journal article·2020-10

Microstructural Evolution in an Fe-10Ni-0.1C Steel During Heat Treatment and High Strain-Rate Deformation

I. Harding, I. Mouton, B. Gault, K. S. Kumar

Publisher page

Abstract

The fine structure in an Fe-10Ni-1.0Mo-0.6Mn-0.6Cr-0.08V-0.1C (wt pct) steel in a multi-step heat-treated condition called ‘QLT’ is understood by tracking its evolution in each step using transmission electron microscopy (TEM) and atom probe tomography; further, the consequence of high strain-rate deformation on the site-specific change in the QLT microstructure is examined by microdiffraction and energy dispersive spectroscopy in the TEM. The QLT treatment results in two generations of austenite (arising from the L- and the T-step) with differing Ni content. The primary focus of this study is on the thermal and mechanical stability of the precipitated austenite and the influence of austenite chemistry and size on the stability. Kolsky bar compression experiments were conducted to isolate a situation where an adiabatic shear band propagated partway through the specimen. Examination of the microstructure in such a specimen showed both generations of austenite to be present far from the shear band, ahead of the shear band and adjacent to the shear band. The austenite immediately ahead of the shear band was fragmented. Within the shear band, evidence was found for deformation-induced transformation to martensite. These findings are discussed within the context of improved damage tolerance and ballistic resistance observed earlier in field tests.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Advanced Materials Characterization Techniques · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. O. Grässel, L. Krüger, G. Frommeyer, and L.W. Meyer: International Journal of Plasticity, 2000, vol. 16, pp. 1391–1409.10.1016/S0749-6419(00)00015-2 ↗
2. G. Frommeyer, U. Brüx, and P. Neumann: ISIJ International, 2003, vol. 43, pp. 438–46.10.2355/isijinternational.43.438 ↗
3. J. Speer, D.K. Matlock, B.C. De Cooman, and J.G. Schroth: Acta Materialia, 2003, vol. 51, pp. 2611–22.10.1016/S1359-6454(03)00059-4 ↗
4. J.G. Speer, D.V. Edmonds, F.C. Rizzo, and D.K. Matlock: Current Opinion in Solid State and Materials Science, 2004, vol. 8, pp. 219–37.10.1016/j.cossms.2004.09.003 ↗
5. A.J. Clarke, J.G. Speer, M.K. Miller, R.E. Hackenberg, D.V. Edmonds, D.K. Matlock, F.C. Rizzo, K.D. Clarke, and E. De Moor: Acta Materialia, 2008, vol. 56, pp. 16–22.10.1016/j.actamat.2007.08.051 ↗
6. O. Dmitrieva, D. Ponge, G. Inden, J. Millán, P. Choi, J. Sietsma, and D. Raabe: Acta Materialia, 2011, vol. 59, pp. 364–74.10.1016/j.actamat.2010.09.042 ↗
7. L. Yuan, D. Ponge, J. Wittig, P. Choi, J.A. Jiménez, and D. Raabe: Acta Materialia, 2012, vol. 60, pp. 2790–804.10.1016/j.actamat.2012.01.045 ↗
8. M. Gouné, F. Danoix, S. Allain, and O. Bouaziz: Scripta Materialia, 2013, vol. 68, pp. 1004–7.10.1016/j.scriptamat.2013.02.058 ↗
9. H. Springer, M. Belde, and D. Raabe: Materials Science and Engineering: A, 2013, vol. 582, pp. 235–44.10.1016/j.msea.2013.06.036 ↗
10. Y. Toji, H. Matsuda, M. Herbig, P.-P. Choi, and D. Raabe: Acta Materialia, 2014, vol. 65, pp. 215–28.10.1016/j.actamat.2013.10.064 ↗
