journal article·2013-06

Precipitate Size in the Superalloy IN738LC During Compression Creep

Arun Altincekic, Ercan Balikci

Publisher page

Abstract

Superalloys are high-temperature materials that are used widely in many industries especially in several engine components in gas turbines. One of the many nickel-base superalloys is IN738LC, which possesses a good high-temperature strength and hot corrosion resistance. It is employed mainly in nozzle guide vanes and blades of land-based turbines. The strengthening is provided mainly by coherent γ′ precipitates. The current research is undertaken to determine precipitate size in IN738LC specimens aged under compressive stress. To observe the influence of magnitude of stress, a constant compressive load is applied to conical specimens that are aged in an inert atmosphere for various times [24, 192, 480, and 960 hours at 1223 K (950 °C) and 12, 24, 192, and 480 hours at 1323 K (1050 °C)]. Thus, the study of microstructural changes due to various stress levels becomes possible with a single specimen in the same experimental condition. A single-size distribution of precipitates has been observed except for the 192-hour and 480-hour experiments at 1323 K (1050 °C). The results indicate that the average precipitate size is directly proportional to the temperature but inversely proportional to the applied stress, although in some specimens, maximum size is observed at medium-stress levels. Strain becomes effective at most severely crept specimen by causing a merging of precipitates. Raft degeneration is also observed in this specimen. The growth exponent is found to vary with stress and temperature between 2.97 and 3.78.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · Additive Manufacturing Materials and Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. M. Durand-Charre: The Microstructure of Superalloys, Gordon and Breach Science Publishers, Amsterdam, The Netherlands, 1997.
2. R.C. Reed: The Superalloys-Fundamentals and Applications, Cambridge University Press, New York, NY, 2006.10.1017/CBO9780511541285 ↗
3. C.T. Sims, N.S. Stoloff, and W.C. Hagel, Eds.: Superalloys II–High- Temperature Materials for Aerospace and Industrial Power, Wiley, New York, NY, 1987.
4. The Nickel Producers Environmental Research Association (NIPERA): Alloy IN-738 Technical Data, http://www.nipera.org/~/Media/Files/TechnicalLiterature/IN_738Alloy_PreliminaryData_497_.pdf, July 2012.
5. E. Balikci: Ph.D. Dissertation, Louisiana State University, Baton Rouge, LA, 1998.
6. C.G. Bieber and J.J. Galka: U.S. Patent No. 3,459,545, Aug. 5, 1969.
7. D.A. Porter and K.E. Easterling: Phase Transformations in Metals and Alloys, 2nd ed., Chapman & Hall, New York, NY, 1992.10.1007/978-1-4899-3051-4 ↗
8. I.M. Lifshitz and V.V. Sloyozov, J. Phys. Chem. Solids, 1961, vol. 19 (1–2), pp. 35–50.10.1016/0022-3697(61)90054-3 ↗
9. C. Wagner: Z. Elektrochemie, 1961, vol. 65 (7–8), pp. 581–91.
10. L. Ratke and P.W. Voorhees: Growth and Coarsening: Ostwald Ripening in Material Processing, Springer-Verlag, Berlin, Germany, 2002.10.1007/978-3-662-04884-9 ↗
