscopy, it is suggested that the temperature of the sample can be ~50 K (50 °C) greater than that recorded. The microstructures of the as-sintered samples are divided into two groups. One consists of both ferritic and martensitic structures, and the others are of a ferritic structure. A considerable amount of martensite exists only in those high alloy Fe-2Cu-2Ni-1Mo-1C samples. The hardness of the sintered samples mainly depends on microstructure and composition. It shows that the hardness enhances with the volume fraction of martensite. However, a lower compressive strength is observed in the samples with higher volume fraction of martensite. The analysis of the deformation behavior demonstrates that the yield strength and ultimate strength are solely correlated to the properties of ferritic structure. Discontinuously yielding phenomenon, initial work hardening exponent, and decreasing rate of strain hardening exponent with strain are considered to be sensitive to the morphology of carbides formed in the ferritic structure.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Powder Metallurgy Techniques and Materials · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. F. Chagnon and L. Tremblay: Proceedings of Powder Metallurgy World Congress PM2004, Vienna, Austria, 17–21 October, 2004, vol. 3, pp. 205–10.
2. J.M. Torralba and M. Campos: Powder Metall. Prog., 2002, vol. 2, pp. 177–87.
3. C. Suryanarayana: Prog. Mater. Sci., 2001, vol. 46, pp. 1–184.10.1016/S0079-6425(99)00010-9 ↗
4. W.B. James: Met. Powder Rep., 1991, vol. 46, pp. 26–32.10.1016/0026-0657(91)90335-X ↗
5. Z. Livne, A. Munitz, J.C. Rawers, and R.J. Fields: Nanostruct. Mater., 1998, vol. 10, pp. 503–22.10.1016/S0965-9773(98)00094-4 ↗
6. Z.A. Munir, U. Anselmi-Tamburini, and M. Ohyanagi: J. Mater. Sci., 2006, vol. 41, pp. 763–777.10.1007/s10853-006-6555-2 ↗
7. Y.Y. Li, Y. Long, X.Q. Li, and T.W.L. Ngai: Key Eng. Mater., 2007, vol. 353–358, pp. 2143–46.10.4028/www.scientific.net/KEM.353-358.2143 ↗
8. Y.Y. Li, X.Q. Li, Y. Long, M. Shao, and W. Xia: Key Eng. Mater., 2006, vol. 315–316, pp. 445–49.10.4028/www.scientific.net/KEM.315-316.445 ↗
9. F. Hanejko, A. Taylor, A. Rawlings, and I.N. Salem: Proceedings of the World Congress on Powder Metallurgy and Particulate Materials, Orlando, USA, 16–21 June, 2002, vol. 13, pp. 35–47.
10. J.H. Hollomon and L.D. Jaffe: Trans. AIME, 1945, vol. 162, pp. 223–49.
11. C.C. Koch: Nanostruct. Mater., 1997, vol. 9, pp. 13–22.10.1016/S0965-9773(97)00014-7 ↗
12. X.J. Hao, Z.G. Liu, K. Masuyama, T. Rikimaru, M. Umemoto, K. Tsuchiya, and S.M. Hao: Mater. Sci. Technol. Lond., 2001, vol. 17, pp. 1347–52.10.1179/026708301101509548 ↗
13. H. Danninger, C. Gierl, S. Kremel, G. Leitner, K. Jaenicke-Roessler, and Y. Yu: Powder Metall. Prog., 2002, vol. 2, pp. 125–40.
14. Y. Xu, Z.G. Liu, M. Umemoto, and K. Tsuchiya: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2195–2203.10.1007/s11661-002-0051-3 ↗
15. S. Ohsaki, K. Hono, H. Hidaka, and S. Takaki: Scripta Mater., 2005, vol. 52, pp. 271–76.10.1016/j.scriptamat.2004.10.020 ↗
16. E.M. Taleff, C.K. Syn, D.R. Lesuer, and O.D. Sherby: Metall. Mater. Trans. A, 1996, vol. 27, pp. 111–18.10.1007/BF02647751 ↗
17. Y. Liu, T. He, G. Peng, and F. Lian: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 2144–52.10.1007/s11661-011-0608-0 ↗
18. A. Fernández Vicente, M. Carsí, F. Peñalba, and O.A. Ruano: Fatigue Fract. Eng. Mater. Struct., 2006, vol. 29, pp. 817–28.10.1111/j.1460-2695.2006.01007.x ↗
19. S.A. Khodir, Y. Morisada, R. Ueji, and H. Fujii: Mater. Sci. Eng. A, 2012, vol. 558, pp. 572–78.10.1016/j.msea.2012.08.052 ↗
