journal article·2019-07-15

Microstructure Evolution of Fine-Grained Heat-Affected Zone of Gr.92 Steel Welded Joint During Creep

Y. Liu, S. Tsukamoto, H. Hongo, F. Yin, M. Tabuchi, F. Abe

Publisher page

Abstract

The microstructure evolution of fine-grained heat-affected zone (FGHAZ) of Gr.92 steel welded joint has been investigated during creep using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy. The microstructure evolution strongly depended on the applied stress level. At the stress level of 90 MPa, the grains of the FGHAZ were coarsened after creep. When the stress level decreased to 70 MPa, the grains of the FGHAZ were found to be further refined during creep owing to continuous dynamic recrystallization (subgrains rotation). This was verified by the increase in boundary length featuring random misorientation angles after creep. Recrystallized microstructure was only observed for the FGHAZ of welded joints after creep, but not for the Ac3 heat-affected zone (HAZ) simulated samples which exhibited homogeneous microstructure even at the low applied stress of 50 MPa. In high stress regime the creep strength of the welded joints was almost the same as that of Gr.92 steel owing to the mechanical constraint originating from the heterogeneous creep property of welds. In low stress regime, the creep strength of the welded joint was inferior to that of Gr.92 steel and approached that of the Ac3 HAZ simulated sample as the applied stress decreased. This was caused by the relaxation of the constraint owing to grain boundary sliding. Recrystallization was regarded as a sign of relaxation of constraint and deterioration of creep property for high-Cr heat-resistant steel welded joints.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and mechanical properties · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. R. Blum, and R.W. Vanstone: Proc. 6th Inter. Charles Parsons Turbine Conf. Dublin, Ireland, 2003. pp. 489–510.
2. H.K. Bhadeshia, ISIJ Inter., 2001, Vol.41, pp.626-640.10.2355/isijinternational.41.626 ↗
3. D. Rojas, J. Garcia, O. Prat, G.Sauthoff, A.R.Kaysser-Pyzalla, Mater. Sci. Eng. A, 2011, Vol.528, pp.5164-5176.10.1016/j.msea.2011.03.037 ↗
4. K.Sawada, K.Kubo, F.Abe, Mater. Sci. Eng. A, 2001, Vol.319, pp.784-787.10.1016/S0921-5093(01)00973-X ↗
5. F.Abe, Curr. Opin. Solid State Mater. Sci., 2004, Vol.8, pp.305-311.10.1016/j.cossms.2004.12.001 ↗
6. F.Abe, Metall. Mater. Trans. A, 2005, Vol.6, pp.321-332.10.1007/s11661-005-0305-y ↗
7. K. Maruyama, K.Sawada, J. Koike, ISIJ Inter., 2001 Vol. 41, pp.641-653.10.2355/isijinternational.41.641 ↗
8. D.J. Abson, J.S. Rothwell, Inter. Mater. Rev., 2013, Vol. 58, pp. 437-473.10.1179/1743280412Y.0000000016 ↗
9. H. Hirata and K. Ogawa, Welding Inter. 2005, Vol. 19 pp.109-117.10.1533/wint.2005.3377 ↗
10. H. Hongo, M. Tabuchi and T. Watanabe, Metall. Mater. Trans. A, 2012, Vol.43, pp.1163-1173.10.1007/s11661-011-0967-6 ↗
11. Y. Li, H. Hongo, M. Tabuchi, Y. Takahashi and Y. Monma, Inter. J. Pressure Vessels & Piping, 2009, Vol.86 pp.585-59210.1016/j.ijpvp.2009.04.008 ↗
12. F. Abe, M. Tabuchi, S. Tsukamoto and T. Shirane, Inter. J. Pressure Vessels and Piping, 2010, Vol.87, pp.598-604.10.1016/j.ijpvp.2010.08.005 ↗
13. J.A. Francis, W. Muzur and H. K. D. H. Bhadeshia, Mater. Sci. Technol., 2006, Vol. 22, pp. 1387-1395.10.1179/174328406X148778 ↗
14. F. Abe and M. Tabuchi, Sci. Tech. Welding Joining, 2004, Vol. 19, pp.22-29.10.1179/136217104225017107 ↗
15. D. Li, K. Shinozaki, H. Kuroki, H. Harada and K. Ohishi, Sci. Tech. Welding Joining, 2003, Vol. 8, pp.296-302.10.1179/136217103225005453 ↗
16. D. Li, K. Shinozaki, H. Harada and K. Ohishi, Metall. Mater. Trans. A, 2005, Vol. 36, pp.107-115.10.1007/s11661-005-0143-y ↗
17. Y. Liu, S. Tsukamoto, T. Shirane and F. Abe, Metall. Mater. Trans. A, 2013, Vol. 44, pp.4626-4633.10.1007/s11661-013-1801-0 ↗
18. Y. Liu, S.Tsukamoto, K. Sawada and F. Abe, Metall. Mater. Trans. A, 2014, Vol.45, pp.1306-1314.10.1007/s11661-013-2072-5 ↗
19. M.Tabuchi, A. T. Yikobori Jr., R. Sugiura, M.Yatomi, A.Fuji, K.Kobayashi, Eng. Frac. Mech., 2010 Vol.77, pp.3066-3076.10.1016/j.engfracmech.2010.03.044 ↗
20. M. Yaguchi, T. Matsumura, and K. Hoshino: Proc. ASME 2012 Pressure Vessels & Piping Conf. Toronto, Canada, 2012. pp. 1–10.
21. S.Gourdet, F.Montheillet, Acta Mater., 2003, Vol.51, pp.2685-2699.10.1016/S1359-6454(03)00078-8 ↗
22. H.Gudmundsson, D.Brooks and J.A. Wert, Acta Metall. Mater., 1991, Vol.39, pp.19-35.10.1016/0956-7151(91)90325-U ↗
23. M.T. Lyttle and J.A. Wert, J. Mater. Sci., 1994, Vol.29, pp.3342-3350.10.1007/BF00356683 ↗
24. S. K. Albert, M. Matsui, T. Watanabe, H. Hongo, K. Kubo and M. Tabuchi, Int. J. Press. Vess. Pip., 2003,Vol. 80, pp.405–413.10.1016/S0308-0161(03)00072-3 ↗
25. D. Li, K. Shinozaki and H. Kuroki, Mater. Sci. Technol., 2003, Vol.19 (9), pp.1253–1260.10.1179/026708303225005926 ↗
26. S.T. Kimmins and D.J. Smith, J. Strain Anal., 1998, Vol.33, pp.195-206.10.1243/0309324981512913 ↗
27. H.Hongo, M. Tabuchi, Y. Liu and S. Tsukamoto, J. Soc. Mater. Sci. Japan, 2013, Vol.41, pp. 75-81.10.2472/jsms.62.75 ↗