journal article·2012-01Open access

On the Processing of Martensitic Steels in Continuous Galvanizing Lines: Part 1

Taejin Song, Jaihyun Kwak, B. C. De Cooman

Abstract

Whereas low-carbon (< 0.2 mass pct) martensitic grades can be produced easily in continuous annealing processing lines equipped with the required cooling capacity, the thermal cycles in continuous galvanizing lines make it difficult to produce hot-dip Zn or Zn-alloy coated high-strength martensitic grades. This is because of the tempering processes occurring during dipping of the strip in the liquid Zn bath and, in the case of galvannealed sheet steel, the short thermal treatment required to achieve the alloying between the Zn and the steel. These short additional thermal treatments last less than 30 seconds but severely degrade the mechanical properties. Using a combination of internal friction, X-ray diffraction, and transmission electron microscopy, it is shown that the ultrafine-grained lath microstructure allows for a rapid dislocation recovery and carbide formation during the galvanizing processes. In addition, the effective dislocation pinning occurring during the galvannealing process results in strain localization and the suppression of strain hardening. ; open ; 1 ; 1 ; 2 ; 4 ; scie ; scopus
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (65)

Show source-provided references
1. B.D. Cullity and S.R. Stock: Elements of X-Ray Diffraction, Prentice Hall, Upper Saddle River, NJ, 2001, pp. 385–404.
2. T. Ungár: Scripta Mater., 2004, vol. 51, pp. 777–81.10.1016/j.scriptamat.2004.05.007 ↗
3. Á. Révész, T. Ungár, A. Borbély, and J. Lendvai: Nanostruct. Mater., 1996, vol. 7, pp. 779–88.10.1016/S0965-9773(96)00048-7 ↗
4. G. Roebben, B. Bollen, and A. Brebels: Rev. Sci. Instrum., 1997, vol. 68, pp. 4511–15.10.1063/1.1148422 ↗
5. J.H. Hollomon and L.D. Jaffe: Trans. AIME, 1945, vol. 162, pp. 223–49.
6. G.R. Speich and W.C. Leslie: Metall. Trans., 1972, vol. 3, pp. 1043–54.10.1007/BF02642436 ↗
7. M. Sarikaya, A.K. Jhingan, and G. Thomas: Metall. Trans. A, 1983, vol. 14A, pp. 1121–33.10.1007/BF02670450 ↗
8. H.K.D.H. Bhadeshia and D.V. Edmonds: Met. Sci., 1979, vol. 13, pp. 325–34.
9. F. Zia-Ebrahimi and G. Krauss: Acta Metall., 1984, vol. 32, pp. 1767–78.10.1016/0001-6160(84)90233-5 ↗
10. J. Pietikäinen: Mater. Sci. Eng. A, 1999, vols. 273–275, pp. 466–70.10.1016/S0921-5093(99)00329-9 ↗
11. F. Zia-Ebrahimi and G. Krauss: Metall. Trans. A, 1983, vol. 14A, pp. 1109–19.10.1007/BF02670449 ↗
12. G. Krauss: ISIJ Int., 1995, vol. 35, pp. 349–59.10.2355/isijinternational.35.349 ↗
13. G. Krauss: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 861–77.10.1007/s11661-001-0344-y ↗
14. G. Thomas: Metall. Trans. A, 1978, vol. 9A, pp. 439–50.10.1007/BF02646396 ↗
15. P.M. Kelly, A. Jostsons, and R.G. Blake: Acta Metall. Mater., 1990, vol. 38, pp. 1075–81.10.1016/0956-7151(90)90180-O ↗
