Investigation of Oxide Bifilms in Investment Cast Superalloy IN100: Part II. Characterization
Source abstract
Abstract
Oxide bifilms are a proposed casting inclusion reported to have been observed in vacuum investment cast polycrystalline Ni-based superalloys. Ongoing research seeks to determine if current superalloy casting practices can result in the formation of oxide bifilms, and subsequently if it is possible to observe and characterize this phenomenon. The effect of casting atmosphere, turbulence, filtering, hot isostatic pressing, and heat treatment has been investigated to identify the critical parameters that have been reported to result in bifilm formation in Ni-based superalloy IN100. Scanning Auger microscopy (SAM), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HR-TEM) were utilized to characterize samples from each casting condition. In situ ultrahigh vacuum Auger fractography did not indicate the presence of bifilms on the fracture behavior of IN100 in any processing condition. SAM analysis identified a sulfur-enriched monolayer on the surface of dendritic casting porosity, and identified heterogeneous Ti oxycarbide inclusions in air cast IN100. SEM analysis also indicated the presence of Ti oxycarbide inclusions in air cast IN100, and determined that these inclusion structures consist of fine blocky external M(Ti, Mo)C carbide enveloping an internal core of alumina. HR-TEM analysis indicated that none of the oxycarbide inclusion interfaces exist as discontinuous unbound interfaces, and that the internal alumina core is an ultra-fine polycrystalline structure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgical Processes and Thermodynamics · High Temperature Alloys and Creep · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. [1] J. Campbell and M. Tiryakioglu: Metall. Trans. B, 2012, vol. 43, pp. 902-914.10.1007/s11663-012-9655-1 ↗
2. [2] A. Rashid and J. Campbell: Metall. Trans. A, 2004, vol. 35A, pp. 2063-2071.10.1007/s11661-004-0155-z ↗
3. [3] J. Staley, M. Tiryakioglu, and J. Campbell: Mater. Sci. Eng. A, 2007, vol. 465, pp. 136-145.10.1016/j.msea.2007.02.009 ↗
4. [4] J. Staley, M. Tiryakioglu, and J. Campbell: Mater. Sci. Eng. A, 2007, vol. 460, pp. 324-334.10.1016/j.msea.2007.01.049 ↗
5. [5] J. Campbell: Mater. Sci. Tech., 2006, vol. 22, pp. 127-145.10.1179/174328406X74248 ↗
6. [6] M. Tiryakioglu, J. Staley, and J. Campbell: Mater. Sci. Eng. A, 2008, vol. 487, pp. 383-387.10.1016/j.msea.2007.11.005 ↗
7. [7] Q. Wang, C. Davidson, J. Griffiths, and P. Crepeau: Metall. Trans. B, 2006, vol. 37, pp. 887-895.10.1007/BF02735010 ↗
8. [8] M. Felberbaum and M. Rappaz: Acta Mater., 2011, vol. 59, pp. 6849-6860.10.1016/j.actamat.2011.07.005 ↗
9. [9] J. Campbell: Mater. Sci. Tech., 2008, vol. 24, pp. 875-879.10.1179/174328408X307139 ↗
10. [10] J. Campbell: Int. J. Metalcast., 2012, vol. 6, pp. 7-18.10.1007/BF03355529 ↗
11. [11] J. Knott, P. Beeley, J. Griffiths, N. Green, C. Newton, and J. Campbell: Mater. Sci. Tech., 2006, vol. 22, pp. 999-1008.10.1179/174328406X109221 ↗
12. [12] D. Dispinar and J. Campbell: J. Mat. Process. Tech., 2006, vol. 182, pp. 405-410.10.1016/j.jmatprotec.2006.08.021 ↗
13. [13] S. Fox and J. Campbell: Scripta Mater., 2000, vol. 43, pp. 881-886.10.1016/S1359-6462(00)00506-6 ↗
14. [14] D. Li, J. Campbell, and Y. Li: J. Mater. Process. Tech., 2004, vol. 148, pp. 310-316.10.1016/j.jmatprotec.2004.02.032 ↗
15. 16.E. Lambers, C. Dykstal, J. Seo, J. Rowe, P. Holloway (1996) Oxid. Metall., 45: 301-2110.1007/BF01046987 ↗
16. [17] P. Holloway and R. Outlaw: Surf. Sci., 1981, vol. 111, pp. 300-316.10.1016/0039-6028(80)90710-4 ↗
17. 18. R. Hertzberg: Deformation and Fracture Mechanics of Engineering Materials. Wiley, New York, 1996
18. [19] Commonwealth Scientific Corp: Ion Beam Etch Rates and Sputter Yields, Bulletin #293-93, Alexandria, VA, 1994.
19. 20.W. Freeman Jr (1984) jgdjgjkdjgj dngkl. In: C. Sims, N. Stoloff, W. Hagel (eds) Superalloys II: High-Temperature Materials for Aerospace and Industrial Power, pp. 411-439. Wiley, New York
20. 21.J. Campbell: Castings: The New Metallurgy of Cast Metals. Butterworth Heinemann, Burlington, 2003.10.1016/B978-075064790-8/50019-X ↗
21. [22] D. Dispinar and J. Campbell: Mater. Sci. Eng. A, 2011, vol. 528, pp. 3860-3865.10.1016/j.msea.2011.01.084 ↗
22. [23] X. Dai, X. Yang, J. Campbell, and J. Wood: Mater. Sci. Eng. A, 2003, vol. 354, pp. 315-325.10.1016/S0921-5093(03)00021-2 ↗
23. [24] L. Harris: J. Appl. Phys., 1968, vol. 39, pp. 1428-1431.10.1063/1.1656375 ↗
24. [25] J. Chen, J. Lee, C. Jo, S. Choe, and Y. Lee: Mater. Sci. Eng. A, 1998, vol. 247, pp. 113-125.10.1016/S0921-5093(97)00761-2 ↗
25. [26] P. Quested and M. McLean: Mater. Sci. Eng., 1984, vol. 65, pp. 171-180.10.1016/0025-5416(84)90210-6 ↗
26. S. Cockcroft, A. Mitchell, D. Tripp, A. Schmalz, and T. Degawa: Proceedings of Superalloys 1992, S. Antolovich, R. Stusrud, R. MacKay, D. Anton, T. Khan, R. Kissinger, and D. Klarstrom eds., TMS, Seven Springs, 1992, pp. 577–86.10.7449/1992/Superalloys_1992_577_586 ↗
27. [28] R. Fernandez, J. Lecomte, and T. Kattamis: Metall. Trans. A, 1978, vol. 9A, pp. 1381-1386.10.1007/BF02661809 ↗
28. F. Beneduce, A. Mitchell, S. Cockcroft, and A. Schmalz: Proceedings of Superalloys 1996, R. Kissinger, D. Deye, D. Anton, A. Cetel, M. Nathal, T. Pollock, and D. Woodford, eds., TMS, Seven Springs, 1996, pp. 465–69.10.7449/1996/Superalloys_1996_465_469 ↗
29. 30.G. Bouse, J. Mihalisin (1989) ndlkjfk jksbf. In: J. Tien, T. Caulfield eds., Superalloys, Supercomposites, and Superceramics, pp. 99-147. Academic Press, Boston10.1016/B978-0-12-690845-9.50010-5 ↗