journal article·2002-09

Crack growth in a nearly fully-lamellar gamma TiAl alloy at 650 °C and 800 °C under constant load conditions

Young-Won Kim, Kumar V. Jata

Publisher page

Abstract

The crack growth behavior of a gamma titanium aluminide alloy, K5S, was investigated at 650 °C and 800 °C under constant load conditions in a nearly fully-lamellar microstructural form. Crack growth at both temperatures ensues at stress intensities (K) much higher than anticipated from the R curves. At 650 °C, creep crack extension occurs through the formation of microcracks (interlamellar (IL) separation) and their joining to the main crack tip through ligament fracture. This results in a mainly transgranular (TG) fracture with occasional IL separation. This process features a rapid initial crack growth but at decreasing growth rate, followed by a nearly no-growth stage. At 800 °C, crack extension is accompanied by extensive plastic deformation and consists of an initial rapid transition period and a subsequent steady state. For similar K’s, crack extension and growth rate are greater at 800 °C than at 650 °C, but even these are very slow processes for this alloy. The resistance to crack propagation at 650 °C is explained in terms of work hardening that arises during the extended primary creep deformation occurring ahead of the crack tip. Increased crack propagation at 800 °C is accredited to grain boundary and lamellar-interface weakening and extensive post primary creep damage in the plastic zone. The resulting fracture at 800 °C is mainly boundary fracture, which consists of IG fracture involving formation and coalescence of voids, and IL separation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Y-W. Kim: JOM, 1994, July, pp. 30–39.10.1007/BF03220745 ↗
2. Y-M. Kim: Acta Metall. Mater., 1992, vol. 40 (6), pp. 1121–34.10.1016/0956-7151(92)90411-7 ↗
3. Y-W. Kim and D.M. Dimiduk: in Structural Intermetallics 1997, M.V. Nathal et al., eds., TMS, Warrendale, PA, 1997, pp. 531–43.
4. Y-W. Kim and D.M. Dimiduk: in Cleavage Fracture: Theory, Experimental, and Modeling, K.S. Chan, ed., TMS, Warrendale, PA, 1997, pp. 305–17.
5. Y-W. Kim: J. Mater. Sci. Eng., 1995, vol. A192, pp. 519–33.10.1016/0921-5093(94)03271-8 ↗
6. J. Kumpfert, Y-W. Kim, and D.M. Dimiduk: J. Mater. Sci. Eng., 1995, vols. A192–A193, pp. 463–73.
7. K.T.V. Rao, Y-W. Kim, C.L. Muhlstein, and R.O. Ritchie: J. Mater. Sci. Eng., 1995, vols. A192–A193, pp. 474–82.
8. A.H. Rosenberger, B.D. Worth, and J.M. Larsen: in Structural Intermetallics 1997, M.V. Nathal, R. Darolia, et al., eds., TMS, Warrendale, PA, 1997, pp. 555–62.
9. K.S. Chan and Y-W. Kim: Metall. Trans. A, 1992, vol. 23A, pp. 1663–77.10.1007/BF02804362 ↗
10. K.S. Chan and Y-W. Kim: Metall. Trans. A, 1993, vol. 24A, pp. 113–25.10.1007/BF02669609 ↗
11. K. Chan and Y-W. Kim: Acta Metall. Mater., 1995, vol. 43, pp. 439–51.10.1016/0956-7151(94)00278-P ↗
12. G.A. Webster and R.A. Ainsworth: High Temperature Component Life Assessment, Chapman and Hall, London, 1994.10.1007/978-94-017-1771-7 ↗
13. S. Floreen and R.H. Kane: Fatigue Fract. Mater. Struct., 1979, vol. 2, pp. 401–12.10.1111/j.1460-2695.1979.tb01097.x ↗
14. K. Sadananda and K.V. Jata: Metall. Trans. A, 1988, vol. 19A, pp. 847–54.10.1007/BF02628367 ↗
15. B. Dogan, A. Saxon, and K.-H. Schwalbe: Mater. High Temp., 1992, vol. 10 (2), pp. 138–43.10.1080/09603409.1992.11689411 ↗
16. K.M. Nikbin, D.J. Smith, and G.A. Webster: Proc. R. Soc., 1984, vol. A.396, pp. 183–97.
17. G.A. Webster: Int. J. Pressure Vessels Piping, 1992, vol. 50, pp. 133–45.10.1016/0308-0161(92)90034-D ↗
18. A. Saxena: in ASTM STP 905, J.H. Underwood et al., eds., ASTM, Philadelphia, PA, 1986, pp. 185–201.
19. A.T. Yokobori and T. Yokobori: Eng. Fract. Mech., 1988, vol. 31, pp. 931–45.10.1016/0013-7944(88)90204-4 ↗
20. B. Dogan and K.-H. Schwalbe: in ASTM STP 1131, H.A. Ernst, A. Saxena, and D.L. McDowell, eds., ASTM, Philadelphia, PA, 1992, vol. 1, pp. 284–96.
21. ASTM E1457-00, ASTM, Philadelphia, PA, 2001, vol. 03.01, pp. 937–50.
22. H. Riedel and J.R. Rice: in ASTM STP 700, P.C. Paris, ed., ASTM, Philadelphia, PA, 1980, pp. 112–30.
23. O. Kwon, K.M. Nikbin, G.A. Webster, and K.V. Jata: Eng. Fract. Mech., 1999, in press.
24. K.V. Jata, D. Maxwell, and T. Nicholas: J. Eng. Mater. Technol., 1994, vol. 116, pp. 45–53.10.1115/1.2904254 ↗
25. Y-W. Kim and D.M. Dimiduk: U.S. Patent 5,558,729, Sept. 24, 1996
26. R.W. Evans and B. Wilshire: Creep of Metals and Alloys, Institute of Metals, London, 1985, pp. 69–72.
27. S.W. Schwenker and Y-W. Kim: in Gamma Titanium Aluminides, Y-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 985–92.
28. Y-W. Kim: Air Force Research Laboratory, Wright Patterson AFB, OH, unpublished research, 2000.
29. J. Beddoes, W. Wallace, and L. Zhao: Int. Mater. Rev., 1995, vol. 40 (5), pp. 197–217.10.1179/imr.1995.40.5.197 ↗
30. D.Y. Seo, T.R. Bieler, S.U. An, and D.E. Larsen: Mater. Trans., 1998, vol. 29A, p. 89.10.1007/s11661-998-0161-7 ↗
31. T.R. Bieler, D.Y. Seo, T.R. Everard, and P.A. McQuay: in Creep Behavior of Advanced Materials for 21st Century, R.S. Mishra, A.K. Mukherjee, and K.L. Murty, eds., TMS, Warrendale, PA, 1999, pp. 181–96.