20. M. Nygren and Z. Shen: Key Eng. Mater., 2004, vol. 264, pp. 719–24.10.4028/www.scientific.net/KEM.264-268.719 ↗
21. H. Dong, X. Sun, W. Hui, S. Zhang, J. Shi, and M. Wang: ISIJ Int., 2008, vol. 48, pp. 1126–32.10.2355/isijinternational.48.1126 ↗
22. Y. Adachi, T. Tomida, and S. Hinotani: Tetsu-to-Hagane, 1999, vol. 85, pp. 620–27.10.2355/tetsutohagane1955.85.8_620 ↗
23. F.L. Lian, H.J. Liu, J.J. Sun, X.J. Sun, S.W. Guo, Y.N. Liu, and L.X. Du: Mater. Res., 2013, vol. 28, pp. 757–65.10.1557/jmr.2012.397 ↗
24. T. Furuhara, K. Kikumoto, H. Saito, T. Sekine, T. Ogawa, S. Morito, and T. Maki: ISIJ Int., 2008, vol. 48, pp. 1038–45.10.2355/isijinternational.48.1038 ↗
25. A. Garcia-Junceda, C. Capdevila, F.G. Caballero, and C. Garcia de Andres: Scripta Mater., 2008, vol. 58, pp. 134–37.10.1016/j.scriptamat.2007.09.017 ↗
26. H.S. Yang, H.K.D.H. Bhadeshia: Scripta Mater., 2009, vol. 60, pp. 493–95.10.1016/j.scriptamat.2008.11.043 ↗
27. I. Lonardelli, M. Bortolotti, W. van Beek, L. Girardini, M. Zadra, and H.K.D.H. Bhadeshia: Mater. Sci. Eng. A, 2012, vol. 555, pp. 139–47.10.1016/j.msea.2012.06.043 ↗
28. Y.G. Gurevich, V.I. Rakhmanov, and Y.I. Pozhidaev: Powder Metall. Met. Ceram., 1979, vol. 18, pp. 407–10.10.1007/BF00802333 ↗
29. F.J. Semel and D.A. Lados: Powder Metall., 2009, vol. 52, pp. 282–90.10.1179/174329008X286712 ↗
30. R.W. Hertzberg: Deformation and Fracture Mechanics of Engineering Materials, 4th ed., Wiley, New York, 1996, p. 134.
31. H.K.D.H. Bhadeshia and R.W.R.W. Honeycombe: Steels: Microstructure And Properties, 3rd ed., Butterworth-Heinemann, Oxford, 2006, pp. 26–34.
32. R. Abbaschian, L. Abbaschian, and R. Reed-Hill: Physical Metallurgy Principles, 4th ed., Cengage Learning, Stamford, 2006, pp. 275–76.
33. E.O. Hall: Yield Point Phenomenon in Metals and Alloys, Macmillan, London, 1970, pp. 64–126.10.1007/978-1-4684-1860-6 ↗
34. J.C. Rawers: J. Mater. Sci., 1999, vol. 34, pp. 941–44.10.1023/A:1004571323025 ↗
35. K. Oh-Ishi, H.W. Zhang, T. Ohkubo, and K. Hono: Mater. Sci. Eng. A, 2007, vol. 456, pp. 20–27.10.1016/j.msea.2006.12.002 ↗
36. Z.Q. Lv, B. Wang, Z.H. Wang, S.H. Sun, and W.T. Fu: Mater. Sci. Eng. A, 2013, vol. 574, pp. 143–48.10.1016/j.msea.2013.02.059 ↗
37. Y. Xiong, T. He, Z. Guo, H. He, F. Ren, and A.A. Volinsky: Mater. Sci. Eng. A, 2013, vol. 563, pp. 163–67.10.1016/j.msea.2012.11.068 ↗
38. S.L. Semiatin: ASM Handbook vol. 14A, Metalworking: Bulk Forming, ASM International, Materials Park, OH, 2005, p. 210.10.31399/asm.hb.v14a.9781627081856 ↗
39. R.E. Reed-Hill, W.R. Cribb, and S.N. Monteiro: Metall. Trans., 1973, vol. 4, pp. 2665–67.10.1007/BF02644276 ↗
40. P.B. Jaoul: J. Mech. Phys. Solids, 1957, vol. 5, pp. 95–102.10.1016/0022-5096(57)90054-6 ↗
41. C. Crussard: Rev. Metall, 1953, vol. 50, pp. 697–710.10.1051/metal/195350100697 ↗
42. A. Bag, K.K. Ray, and E.S. Dwarakadasa: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1193–1202.10.1007/s11661-999-0269-4 ↗
43. Z.H. Cai, H. Ding, X. Xue, J. Jiang, Q.B. Xin, and R. Misr: Scripta Mater., 2013, vol. 68, pp. 865–68.10.1016/j.scriptamat.2013.02.010 ↗
44. M. Umemoto, K. Tsuchiya, Z.G. Liu, and S. Sugimoto: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1785–94.10.1007/s11661-006-0249-x ↗
45. A. Kumar, S.B. Singh, and K.K. Ray: Mater. Sci. Eng. A, 2008, vol. 474, pp. 270–82.10.1016/j.msea.2007.05.007 ↗
46. Z. Jiang, Z. Guan, and J. Lian: J. Mater. Sci., 1993, vol. 28, pp. 1814–18.10.1007/BF00595750 ↗
47. A.M. Garde, E. Aigeltinger, and R.E. Reed-Hill: Metall. Trans., 1973, vol. 4, pp. 2461–68.10.1007/BF02669391 ↗
48. B. Karlsson and G. Linden: Mater. Sci. Eng., 1975, vol. 17, pp. 153–64.10.1016/0025-5416(75)90039-7 ↗