journal article·2013-01

Effects of Deformation Behavior and Processing Temperature on the Fatigue Performance of Deep-Rolled Medium Carbon Bar Steels

M. D. Richards, M. E. Burnett, J. G. Speer, D. K. Matlock

Publisher page

Abstract

The effects of processing temperature on the deep-rolling response of three medium carbon bar steels, a quenched and tempered 4140 alloy, a 0.34C, 1.21Mn, 0.66Si nontraditional bainitic alloy, and a 0.36C, 1.37Mn V-microalloyed ferrite plus pearlite steel, was assessed through bending fatigue. The significantly different deformation behaviors of the three alloys were characterized through standard and nonstandard quasi-static and cyclic uniaxial tension and compression tests at room temperature (RT) and in situ at temperatures up to 634 K. Deep rolling, performed at RT and at elevated temperature (HT) in the dynamic strain-aging (DSA) regime, increased measured endurance limits by 51-62 pct (RT) and 96-117 pct (HT) as compared with the baseline condition. The enhanced fatigue performance by RT deep rolling primarily reflected the effects of the introduction of favorable residual stresses. The improved fatigue performance from HT deep rolling was attributed to the enhanced resistance to strain reversal of the material deformed during deep rolling, due to a change in deformation mechanism from dislocation-interstitial interactions in the DSA regime during processing, which inhibited mechanically induced relaxation of residual stress during cyclic loading.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Microstructure and Mechanical Properties of Steels · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. “The World’s Top 10 Best Engines Use Steel: Analysis of Ward’s AutoWorld Top 10 Best Engine List for 2004,” American Iron and Steel Institute, Retrieved Feb. 12, 2008, from www.autosteel.org.
2. H. Naumann: Deep Rolling of Highly Stressed Components, American Society of Tool and Manufacturing Engineers, Technical Paper no. MF68-169, 1968, pp. 1–7.
3. E. Randlett: Deep Rolling of Crankshaft, Society of Manufacturing Engineers (SME), Material Forming Report no. MF70-262, 1970.
4. H.J. Naumann: Metalworking, 1968, vol. 24, no. 2, pp. 48–50.
5. K.H. Kloos, B. Fuchsbauer, and J. Adelmann: Int. J. Fatigue, 1987, vol. 9, pp. 35–42.10.1016/0142-1123(87)90087-9 ↗
6. G.N.J. Gilbert and K.B. Palmer: The Influence of Surface Rolling on the Fatigue Properties of Flake Graphite and Nodular Graphite Cast Irons, British Cast Iron Research Association (B.C.I.R.A.) Research Report No. 392, 1954, pp. 447–64.
7. E. Broszeit, H. Steindorf, and G. Schlieper: in Proceedings of the 1986 International Powder Metallurgy Conference, Verlag Schmid, Dusseldorf, FRG, 1986, pp. 403–06.
8. K.H. Kloos, E. Broszeit, B. Fuchsbauer, and F. Schmidt: Zeitschrift Fur Werkstofftechnik, 1981, vol. 12, pp. 359–65.10.1002/mawe.19810121007 ↗
9. K.H. Kloos and J. Adelmann: J. Mech. Behav. Mater. (U.K.), 1989, vol. 2, pp. 75–86.10.1515/JMBM.1989.2.1-2.75 ↗
10. B. Fuchsbauer: Dr.-Ing. Dissertation, Von dem Fachbereich Maschinenbau an der Technischen Hochschule Darmstadt, 1983.
11. A. Drechsler, T. Dörr, and L. Wagner: Mater. Sci. Eng. A, 1998, vol. 243, pp. 217–20.10.1016/S0921-5093(97)00804-6 ↗
12. L. Wagner: Mater. Sci. Eng. A, 1999, vol. 263, pp. 210–16.10.1016/S0921-5093(98)01168-X ↗
13. T. Watmough and M.J. Malatesta: Trans. Am. Foundrymen’s Soc., 1984, vol. 92, pp. 83–99.
14. F. Galzy, H. Michaud, and J.M. Sprauel: Mater. Sci. Forum, 2005, vols. 490–491, pp. 384–89.10.4028/www.scientific.net/MSF.490-491.384 ↗
15. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill, New York, 1986, pp. 408–12.
16. J. Bauschinger: Civilingenieur, 1881, vol. 27, pp. 289–348.
17. L. Zhonghua and G. Haicheng: Metall. Trans. A, 1990, vol. 21A, pp. 717–24.10.1007/BF02671942 ↗
18. R.C. Daniel and G.T. Horne: Metall. Trans., 1971, vol. 2, pp. 1161–72.10.1007/BF02664248 ↗
19. A. Aran and M. Demirkol: Mater. Sci. Eng., 1981, vol. 47, pp. 89–92.10.1016/0025-5416(81)90212-3 ↗
20. A. Goel, R.K. Ray, and G.S. Murty: Scripta Metall., 1983, vol. 17, pp. 375–80.10.1016/0036-9748(83)90176-X ↗
21. R.E. Stoltz and R.M. Pelloux: Metall. Trans. A, 1976, vol. 7A, pp. 1295–1306.10.1007/BF02658814 ↗