11. M.-M. Wang, C.C. Tasan, D. Ponge, A. Kostka, and D. Raabe: Acta Materialia, 2014, vol. 79, pp. 268–81.10.1016/j.actamat.2014.07.020 ↗
12. Z.J. Xie, S.F. Yuan, W.H. Zhou, J.R. Yang, H. Guo, and C.J. Shang: Materials & Design, 2014, vol. 59, pp. 193–8.10.1016/j.matdes.2014.02.035 ↗
13. M. Belde, H. Springer, G. Inden, and D. Raabe: Acta Materialia, 2015, vol. 86, pp. 1–14.10.1016/j.actamat.2014.11.025 ↗
14. Y. Toji, G. Miyamoto, and D. Raabe: Acta Materialia, 2015, vol. 86, pp. 137–47.10.1016/j.actamat.2014.11.049 ↗
15. E.J. Seo, L. Cho, and B.C. De Cooman: Acta Materialia, 2016, vol. 107, pp. 354–65.10.1016/j.actamat.2016.01.059 ↗
16. M.-M. Wang, C.C. Tasan, D. Ponge, and D. Raabe: Acta Materialia, 2016, vol. 111, pp. 262–72.10.1016/j.actamat.2016.03.070 ↗
17. I.R. Souza Filho, A. Kwiatkowski da Silva, M.J.R. Sandim, D. Ponge, B. Gault, H.R.Z. Sandim, and D. Raabe: Acta Mater., 2019, vol. 166, pp. 178–91.10.1016/j.actamat.2018.12.046 ↗
18. B. Fultz, J.I. Kim, Y.H. Kim, H.J. Kim, G.O. Fior, and J.W. Morris: Metallurgical Transactions A, 1985, vol. 16, pp. 2237–49.10.1007/BF02670423 ↗
19. S. Jin, J.W. Morris, and V.F. Zackay: Metallurgical Transactions A, 1975, vol. 6, pp. 141–9.10.1007/BF02673682 ↗
20. S. Jin, S.K. Hwang, and J.W. Morris: Metallurgical Transactions A, 1975, vol. 6, pp. 1569–75.10.1007/BF02641969 ↗
21. S. Jin, S.K. Hwang, and J.W. Morris: Metallurgical Transactions A, 1975, vol. 6, pp. 1721–6.10.1007/BF02642299 ↗
22. S.-K. Hwang, S. Jin, and J.W. Morris: Metallurgical Transactions A, 1975, vol. 6, pp. 2015–21.10.1007/BF03161826 ↗
23. C.K. Syn, S. Jin, and J.W. Morris: Met. Trans. A, 1976, vol. 7A, pp. 1827–32.10.1007/BF02659812 ↗
24. C.K. Syn, B. Fultz, and J.W. Morris: Metallurgical Transactions A, 1978, vol. 9, pp. 1635–40.10.1007/BF02661946 ↗
25. K.J. Kim and L.H. Schwartz: Materials Science and Engineering, 1978, vol. 33, pp. 5–20.10.1016/0025-5416(78)90149-0 ↗
26. J.I. Kim and J.W. Morris: Metallurgical Transactions A, 1980, vol. 11, pp. 1401–6.10.1007/BF02653495 ↗
27. J.R. Strife and D.E. Passoja: Metallurgical Transactions A, 1980, vol. 11, pp. 1341–50.10.1007/BF02653488 ↗
28. J.I. Kim and J.W. Morris: Metallurgical Transactions A, 1981, vol. 12, pp. 1957–63.10.1007/BF02643809 ↗
29. J.I. Kim, C.K. Syn, and J.W. Morris: Metallurgical Transactions A, 1983, vol. 14, pp. 93–103.10.1007/BF02643742 ↗
30. J.I. Kim, H.J. Kim, and J.W. Morris: Metallurgical Transactions A, 1984, vol. 15, pp. 2213–9.10.1007/BF02647104 ↗
31. B. Fultz and J.W. Morris: Metall. Trans. A, 1985, pp. 173–7.10.1007/BF02816043 ↗
32. B. Fultz and J.W. Morris: Metallurgical Transactions A, 1985, vol. 16, pp. 2251–6.10.1007/BF02670424 ↗
33. B. Fultz, J.I. Kim, Y.H. Kim, and J.W. Morris: Metallurgical Transactions A, 1986, vol. 17, pp. 967–72.10.1007/BF02661262 ↗
34. C. Hayzelden and B. Cantor: Acta Metallurgica, 1986, vol. 34, pp. 233–42.10.1016/0001-6160(86)90194-X ↗
35. C.W. Marschall, R.F. Hehemann, and A.R. Troiano: Transactions of American Society of Metals, 1962, vol. 55, pp. 135–48.
36. P. Wang and K.S. Kumar: Materials Science and Engineering: A, 2009, vol. 519, pp. 184–97.10.1016/j.msea.2009.04.063 ↗
37. X.J. Zhang: Materials Science and Technology, 2012, vol. 28, pp. 818–22.10.1179/1743284712Y.0000000015 ↗