11. M. Doi: Mater. Trans., 1992, vol. 33 (7), pp. 637–49.10.2320/matertrans1989.33.637 ↗
12. A.J. Ardell: Acta Metall., 1972, vol. 20 (1), pp. 61–71.10.1016/0001-6160(72)90114-9 ↗
13. A.D. Brailsford and P. Wynblatt: Acta Metall., 1979, vol. 27 (3), pp. 489–97.10.1016/0001-6160(79)90041-5 ↗
14. C.K.L. Davies, P. Nash, and R.N. Stevens. Acta Metall., 1980, vol. 28 (2), pp. 179–89.10.1016/0001-6160(80)90067-X ↗
15. S.V. Prikhodko and A.J. Ardell: Acta Mater., 2003, vol. 51 (17), pp. 5001–12.10.1016/S1359-6454(03)00329-X ↗
16. A. Ges, O. Fornaro, and H. Palacio: J. Mater. Sci., 1997, vol. 32 (14), pp. 3687–91.10.1023/A:1018694716756 ↗
17. P.K. Footner and B.P. Richards: J. Mater. Sci., 1982, vol. 17 (7), pp. 2141–53.10.1007/BF00540433 ↗
18. H. Furukawa: Adv. Phys., 1985, vol. 34 (6), pp. 703–50.10.1080/00018738500101841 ↗
19. A.J. Ardell and V. Ozolins: Nat. Mater., 2005, vol. 4, pp. 309–16.10.1038/nmat1340 ↗
20. S.V. Prikhodko and A.J. Ardell: Acta Mater., 2003, vol. 51 (17), pp. 5021–36.10.1016/S1359-6454(03)00328-8 ↗
21. S.V. Prikhodko and A.J. Ardell: Acta Mater., 2003, vol. 51 (17), pp. 5013–19.10.1016/S1359-6454(03)00327-6 ↗
22. N.V. Starostina, S.V. Prikhodko, A.J. Ardell, and S. Prasad: Mater. Sci. Eng. A, 2005, vol. 397 (1–2), pp. 264–70.10.1016/j.msea.2005.02.050 ↗
23. J. Li and R.P. Wahi: Acta Metall. Mater., 1995, vol. 43 (2), pp. 507–17.10.1016/0956-7151(94)00252-D ↗
24. J.W. Cahn: Trans. Metall. Soc. AIME, 1968, vol. 242, pp. 166–80.
25. J.X. Yang, Q. Zheng, X.F. Sun, H.R. Guan, and Z.Q. Hu: Mater. Sci. Eng. A, 2007, vol. 457, pp. 148–55.10.1016/j.msea.2006.12.041 ↗
26. T. Link, A. Epishin, and B. Fedelich: Philos. Mag., 2009, vol. 89 (13), pp. 1141–59.10.1080/14786430902877810 ↗
27. F.Z. Sierra, D. Narzary, C. Bolaina, J.C. Han, J. Kubiak, and J. Nebradti: Heat Transfer and Thermal Mechanical Stress Distributions in Gas Turbine Blades, Presented at ASME Turbo Expo 2009: Power for Land, Sea, and Air, Orlando, FL, June 8–12, 2009.10.1115/GT2009-59194 ↗
28. N. Miura, K. Nakata, M. Miyazaki, Y. Hayashi, and Y. Kondo: Mater. Sci. Forum, 2010, vols. 638–642, pp. 2291–96.10.4028/www.scientific.net/MSF.638-642.2291 ↗
29. A.K. Dwarapureddy, E. Balikci, S. Ibekwe, and A. Raman: J. Mater. Sci., 2008, vol. 43 (6), pp. 1802–10.10.1007/s10853-007-2342-y ↗
30. E. Balikci, R.A. Mirshams, and A. Raman: J. Mater. Eng. Perform., 2000, vol. 9 (3), pp. 324–29.10.1361/105994900770345999 ↗
31. E. Balikci and D. Erdeniz: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1391–98.10.1007/s11661-010-0241-3 ↗
32. E. Balikci, R.A. Mirshams, and A. Raman: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1993–2003.10.1007/s11661-997-0156-9 ↗
33. E. Balikci, R.A. Mirshams, and A. Raman: Z. Metallkd., 1999, vol. 90 (2), pp. 132–40.
34. E. Balikci and A. Raman: J. Mater. Sci., 2000, vol. 35 (14), pp. 3593–97.10.1023/A:1004869714854 ↗
35. E. Balikci and A. Raman: J. Mater. Sci., 2008, vol. 43 (3), pp. 927–32.10.1007/s10853-007-2206-5 ↗