16. S. Morito, H. Tanaka, R. Konishi, T. Furuhara, and T. Maki: Acta Mater., 2003, vol. 51, pp. 1789–99.10.1016/S1359-6454(02)00577-3 ↗
17. T. Maki: Proc. of the 1st Int. Symp. on Steel Science (ISSS 2007), Kyoto, Japan, 2007, pp. 1–10.
18. S. Morito, H. Yoshida, T. Maki, and X. Huang: Mater. Sci. Eng. A, 2006, vols. 438–440, pp. 237–40.10.1016/j.msea.2005.12.048 ↗
19. S. Morito, X. Huang, T. Furuhara, T. Maki, and N. Hansen: Acta Mater., 2006, vol. 54, pp. 5323–31.10.1016/j.actamat.2006.07.009 ↗
20. H. Kitahara, R. Ueji, N. Tsuji, and Y. Minamino: Acta Mater., 2006, vol. 54, pp. 1279–88.10.1016/j.actamat.2005.11.001 ↗
21. E.J. Fasiska and G.A. Jeffrey: Acta Cryst., 1965, vol. 19, pp. 463–71.10.1107/S0365110X65003602 ↗
22. W.C. Leslie, R.M. Fisher, and N. Sen: Acta Metall., 1959, vol. 7, pp. 632–44.10.1016/0001-6160(59)90133-6 ↗
23. M.G.H. Wells: Acta Metall., 1964, vol. 12, pp. 389–99.10.1016/0001-6160(64)90009-4 ↗
24. M.X. Zhang and P.M. Kelly: Acta Mater., 1998, vol. 46, pp. 4081–91.10.1016/S1359-6454(98)00046-9 ↗
25. F.-G. Wei and K. Tsuzaki: Acta Mater., 2005, vol. 53, pp. 2419–29.10.1016/j.actamat.2005.02.004 ↗
26. R. Bagramov, D. Mari, and W. Benoit: Phil. Mag. A, 2001, vol. 81, pp. 2797–2808.10.1080/01418610108217165 ↗
27. M. Weller: J. Phys. (Paris), Colloque, 1983, vol. 44, pp. 63–82.
28. I. Tkalcec and D. Mari: Mater. Sci. Eng. A, 2004, vol. 370, pp. 213–17.10.1016/j.msea.2003.04.004 ↗
29. I. Tkalcec, D. Mari, and W. Benoit: Mater. Sci. Eng. A, 2006, vol. 442, pp. 471–75.10.1016/j.msea.2006.03.115 ↗
30. Y. Liu: Acta Metall. Mater., 1993, vol. 41, pp. 3277–87.10.1016/0956-7151(93)90057-Y ↗
31. M. Weller: J. Phys. IV France, 1995, vol. 5, pp. 199–204.10.1051/jp4:1995721 ↗
32. W. Pascheto and G.P. Hohari: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2461–69.10.1007/BF02652340 ↗
33. F. Walz, M. Weller, and M. Hirscher: Phys. Status Solidi (A) Appl. Res., 1996, vol. 154, pp. 765–78.10.1002/pssa.2211540230 ↗
34. M. Weller: J. Phys. (Paris), Colloques, 1985, vol. 46, pp. 7–14.
35. L.B. Magalas, P. Moser, and I.G. Ritchie: J. Phys. (Paris), Colloque, 1983, vol. 44, pp. 645–49.
36. M.S. Blanter, I.S. Golovin, H. Neuhäuser, and H.-R. Sinning: Internal Friction in Metallic Materials: A Handbook, Springer, Berlin, Germany, 2007, pp. 71–73.10.1007/978-3-540-68758-0 ↗
37. K. Takita and K. Sakamoto: Scripta Metall., 1976, vol. 10, pp. 399–403.10.1016/0036-9748(76)90160-5 ↗
38. A. Seeger: Phys. Status Solidi (A), 1979, vol. 55, pp. 457–68.10.1002/pssa.2210550213 ↗
39. I. Tkalcec: Ph.D. Dissertation, École Polytechnique Federal De Lausanne, Switzerland, 2004, pp. 51–73.
40. J.J. Hoyos, A.A. Ghilarducci, H.R. Salva, C.A. Chaves, and J.M. Vélez: Mater. Sci. Eng. A, 2009, vols. 521–522, pp. 347–50.10.1016/j.msea.2008.09.088 ↗
