Weldability Evaluation of a Cu-Bearing High-Strength Blast-Resistant Steel
Source abstract
Abstract
BlastAlloy160 (BA-160) steel, with a nominal composition of Fe-0.05C-3.65Cu-6.5Ni-1.84Cr-0.6Mo-0.1V (wt pct), is strengthened by Cu-rich precipitates and M2C carbides. This alloy was subjected to several weldability tests to assess its susceptibility to certain weld cracking mechanisms. Hot ductility testing revealed a liquation cracking temperature range (LCTR) of 148 K (–125 °C), which suggested moderate susceptibility to heat-affected zone (HAZ) liquation cracking. The enrichment of Ni and Cu was measured along the prior austenite grain boundaries in the simulated partially melted zone (PMZ) and was consistent with similar enrichment at interdendritic boundaries of the simulated fusion zone (FZ). Good wetting and penetration of liquid films along the austenite grain boundaries of the PMZ was also observed. Associated with that finding were thermodynamic calculations indicating a completely austenitic (face-centered cubic) microstructure at elevated temperatures. In testing to determine reheat cracking susceptibility, ductility values of 41 to 78 pct RA were established for the 723 K to 973 K (450 °C to 700 °C) temperature range. The good ductility values precluded susceptibility to reheat cracking according to the test criterion. Dilatometric measurements and thermodynamic calculations revealed the formation of austenite in the reheat cracking temperature range, which was attributed to the high Ni content of the BA-160 alloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. A. Saha and G.B. Olson: J. Comput.-Aided Mater. Des., 2007, vol. 14, no. 2, pp. 177-200.10.1007/s10820-006-9031-z ↗
2. A. Saha, J. Jung, and G.B. Olson: J. Comput.-Aided Mater. Des., 2007, vol. 14, no. 2, pp. 201-33.10.1007/s10820-006-9032-y ↗
3. J.L. Caron, S.S. Babu, and J.C. Lippold: Metall. Mater. Trans. A. DOI:10.1007/s11661-011-0801-1.10.1007/s11661-011-0801-1 ↗
4. X. Yu, J.L. Caron, S.S. Babu, J.C. Lippold, D. Isheim, and D.N. Seidman: Acta Mater., 2010, vol. 58, pp. 5596-5609.10.1016/j.actamat.2010.06.031 ↗
5. B. Weiss, G.E. Grotke, and R. Stickler: Weld. J., 1970, vol. 49, no. 10, pp. 471s-487s.
6. E.F. Nippes, W.F. Savage, B.J. Bastian, H.F. Mason, and R.M. Curran: Weld. J., 1955, vol. 34, no. 4, pp. 183s-193s.
7. R.D. Campbell and D.W. Walsh: ASM Handbook, 10th ed., ASM International, Materials Park, OH, 1993, vol. 6, pp. 603–13.
8. J.C. Lippold and D.J. Kotecki: Welding Metallurgy and Weldability of Stainless Steels, Wiley, Inc., Hoboken, NJ, 2005, pp. 319-22.
