journal article·2017-11Open access

The Effect of Sr Modifier Additions on Double Oxide Film Defects in 2L99 Alloy Castings

Qi Chen, W. D. Griffiths

Abstract

Abstract In this paper, Sr modifier (300 ppm) was added to 2L99 alloy sand castings to investigate its effect on bifilm defects in the castings. Two different sand molds were used in this study, with good and bad running system designs, to introduce different amounts of bifilm defects into the castings. The mechanical properties of the modified 2L99 castings were compared to the properties of unmodified castings and showed that with high bifilm defect contents (H) the Sr addition reduced the Weibull modulus of the UTS by 67 pct and the Position Parameter by 5 pct, and introduced a bimodal distribution into the Weibull plot of the pct Elongation. However, for castings with low bifilm defect content (L), the Weibull moduli of both the UTS and pct Elongation were significantly improved (by 78 and 73 pct, respectively) with the addition of Sr. The Position Parameter of the pct Elongation was improved by 135 pct. The results suggested that a desirable modification effect can only be achieved while the bifilm defect content in a casting was low.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. D. Emadi, J.E. Gruzleski, and J.M. Toguri: Metall. Trans. B, 1993. Vol. 24(6), pp. 1055-1063.10.1007/BF02660997 ↗
2. J.E. Gruzleski and B.M. Closset: AFS. Trans., 1990, 92, p. 256.
3. S.C. Flood and J.D. Hunt: Metal Sci., 1981. Vol. 15(7), pp. 287-294.10.1179/030634581790426813 ↗
4. A. Knuutinen, K. Nogita, S.D. McDonald and A.K. Dahle: Light Metals, 2001. Vol. 1(4), pp. 229-240.10.1016/S1471-5317(02)00004-4 ↗
5. K. Nogita, S. D. McDonald, and A.K. Dahle: Mater. Trans. 2004, Vol. 45(2), pp. 323-326.10.2320/matertrans.45.323 ↗
6. G. Sigworth: AFS Trans, 1983, Vol. 66, pp. 7-16.
7. S.D. McDonald, K. Nogita, and A.K. Dahle: Acta Mater. 2004, Vol. 52(14), pp. 4273-4280.10.1016/j.actamat.2004.05.043 ↗
8. N.S. Tiedje, J.A. Tayor and M.A. Easton: Metall. Trans. A, 2012, Vol. 43(12), pp. 4846-4858.10.1007/s11661-012-1308-0 ↗
9. S.Z. Lu and A. Hellawell: Metall. Trans. A, 1987, Vol. 18(10), pp. 1721-1733.10.1007/BF02646204 ↗
10. D.R. Hamilton and R.G. Seidensticker: J. Appl. Phys., 1960, Vol. 31, pp.1165-1173.10.1063/1.1735796 ↗
11. J. Li, F. Hage, M. Wiessner, L. Romaner, D. Scheiber, B. Sartory, Q. Ramasse and P. Schumacher: Sci. Rep., 2015, Vol. 5, 13802.10.1038/srep13802 ↗
12. M. Timpel, N. Wanderka, R. Schlesiger, T. Yamamoto, N. Lazarev, D. Isheim, G. Schmitz, S. Matsumura and J. Banhart: Acta Mater. 2012, Vol. 60, pp. 3920-3928.10.1016/j.actamat.2012.03.031 ↗
13. H. Eiken and M. Apel: IOP Conf. Ser. Mater. Sci. Eng., Vol. 84(1): 12084 (2016).
14. J. Campbell: Complete Casting Handbook, Butterworth-Heinemann, Oxford, 2011, pp. 19-28.10.1016/B978-1-85617-809-9.10002-7 ↗
15. W. Weibull: J. Appl. Mech. Tran. ASME, 1951, Vol. 18(3), pp. 293-297.10.1115/1.4010337 ↗
16. N.R. Green and J. Campbell: J. Mater. Sci. Eng. A, 1993, Vol. 173(1), pp. 261-266.10.1016/0921-5093(93)90226-5 ↗
17. M. Tiryakioğlu and D. Hudak: J. Mater. Sci., 2008, Vol. 527(1-2), pp. 397-399.
18. C. Nyahumwa, N. R. Green and J. Campbell: AFS Trans. 1998, Vol. 106, pp. 215-223.
19. H. Iwahori, K. Yonekura, Y. Yamamoto and M. Nakamura: J. Jpn. Foundrym. Soc., 1989, Vol. 61(10), pp. 730-735.
20. D. Emadi, J. Gruzleski, and M. Pekguleryuz: AFS Trans., 1996, Vol. 104, pp. 763-768.
21. S. Jacob: Fonderie, 1977, Vol. 363, pp. 13-25.
22. J. Campbell and M. Tiryakioglu: J. Mater. Sci. Technol., 2010, Vol. 26(3), pp. 262-268.10.1179/174328409X425227 ↗
23. R. Raiszadeh and W.D. Griffiths: Metall. Trans. B, 2006, Vol. 37(6), pp. 865-871.10.1007/BF02735007 ↗
24. M. Nateghian, R. Raiszadeh, and H. Doostmohammadi: Metall. Trans. B, 2012, Vol. 43(6), pp. 1540-1549.10.1007/s11663-012-9708-5 ↗
25. B. Farhoodi, R. Raiszadeh, and M. H. Ghanaatian: J. Mater. Sci. Technol., 2014, Vol. 30(2), pp. 154-162.10.1016/j.jmst.2013.09.001 ↗
26. S.M. Miresmaeili, J. Campbell, S. G. Shabestari and S. M. A. Boutorabi: Metall. Trans. A, 2005, Vol. 36(9), pp. 2341-2349.10.1007/s11661-005-0106-3 ↗
27. A. Khalili and K. Kromp: J. Mater. Sci., 1991, Vol. 26(24), pp. 6741-6752.10.1007/BF02402669 ↗
28. M. Tiryakioğlu and J. Campbell: Metall. Trans. A, 2010, Vol. 41(12), pp.3121-3129.10.1007/s11661-010-0364-6 ↗
29. D. Hudak and M. Tiryakioğlu: Mater. Sci. Eng. A, 2011, Vol. 528(27), pp. 8028-8030.10.1016/j.msea.2011.07.013 ↗
30. G.K. Sigworth, Int. J. Metalcast., 2008, Vol. 2(2), pp. 19-40.10.1007/BF03355425 ↗
31. M.A. El-Sayed, A.G. Salem, A.Y. Kandeil and W.D. Griffiths, Metall. Trans. B, 2014, Vol. 45(4), pp. 1398-1406.10.1007/s11663-014-0035-x ↗