22. Y.M. Yaman, A. Özsoy, and K. Taşci: J. Mater. Sci. Lett., 1990, vol. 9, pp. 429–31.10.1007/BF00721020 ↗
23. R.E. Stoltz and R.M. Pelloux: Scripta Metall., 1974, vol. 8, pp. 269–76.10.1016/0036-9748(74)90250-6 ↗
24. D.V. Wilson and P.S. Bate: Acta Metall., 1986, vol. 34, no. 6, pp. 1107–20.10.1016/0001-6160(86)90221-X ↗
25. P.B. Prangnell, T. Downes, P.J. Withers, and T. Lorentzen: Mater. Sci. Eng. A, 1995, vol. 197, pp. 215–21.10.1016/0921-5093(94)09744-5 ↗
26. J.D. Embury: in Strengthening Methods in Crystals, A. Kelly and R.B. Nicholson, ed., Halstead Press, New York, 1971, pp. 331–402.
27. A. Abel and R.K. Ham: Acta Metall., 1966, vol. 14, pp. 1489–94.10.1016/0001-6160(66)90170-2 ↗
28. D.V. Wilson: Acta Metall., 1965, vol. 13, pp. 807–14.10.1016/0001-6160(65)90145-8 ↗
29. J.C. Fisher, E.W. Hart, and R.H. Pry: Acta Metall., 1953, vol. 1, pp. 336–39.10.1016/0001-6160(53)90109-6 ↗
30. E. Orowan: in Internal Stresses and Fatigue in Metals, G.M. Rassweiler and W.L. Grube, ed., Elsevier, London, 1959.
31. A. Plumtree and H.A. Abdel-Raouf: Int. J. Fatigue, 2001, vol. 23, pp. 799–805.10.1016/S0142-1123(01)00037-8 ↗
32. D.K. Matlock, M.D. Richards, and J.G. Speer: Mater. Sci. Forum, 2010, vols. 638–642, pp. 142–47.10.4028/www.scientific.net/MSF.638-642.142 ↗
33. M.D. Richards: Ph.D. Thesis, No. T-6595, Colorado School of Mines, Golden, 2008.
34. A. Zeren and M. Zeren: J. Mater. Process. Technol., 2003, vol. 141, pp. 86–92.10.1016/S0924-0136(03)00131-6 ↗
35. D.J. Dingley and D. McLean: Acta Metall., 1967, vol. 15, pp. 885–901.10.1016/0001-6160(67)90371-9 ↗
36. A. Wick, V. Schulze, and O. Vöhringer: Mater. Sci. Eng. A, 2000, vol. A293, pp. 191–97.10.1016/S0921-5093(00)01035-2 ↗
37. R. Menig, V. Shulze, and O. Vöhringer: Mater. Sci. Eng. A, 2002, vol. A335, pp. 198–206.10.1016/S0921-5093(01)01915-3 ↗
38. P. Juijerm and I. Altenberger: J. Met. Mater. Miner., 2007, vol. 17, pp. 37–41.
39. I. Altenberger, I. Nikitin, and B. Scholtes: in Proceedings of the 9th International Conference of Shot Peening, V. Schulze and A. Kiku-Lari, ed., IITI International, Paris, France, 6–9 September 2005, pp. 253–60.
40. I. Altenberger: in Proceedings of the 9th International Conference of Shot Peening, V. Schulze and A. Kiku-Lari, ed., IITI International, Paris, France, 6–9 September 2005, pp. 144–55.
41. I. Nikitin, I. Altenberger, and B. Scholtes: in Proceedings of the 9th International Conference of Shot Peening, V. Schulze and A. Kiku-Lari, ed., IITI International, Paris, France, 6–9 September 2005, pp. 185–90.
42. P. Juijerm and I. Altenberger: Scripta Mater., 2007, vol. 56, pp. 285–88.10.1016/j.scriptamat.2006.10.017 ↗
43. W.C. Leslie: The Physical Metallurgy of Steels, 3rd ed., McGraw-Hill, New York, 1981, p. 91.
44. J.W. Edington and R.E. Smallman: Acta Metall., 1964, vol. 12, pp. 1313–28.10.1016/0001-6160(64)90120-8 ↗
45. J.G. Morris: Mater. Sci. Eng., 1974, vol. 13, pp. 101–08.10.1016/0025-5416(74)90177-3 ↗
46. S. Okamoto, D.K. Matlock, and G. Krauss: Scripta Metall. Mater., 1991, vol. 25, pp. 39–44.10.1016/0956-716X(91)90350-A ↗
47. C.-C. Li, J.D. Flasck, J.A. Yaker, and W.C. Leslie: Metall. Trans. A, 1978, vol. 9A, pp. 85–89.
48. M.D. Richards, C.J. Van Tyne and D.K. Matlock: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7926–32.10.1016/j.msea.2011.07.015 ↗
49. D.K. Matlock, G. Krauss, and J.G. Speer: J. Mater. Process. Technol., 2001, vol. 117, pp. 324–28.10.1016/S0924-0136(01)00792-0 ↗
50. B.B. Cullity: Elements of X-Ray Diffraction, 2nd ed., Addison-Wesley Publishing Co, Reading, 1978, pp. 411–15, 447–69.
51. R.J. Love and D.N. Waistall: “The Improvement in the Bending Fatigue Strength of Production Crankshafts by Cold Rolling,” Motor Industry Research Association (MIRA) Report No. 1954/2, Nov. 1954.
52. H. Michuad, J.M. Sprauel, and F. Galzy: Mater. Sci. Forum, 2006, vols. 524–525, pp. 45–49.10.4028/www.scientific.net/MSF.524-525.45 ↗
53. M.D. Richards, D.K. Matlock, and J.G. Speer: SAE Technical Publication #2004-01-1528, SAE, Warrendale, 2004.
54. H.O. Fuchs and R.I. Stephens: Metal Fatigue in Engineering, John Wiley & Sons, New York, 1980, p. 69.
55. G.B. Olson: in Deformation Processing and Structure, G. Krauss, ed., American Society for Metals, Metals Park, 1984, pp. 391–424.