9. X. Yu, J.L. Caron, S.S. Babu, J.C. Lippold, D. Isheim, and D.N. Seidman: Metall. Mater. Trans. A, in press.
10. A. Dhooge and A. Vinckier: Weld. World, 1992, vol. 30, nos. 3/4, pp. 44-71.
11. C.D. Lundin and K.K. Khan: Weld. Res. Counc. Bull., 1996, no. 409, pp. 1–117.
12. J.G. Nawrocki, J.N. DuPont, C.V. Robino, and A.R. Marder: Weld. J., 2000, vol. 79, no. 12, pp. 355s-362s.
13. J.P. Balaguer, Z. Wang, and E.F. Nippes: Weld. J., 1989, vol. 68, no. 4, pp. 121s-131s.
14. J.G. Nawrocki, J.N. DuPont, C.V. Robino, and A.R. Marder: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2585-94.10.1007/s11661-001-0048-3 ↗
15. J. Shin and C.J. McMahon Jr.: Acta. Metall., 1984, vol. 32, pp. 1535-52.10.1016/0001-6160(84)90100-7 ↗
16. A. Dhooge and J. Vekeman: Weld. World, 2005, vol. 49, nos. 9/10, pp. 75-93.10.1007/BF03266492 ↗
17. P. Nevasmaa and J. Salonen: Weld. World, 2008, vol. 52, nos. 3/4, pp. 68-78.10.1007/BF03266633 ↗
18. A.G. Vinckier and A.W. Pense: Weld. Res. Counc. Bull., 1974, no. 197, pp. 1–35.
19. W. Lin: Weld. World, 1992, vol. 30, nos. 9/10, pp. 236-42.
20. N.N. Rykalin: Berechnung der Wärmevorgänge beim Schweissen, VEB Verlag Technik, Berlin, Germany, 1953.
21. Ø. Grong: Metallurgical Modelling of Welding, 2nd ed., The Institute of Materials, Cambridge, UK, 1997, pp. 26-45.
22. L.E. Samuels: Light Microscopy of Carbon Steels, ASM International, Materials Park, OH, 1999, pp. 454.10.31399/asm.tb.lmcs.9781627082914 ↗
23. ASTM Designation E 384-08, Standard Test Method for Microindentation Hardness of Materials, 2008.
24. W. Lin, J.C. Lippold, and W.A. Baeslack: Weld. J., 1993, vol. 72, no. 4, pp. 135s-153s.
25. M.J. Cieslak, J.J. Stephens, and M.J. Carr: Metall. Trans. A, 1988, vol. 19A, pp. 657-67.10.1007/BF02649280 ↗
26. T.J. Kelly: Trends Weld. Res., Proc. Int. Conf., 2nd, ASM International, Materials Park, OH, 1990, pp. 151–57.
27. J.C. Lippold, T.W. Nelson, and W. Lin: Annu. North Am. Weld. Res. Conf., Proc., 8th, Columbus, OH, 1992.
28. W. Lin, T.W. Nelson, J.C. Lippold, and W.A. Baeslack: Trends Weld. Res., Proc. Int. Conf., 3rd, ASM International, Materials Park, OH, 1993, pp. 695–702.
29. C.V. Robino, J.R. Michael, and M.J. Cieslak: Sci. Technol. Weld. Joining, 1997, vol. 2, no. 5, pp. 220-30.10.1179/stw.1997.2.5.220 ↗
30. Q. Lu: Ph.D. Dissertation, The Ohio State University, Columbus, OH, 1999.
31. M. Qian and J.C. Lippold: Weld. J., 2002, vol. 81, no. 11, pp. 233s-238s.
32. M. Qian and J.C. Lippold: Weld. J., 2003, vol. 82, no. 6, pp. 145s-150s.
33. K. Hansson, M. Droujevski, and H. Fredriksson: Scand. J. Metall., 2002, vol. 31, no. 4, pp. 256-67.10.1034/j.1600-0692.2002.10562.x ↗
34. J.C. Lippold, W.A. Baeslack III, and I. Varol: Weld. J., 1992, vol. 71, no. 1, pp. 1s-14s.
35. J.C. Lippold and D.J. Kotecki: Welding Metallurgy and Weldability of Stainless Steels, Wiley, Inc., Hoboken, NJ, 2005, pp. 175-77.
36. S.J. Matthews and W.F. Savage: Weld. J., 1971, vol. 50, no. 4, pp. 174s-182s.
37. R.G. Thompson, J.J. Cassimus, D.E. Mayo, and J.R. Dobbs: Weld. J., 1985, vol. 65, no. 4, pp. 91s-96s.
38. G. Eldis: Hardenability Concepts with Applications to Steel, AIME, New York, NY, 1978, pp. 126-57.