Investigation of the Effect of Tungsten Substitution on Microstructure and Abrasive Wear Performance of In Situ VC-Reinforced High-Manganese Austenitic Steel Matrix Composite
Source abstract
Abstract
Particulate VC-reinforced high-manganese austenitic steel matrix composites with different vanadium and tungsten contents were synthesized by conventional alloying and casting route. Microstructural characterizations showed that the composites processed by in situ precipitation of the reinforcements were composed of V8C7 particulates distributed in an austenitic matrix. It was observed that addition of tungsten to austenite increases work-hardening rate of subsurface layer during pin-on disk wear test. The maximum abrasive wear resistance was achieved at tungsten content equal to 2 wt pct. However, excessive addition of tungsten promoted the formation of W3C phase and reduced the abrasive wear resistance because of decrease in distribution homogeneity and volume fraction of the reinforcing VC particles.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. K. Das, T.K. Bandyopadhyay and S. Das: J. Mater. Sci., 2002, vol. 37, pp. 3881–92.10.1023/A:1019699205003 ↗
2. W.H. Jiang, W.D. Pan, Y.L. Ren and X.L. Han: J. Mater. Sci. Lett., 1998, vol. 17, pp. 1527–29.10.1023/A:1006529307807 ↗
3. E. Pagounis and V.K. Lindroos: Mater. Sci. Eng. A, 1998, vol. A 246, pp. 221–34.10.1016/S0921-5093(97)00710-7 ↗
4. T.K. Bandyopadhyay, S. Chatterjee and K. Das: J. Mater. Sci., 2004, vol. 39, pp. 5735–42.10.1023/B:JMSC.0000040083.98097.c3 ↗
5. T.K. Bandyopadhyay and K. Das: J. Mater. Sci., 2004, vol. 39, pp. 6503–08.10.1023/B:JMSC.0000044889.38392.1d ↗
6. K. Das and T.K. Bandyopadhyay: Mater. Lett., 2004, vol. 58, pp. 1877–80.10.1016/j.matlet.2003.11.034 ↗
7. A.K. Srivastava and K. Das: Mater. Sci. Eng. A, 2009, vol. A 516, pp. 1–6.10.1016/j.msea.2009.04.041 ↗
8. S. Wei, J. Zhua and I. Xua: Tribol. Int., 2006, vol. 39, pp. 641–48.10.1016/j.triboint.2005.04.035 ↗
9. S. Wei, J. Zhua, I. Xua and L. Rui: Mater. Des., 2006, vol. 27, pp. 58–63.10.1016/j.matdes.2004.09.027 ↗
10. K. Tokaji, Y. Uematsu, T. Horie and Y. Takahashi: Mater. Sci. Eng. A, 2006, vol. A 418, pp. 326–34.10.1016/j.msea.2005.12.007 ↗
11. Y. Uematsu, K. Tokaji, T. Horie and K.Nishigaki: Mater. Sci. Eng. A, 2007, vol. A 471, pp. 15–21.10.1016/j.msea.2007.04.070 ↗
12. K. Shimizu, T. Naruse, Y. Xinba, K. Kimura, K. Minami and H. Matsumoto: Wear, 2009, vol. 267, pp. 104–09.10.1016/j.wear.2008.12.086 ↗
13. Y. Uematsu, K. Tokaji, K. Nishigaki, D. Okajima and M. Ogasawara: Mater. Sci. Eng. A, 2010, vol. A 527, pp. 2621–28.10.1016/j.msea.2010.01.067 ↗
14. L. Xu, S. Wei, J. Xing, Y. Li and R. Long: Met. Mater. Int., 2006, vol. 12, no. 5, pp. 371–75.10.1007/BF03027702 ↗
15. E.G. Moghaddam, N. Varahram and P. Davami: Mater. Sci. Eng. A, 2012, vol. A 532, pp. 260–66.10.1016/j.msea.2011.10.089 ↗
16. S.H. Mousavi Anijdan, A. Bahrami, N. Varahram and P. Davami: Mater. Sci. Eng. A, 2007, vol. A 454–455, pp. 623–628.10.1016/j.msea.2006.11.128 ↗
17. G. Roberts, G. Krauss and R. Kennedy: Tool steels, fifth ed., ASM International, Materials Park, OH, 1998, p. 283.10.31399/asm.tb.ts5.9781627083584 ↗
18. ASM Handbook, Vol 3: Alloy Phase Diagrams, ASM International, Materials Park, OH, 1992.
19. T.S. Eyre: Tribol. Int., 1976, vol. 9, no. 5, pp. 203–12.10.1016/0301-679X(76)90077-3 ↗
20. ASTM E-23-2a, Standard Test Methods for Notched Bar Impact Testing of Metallic Materials, Annual Book of ASTM Standards, vol. 0.3.01, 1998.
21. ASM Handbook, Vol 1: Properties and Selection: Irons, Steels, and High-Performance Alloys, ASM International, Materials Park, OH, 2005.
22. J.H. Davidson: Microstructure of Steels and Cast Irons, Springer, New York, 2004, p. 264.
23. W.B. MacKay and R.W. Smith: US Patent No. 4377422, 1983.
24. A.G. Rakhshtadt, K.A. Lanskaya and V.V. Goryachev: Metallovedenie i Termicheskaya Obrabotka Metallov, 1981, vol. 2, pp. 21–25.
25. V.M. Kardonskii and O.V. Samoilova: Metallovedenie i Termicheskaya Obrabotka Metallov, 1990, vol. 8, pp. 59–61.
26. A.G. Rakhshtadt, K.A. Lanskaya, N.M. Suleimanov and L.V. Katkova: Metallovedenie i Termicheskaya Obrabotka Metallov, 1975, vol. 6, pp. 23–27.
27. A.S. Chaus: Met. Sci. Heat. Treat., 1998, vol. 40, pp. 15–20.10.1007/BF02466219 ↗
28. A.S. Chaus: Met. Sci. Heat. Treat., 2003, vol. 45, pp. 3–7.10.1023/A:1025997100645 ↗
29. H. Fua, Q. Xiao and Y. Li: Mater. Sci. Eng. A, 2005, vol. A 395, pp. 281–87.10.1016/j.msea.2004.12.029 ↗
30. A.S. Chaus: Met. Sci. Heat. Treat., 2005, vol. 47, pp. 16–21.10.1007/s11041-005-0031-5 ↗
31. A.S. Chaus: Phys. Met. Metallogr., 2008, vol. 106, pp. 82–89.10.1134/S0031918X08070119 ↗
32. A.K. Srivastava and K. Das: Tribol. Int., 2010, vol. 43, pp. 944–50.10.1016/j.triboint.2009.12.057 ↗
33. B.G. Mellor: Surface Coatings for Protection Against Wear, Woodhead, Cambridge, 2006, p. 132.10.1533/9781845691561 ↗
34. N.J. Archer and K.K. Yee: Wear, 1978, vol. 48, pp. 237–50.10.1016/0043-1648(78)90222-3 ↗