journal article·2016-05

Replication Experiments in Microgravity Liquid Phase Sintering

Randall M. German, John L. Johnson

Publisher page

Abstract

Although considerable experience exists with sintering on Earth, the behavior under reduced gravity conditions is poorly understood. This study analyzes replica microgravity liquid phase sintering data for seven tungsten alloys (35 to 88 wt pct tungsten) sintered for three hold times (1, 180, or 600 minutes) at 1773 K (1500 °C) using 0.002 pct of standard gravity. Equivalent sintering is performed on Earth using the same heating cycles. Microgravity sintering results in a lower density and more shape distortion. For Earth-based sintering, minimized distortion is associated with low liquid contents to avoid solid settling and slumping. Distortion in microgravity sintering involves viscous spreading of the component at points of contact with the containment crucible. Distortion in microgravity is minimized by short hold times; long hold times allow progressive component reshaping toward a spherical shape. Microgravity sintering also exhibits pore coalescence into large, stable voids that cause component swelling. The microgravity sintering results show good replication in terms of mass change and sintered density. Distortion is scattered but statistically similar between the replica microgravity runs. However, subtle factors, not typically of concern on Earth, emerge to influence microgravity sintering, such that ground experiments do not provide a basis to predict microgravity behavior.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · High-pressure geophysics and materials · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. O. Gilia, C. Hosserond, and D. Bouvard: Acta Mater., 2001, vol. 49, pp. 1413-20.10.1016/S1359-6454(01)00042-8 ↗
2. A. Petersson and J. Agren: in Proceedings Sintering 2003, R.G. Cornwall, R.M. German, and G.L. Messing, eds., Materials Research Institute, Pennsylvania State Univ., University Park, PA, 2003.
3. R. M. German, P. Suri, N. Erhardt and S. H. Chung: Adv. Powder Metall. Part. Mater., 2004, Part 5, pp. 41-50.
4. R. Bollina and R.M. German: Proc. PM 2004 Powder Metall. World Congress (Vienna, Austria), vol. 2, European Powder Metallurgy Assoc., Shrewsbury, UK, 2004, pp. 196–202.
5. C. M. Kipphut, A. Bose, S. Farooq and R. M. German: Metall. Trans., 1988, vol. 19A, pp. 1905-13.10.1007/BF02645192 ↗
6. R. Raman and R. M. German: Metall. Mater. Trans., 1995, vol. 26A, pp. 653-9.10.1007/BF02663915 ↗
7. R.M. German, S.J. Park, S.H. Chung, and J.L. Johnson: Proc. 2006 Int. Conf. Tungsten, Refract. Hardmetals IV, A. Bose and R. Dowding, eds., Metal Powder Industries Federation, Princeton, NJ, 2006, pp. 71–82.
8. R. Ganesan, A. Griffo and R. M. German: Metall. Mater. Trans., 1998, vol. 29A, pp. 659-64.10.1007/s11661-998-0146-6 ↗
9. J. A. Alvarado-Contreras, E. A. Olevsky and R. M. German: Mech. Res. Commun., 2013, vol. 50, pp. 8-11.10.1016/j.mechrescom.2013.02.007 ↗
10. J. A. Alvarado-Contreras, R. M. German, A. L. Maximenko and E. A. Olevsky: Metall. Mater. Trans., 2014, vol. 45A, pp. 927-33.10.1007/s11661-013-2050-y ↗
11. H. L. Frandsen, E. Olevsky, T. T. Molla, V. Esposito, R. Bjork and N. Pryds: J. Am. Ceram. Soc., 2013, vol. 96, pp. 80-9.10.1111/jace.12070 ↗
12. A. N. Niemi and T. H. Courtney: Acta Metall., 1983, vol. 31, pp. 1393-1401.10.1016/0001-6160(83)90009-3 ↗
13. T. H. Courtney: Metall. Trans., 1984, vol. 15A, pp. 1065-74.10.1007/BF02644699 ↗
14. R. M. German: Adv. Powder Metall., 1991, vol. 4, pp. 183-94.
15. D. F. Heaney, R. M. German and I. S. Ahn: J. Mater. Sci., 1995, vol. 30, pp. 5805-12.10.1007/BF00356725 ↗
16. A. Eliasson, L. Ekbom and H. Fredriksson: Powder Metall., 2008, vol. 51, pp. 343-49.10.1179/174329008X293732 ↗
17. Y. Liu, D. F. Heaney and R. M. German: Acta Metall. Mater., 1995, vol. 43, pp. 1587-92.10.1016/0956-7151(94)00363-M ↗