36. I. Roy, E. Balikci, S. Ibekwe, and A. Raman: J. Mater. Sci., 2005, vol. 40 (23), pp. 6207–15.10.1007/s10853-005-3154-6 ↗
37. E. Balikci, R.E. Ferrell, Jr., and A. Raman: Z. Metallkd., 1999, vol. 90 (2), pp. 141–46.
38. R. Rosenthal and D.R.F. West: Mater. Sci. Technol., 1999, vol. 15, no. 12, pp. 1387–94.10.1179/026708399101505518 ↗
39. N. El-Bagoury, M. Waly, and A. Nofal: Mater. Sci. Eng. A, 2007, vol. 487, nos. 1–2, pp. 152–61.
40. R.S. Moshtaghin and S. Asgari: Mater. Des., 2003, vol. 24 (5), pp. 325–30.10.1016/S0261-3069(03)00061-X ↗
41. S. Behrouzghaemi and R.J. Mitchell: Mater. Sci. Eng. A, 2007, vol. 498 (1–2), pp. 266–71.
42. M. Ignat, J.Y. Buffiere, and J.M. Chaix: Acta Metall. Mater., 1993, vol. 41 (3), pp. 855–62.10.1016/0956-7151(93)90019-O ↗
43. A. Epishin, T. Link, H. Klingelhöffer, B. Fedelich, U. Brückner, and P.D. Portella: Mater. Sci. Eng. A, 2009, vols. 510–511, pp. 262–65.10.1016/j.msea.2008.04.135 ↗
44. X.W. Li, Y.M. Hu, and Z.G. Wang: Mater. Sci. Eng. A, 1998, vol. 248, pp. 299–303.10.1016/S0921-5093(98)00501-2 ↗
45. C. Buque, J. Bretschneider, A. Schwab, and C. Holste: Mater. Sci. Eng. A, 2001, vol. 300, pp. 254–62.10.1016/S0921-5093(00)01784-6 ↗
46. A. Epishin, T. Link, and G. Nolze: J. Microsc., 2007, vol. 228, pp. 110–17.10.1111/j.1365-2818.2007.01831.x ↗
47. W.S. Rasband: ImageJ, U.S. National Institutes of Health, Bethesda, MD, 1997–2007. http://rsb.info.nih.gov/ij/.
48. A. Altincekic: MSc. Thesis, Bogazici University, Istanbul, Turkey, 2011.
49. D. Mclean: Met. Sci., 1984, vol. 18, pp. 249–56.10.1179/030634584790420113 ↗
50. J. Tiley, G.B. Viswanathan, R. Srinivasan, R. Banerjee, D.M. Dimiduk, and H.L. Fraser: Acta Mater., 2009, vol. 57 (8), pp. 2538–49.10.1016/j.actamat.2009.02.010 ↗
51. A.J. Ardell and V. Ozolins: Nat. Mater., 2005, vol. 4, pp. 309–16.10.1038/nmat1340 ↗
52. A.M. Ges, O. Fornaro, and H.A. Palacio: Mater. Sci. Eng. A, 2007, vol. 458, pp. 96–100.10.1016/j.msea.2006.12.107 ↗
53. J. Safari, S. Nategh, and M. McLean: Mater. Sci. Technol., 2006, vol. 22 (8), pp. 888–98.10.1179/174328406X91168 ↗
54. W.C. Johnson: Metall. Trans. A, 1987, vol. 18A, pp. 233–47.10.1007/BF02825704 ↗
55. P.W. Voorhees and W.C. Johnson: J. Chem. Phys., 1986, vol. 84 (9), pp. 5108–21.10.1063/1.450664 ↗
56. C. Ahn, N. Bennett, S.T. Dunham, and N.E.B. Cowern: Phys. Rev. B, 2009, vol. 79 (7), pp. 073201-1–073201-4.10.1103/PhysRevB.79.073201 ↗
57. F. Li and A.J. Ardell: J. Phase Equilib., 1998, vol. 19 (4), pp. 334–39.10.1361/105497198770342067 ↗
58. R.D. Vengrenovich, Y.V. Gudyma, and S.V. Yarema: Phys. Met. Metallogr., 2001, vol. 91 (3), pp. 228–32.
59. Y.M. Ustguyov: Phys. Met. Metallogr., 2007, vol. 104 (5), pp. 453–60.10.1134/S0031918X07110038 ↗
60. J.X. Zhang, H. Harada, Y. Koizumi, and T. Kobayashi: J. Mater. Sci., 2010, vol. 45 (2), pp. 523–32.10.1007/s10853-009-3970-1 ↗
61. R.W. Hertzberg: Deformation and Fracture Mechanics of Engineering Materials, Wiley, New York, NY, 1996.
62. M. Doi, T. Miyazaki, and T. Wakatsuki: Mater. Sci. Eng., 1984, vol. 67 (2), pp. 247–53.10.1016/0025-5416(84)90056-9 ↗