41. B.P.J. Sandvik and C.M. Wayman: Metall. Trans. A, 1983, vol. 14A, pp. 809–22.10.1007/BF02644284 ↗
42. A. Shibata, S. Morito, T. Furuhara, and T. Maki: Scripta Mater., 2005, vol. 53, pp. 597–602.10.1016/j.scriptamat.2005.04.023 ↗
43. J.C. Shyne and W.D. Nix: Acta Metall., 1965, vol. 13, pp. 869–70.10.1016/0001-6160(65)90151-3 ↗
44. G. Thomas and Y.-L. Chen: Metall. Trans. A, 1981, vol. 12A, pp. 933–49.10.1007/BF02643474 ↗
45. B.L. Bramfitt and J.G. Speer: Metall. Trans. A, 1990, vol. 21A, pp. 817–29.10.1007/BF02656565 ↗
46. G.R. Speich: Trans. TMS-AIME, 1969, vol. 245, pp. 2553–64.
47. J. Wilde, A. Cerezo, and G.D.W. Smith: Scripta Mater., 2000, vol. 43, pp. 39–48.10.1016/S1359-6462(00)00361-4 ↗
48. S.J. Barnard, G.D.W. Smith, M. Sarikaya, and G. Thomas: Scripta Metall., 1981, vol. 15, pp. 387–92.10.1016/0036-9748(81)90216-7 ↗
49. M. Tang, L.P. Kubin, and G.R. Canova: Acta Mater., 1998, vol. 46, pp. 3221–35.10.1016/S1359-6454(98)00006-8 ↗
50. J.W. Christian: Metall. Trans. A, 1983, vol. 14A, pp. 1237–56.10.1007/BF02664806 ↗
51. K. Nakashima, Y. Fujimura, H. Matsubayashi, T. Tsuchiyama, and S. Takaki: Proc. of the 1st Int. Symp. on Steel Science (ISSS 2007), Kyoto, Japan, 2007, pp. 215–28.
52. Y. Estrin and L.P. Kubin: Continuum Models for Materials with Microstructure, 1995, pp. 395–450.
53. G.T. Hahn: Acta Metall., 1962, vol. 10, pp. 727–38.10.1016/0001-6160(62)90041-X ↗
54. F. Louchet, L.P. Kubin, and D. Vesely: Phil. Mag. A, 1979, vol. 39, pp. 433–54.10.1080/01418617908239283 ↗
55. H.B. Sun, F. Yoshida, X. Ma, T. Kamei, and M. Ohmori: Mater. Lett., 2003, vol. 57, pp. 3206–10.10.1016/S0167-577X(03)00036-3 ↗
56. N. Tsuchida, Y. Tomota, K. Nagai, and K. Fukaura: Scripta Mater., 2006, vol. 54, pp. 57–60.10.1016/j.scriptamat.2005.09.011 ↗
57. J.M. Chilton and P.M. Kelly: Acta Metall., 1968, vol. 16, pp. 637–56.10.1016/0001-6160(68)90137-5 ↗
58. S. Okamoto, D.K. Matlock, and G. Krauss: Scripta Metall. Mater., 1991, vol. 25, pp. 39–44.10.1016/0956-716X(91)90350-A ↗
59. G. Schoeck and A. Seeger: Acta Metall., 1959, vol. 7, pp. 469–77.10.1016/0001-6160(59)90028-8 ↗
60. T. Swarr and G. Krauss: Metall. Trans. A, 1976, vol. 7A, pp. 41–48.10.1007/BF02644037 ↗
61. R.B. Nicholson, G. Thomas, and J. Nutting: Acta Metall., 1960, vol. 8, pp. 172–76.10.1016/0001-6160(60)90125-5 ↗
62. C.A. Apple, R.N. Caron, and G. Krauss: Metall. Trans., 1974, vol. 5, pp. 593–99.10.1007/BF02644654 ↗
63. T. Ohmura, K. Tsuzaki, and S. Matsuoka: Scripta Mater., 2001, vol. 45, pp. 889–94.10.1016/S1359-6462(01)01121-6 ↗
64. T. Ohmura and K. Tsuzaki: Proc. of the 1st Int. Symp. on Steel Science (ISSS 2007), Kyoto, Japan, 2007, pp. 35–46.10.2320/materia.46.251 ↗
65. S. Takaki, K. Takeda, N. Nakada, and T. Tsuchiyama: Proc. of 1st Int. Conf. on Interstitially Alloyed Steels (IAS 2008), Pohang, South Korea, 2008, pp. 107–13.