38. D. Isheim, A.H. Hunter, X.J. Zhang, and D.N. Seidman: Metallurgical and Materials Transactions A, 2013, vol. 44, pp. 3046–59.10.1007/s11661-013-1670-6 ↗
39. R.W. Fonda and G. Spanos: Metallurgical and Materials Transactions A, 2014, vol. 45, pp. 5982–9.10.1007/s11661-014-2588-3 ↗
40. D. Jain, D. Isheim, X.J. Zhang, G. Ghosh, and D.N. Seidman: Metallurgical and Materials Transactions A, 2017, vol. 48, pp. 3642–54.10.1007/s11661-017-4146-2 ↗
41. D. Jain, D.N. Seidman, E.J. Barrick, and J.N. DuPont: Metallurgical and Materials Transactions A, 2018, vol. 49, pp. 1031–43.10.1007/s11661-018-4470-1 ↗
42. E.J. Barrick and J.N. DuPont: Materials Science and Engineering: A, 2019, vol. 748, pp. 189–204.10.1016/j.msea.2019.01.085 ↗
43. I. Harding, I. Mouton, B. Gault, D. Raabe, and K.S. Kumar: Scripta Materialia, 2019, vol. 172, pp. 38–42.10.1016/j.scriptamat.2019.06.036 ↗
44. P.K. Lambert: Johns Hopkins University, 2017.
45. F. Yuan, X. Bian, P. Jiang, M. Yang, and X. Wu: Mechanics of Materials, 2015, vol. 89, pp. 47–58.10.1016/j.mechmat.2015.06.004 ↗
46. K. Thompson, D. Lawrence, D.J. Larson, J.D. Olson, T.F. Kelly, and B. Gorman: Ultramicroscopy, 2007, vol. 107, pp. 131–9.10.1016/j.ultramic.2006.06.008 ↗
47. B. Gault, A.J. Breen, Y. Chang, J. He, E.A. Jägle, P. Kontis, P. Kürnsteiner, A. Kwiatkowski da Silva, S.K. Makineni, I. Mouton, Z. Peng, D. Ponge, T. Schwarz, L.T. Stephenson, A. Szczepaniak, H. Zhao, and D. Raabe: Journal of Materials Research, 2018, vol. 33, pp. 4018–30.10.1557/jmr.2018.375 ↗
48. H. Zhao, F. De Geuser, A. Kwiatkowski da Silva, A. Szczepaniak, B. Gault, D. Ponge, and D. Raabe: Acta Materialia, 2018, vol. 156, pp. 318–29.10.1016/j.actamat.2018.07.003 ↗
49. K.T. Ramesh: in Springer Handbook of Experimental Solid Mechanics, Springer, New York, 2008, pp. 929–60.10.1007/978-0-387-30877-7_33 ↗
50. S. Takaki, K. Fukunaga, J. Syarif, and T. Tsuchiyama: Materials Transactions, 2004, vol. 45, pp. 2245–51.10.2320/matertrans.45.2245 ↗
51. S.E. Rigby, A.D. Barr, and M. Clayton: Proceedings of the Institution of Civil Engineers - Engineering and Computational Mechanics, 2018, vol. 171, pp. 3–13.
52. D.J. Parry, A.G. Walker, and P.R. Dixon: Meas. Sci. Technol., 1995, vol. 6, pp. 443–6.10.1088/0957-0233/6/5/001 ↗
53. H. Huang, O. Matsumura, and T. Furukawa: Materials Science and Technology, 1994, vol. 10, pp. 621–6.10.1179/mst.1994.10.7.621 ↗
54. Y. Inokuti and B. Cantor: Acta Metallurgica, 1982, vol. 30, pp. 343–56.10.1016/0001-6160(82)90214-0 ↗
55. S.M.C. van Bohemen and J. Sietsma: Materials Science and Technology, 2014, vol. 30, pp. 1024–33.10.1179/1743284714Y.0000000532 ↗
56. H. Wang, X. Sun, P. Yang, W. Mao, and L. Meng: Journal of Materials Science & Technology, 2015, vol. 31, pp. 191–8.10.1016/j.jmst.2014.03.027 ↗
57. S.M. Walley: Metallurgical and Materials Transactions A, 2007, vol. 38, pp. 2629–54.10.1007/s11661-007-9271-x ↗
58. P.R. Guduru, A.J. Rosakis, and G. Ravichandran: Mechanics of Materials, 2001, vol. 33, pp. 371–402.10.1016/S0167-6636(01)00051-5 ↗
59. M.A. Meyers, Y.B. Xu, Q. Xue, M.T. Pérez-Prado, and T.R. McNelley: Acta Materialia, 2003, vol. 51, pp. 1307–25.10.1016/S1359-6454(02)00526-8 ↗