18. R.M. German: Proc. 4th Int. Conf. Sci., Technol. Appl. Sinter., D. Bouvard, ed., Institut National Polytechnique de Grenoble, Grenoble, France, 2005, pp. 303–06.
19. Y. Liu, R. G. Iacocca, J. L. Johnson, R. M. German and S. Kohara: Metall. Mater. Trans., 1995, vol. 26A, pp. 2484-86.10.1007/BF02671264 ↗
20. Z. S. Nikolic: Sci. Sinter., 1999, vol. 31, pp. 83-89.
21. A.J.G. Van Diemen and H.N. Stein: Sixth Eur. Symp. Mater. Sci. Under Microgravity Cond., ESA SP-256, European Space Agency, Paris, France. 1987. pp. 173–77.
22. V. Rosenkranz and G.H. Frischat: Mater. Sci. Under Microgravity, Results of Spacelab-1, ESA SP-222, European Space Agency, Paris, France. 1984. pp. 353–57.
23. A. Kneissl and H. Fischmeister: Sci., 1984, vol. 225, pp. 198-200.10.1126/science.225.4658.198 ↗
24. J. R. Cahoon, M. C. Chaturvedi and K. N. Tandon: Metall. Mater. Trans., 1998, vol. 29A, pp. 1101-11.10.1007/s11661-998-1019-8 ↗
25. Z. Cheng, P. M. Chaikin, J. Zhu, W. B. Russel and W. V. Meyer: Phys. Rev. Lett., 2002, vol. 88, pp. 15501(1-4).
26. R. M. German: Metall. Mater. Trans., 1995, vol. 26A, pp. 279-88.10.1007/BF02664666 ↗
27. J. L. Johnson, A. Upadhyaya and R. M. German: Metall. Mater. Trans., 1998, vol. 29B, pp. 857-66.10.1007/s11663-998-0145-4 ↗
28. A. Upadhyaya and R. M. German: Metall. Mater. Trans., 1998, vol. 29A, pp. 2631-38.10.1007/s11661-998-0235-6 ↗
29. R. Smoluchowski: Sci., 1965, vol. 150, pp. 1025-6.10.1126/science.150.3699.1025 ↗
30. L. A. Taylor and T. T. Meek: J. Aerosp. Eng., 2005, vol., 18, no. 3, pp. 188-96.10.1061/(ASCE)0893-1321(2005)18:3(188) ↗
31. F. Ruess, J. Schaenzlin and H. Benaroya: J. Aerosp. Eng., 2006, vol. 19, no. 3, pp. 133-57.10.1061/(ASCE)0893-1321(2006)19:3(133) ↗
32. P. Lu, R. M. German and R. G. Iacocca: Metall. Mater. Trans., 2001, vol. 32A, pp. 2097-2107.10.1007/s11661-001-0021-1 ↗
33. J. L. Johnson, L. G. Campbell, S. J. Park and R. M. German: Metall. Mater. Trans., 2009, vol. 40A, pp. 426-37.10.1007/s11661-008-9745-5 ↗
34. A. Tewari, A. M. Gokhale and R. M. German: Acta Mater., 1999, vol. 47, pp. 3721-34.10.1016/S1359-6454(99)00164-0 ↗
35. R.M. German, S.J. Park, and J.L. Johnson: Proc. Sixteenth Int. Plansee Semin., vol. 2, G. Kneringer, P. Rodhammer, and H. Wildner, eds., Plansee Holdings, Reutte, Austria, 2005, pp. 672–83.
36. L. G. Campbell and R. M. German: Adv. Powder Metall. Part. Mater., 2007, part 8, pp. 29-43.
37. L.G. Campbell, J.L. Johnson, and R.M. German: Proc. Int. Plansee Seminar, vol. 1, P. Rodhammer, ed., Plansee Group, Reutte, Austria, 2009, pp. RM69.1–12.
38. Y. He. S. Yi and J. E. Smith: J. Mater. Sci., 2005, vol. 40, pp. 4067-75.10.1007/s10853-005-2798-6 ↗
39. Z. Xue, S. L. Noojin, J. G. Vanderfrift, A. K. Kuruvilla and J. E. Smith: Mater. Trans. JIM, 1996, vol. 37, pp. 1084-90.10.2320/matertrans1989.37.1084 ↗
40. Z. Xue, J.G. Vandergrift, A. Nadarajah, and J.E. Smith: Seventh Int. Symp. Exp. Methods Microgravity Mater. Sci., R.A. Schiffman, ed., TMS, Warrendale, PA, 1995, pp. 147–52.
41. S. Kohara and M. Hoshino: Adv. Powder Metall. Part. Mater., 1994, vol. 3, pp. 295-302.
42. A. Upadhyaya, R. G. Iacocca and R. M. German: J. Met., 1999, vol. 51, no. 4, pp. 37-40.
43. R. M. German, S. J. Park, J. L. Johnson and L. G. Campbell: Adv. Powder Metall. Part. Mater., 2005, part 10, pp. 296-307.
44. E.A. Lehtihet, I.J. Petrick, and R.C. Voigt: Dimensional Capabilities of Ferrous Powder Metal Components, Pennsylvania State Univ., University Park, PA, 2004.
45. R.M. German: Powder Metallurgy of Iron and Steel, Wiley, New York, NY, 1998, pp. 22–29.
46. S.J. Park, S.H. Chung, J.L. Johnson, and R.M. German: Adv. Powder Metall. Part. Mater., 2006, 5, pp. 14-24.
47. R. M. German, A. Bose and S. S. Mani: Metall. Trans., 1992, vol. 23A, pp. 211-9.10.1007/BF02660866 ↗
48. R. M. German and K. S. Churn: Metall. Trans., 1984, vol. 15A, pp. 747-54.10.1007/BF02644206 ↗
49. P. Marquardt and J. Schilz: Adv. Colloid Interface Sci., 1993, vol. 46, pp. 185-219.10.1016/0001-8686(93)80041-9 ↗