journal article·2010-04

Strain-Rate Sensitivity and Failure Peculiarities in Compression of the Nanocrystalline Ni-20 Pct Fe Alloy at Low Temperatures

E.D. Tabachnikova, A.V. Podolskiy, V.Z. Bengus, S.N. Smirnov, H. Li, P.K. Liaw, H. Choo, K. Csach, J. Miskuf

Publisher page

Abstract

The strain-rate sensitivity of the applied stress was measured, and the values of the activation volume of the process of the plastic deformation V along the deformation curve in compression of the nanocrystalline (NC) Ni-20 pct Fe alloy (with average grain size ~22 nm) in the temperature range of 300 to 77 K (27 to −196 °C) were calculated. It was found that the decrease of the temperature from 300 to 77 K leads to a decrease of the value of V from 20 to 8 b3, and values of V do not depend on the strain. Fractographic features of the failure surfaces were studied in the temperature range 300 to 4.2 K (27 to −269 °C). Observed traces of melting on these surfaces at temperatures below 300 K indicate the intense heating in the catastrophic shear band of the alloy in the moment of failure. Causes of low-temperature decohesion along grain boundaries are discussed in terms of the sulfur segregation influence.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Surface Treatment and Residual Stress · Electromagnetic Effects on Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. H.S. Kim, Y. Estrin, and M.B. Bush: Acta Mater., 2000, vol. 48, pp. 493–504.10.1016/S1359-6454(99)00353-5 ↗
2. R.J. Asaro and S. Suresh: Acta Mater., 2005, vol. 53, pp. 3369–82.10.1016/j.actamat.2005.03.047 ↗
3. Y.M. Wang, A.V. Hamza, and E. Ma: Appl. Phys. Lett., 2005, vol. 86, pp. 2419171–73.
4. M.A. Meyers, A. Mishra, and D.J. Benson: Prog. Mater. Sci., 2006, vol. 51, pp. 427–556.10.1016/j.pmatsci.2005.08.003 ↗
5. J.K. Mason, A.C. Lund, and C.A. Schuh: Phys. Rev. B, 2006, vol. 73, pp. 054102–15.10.1103/PhysRevB.73.054102 ↗
6. H. Vehoff, D. Lemaire, K. Schuler, T. Waschkies, and B. Yang: Int. J. Mater. Res., 2007, vol. 98, pp. 259–68.10.3139/146.101464 ↗
7. W.M. Mook, M.S. Lund, C. Leighton, and W.W. Gerberich: Mater. Sci. Eng. A, 2008, vol. 493, pp. 12–20.10.1016/j.msea.2007.08.096 ↗
8. E.D. Tabachnikova, A.V. Podolskiy, V.Z. Bengus, S.N. Smirnov, M.I. Bidylo, H. Li, P.K. Liaw, H. Choo, K. Csach, and J. Miskuf: Mater. Sci. Eng. A, 2009, vol. 503, pp. 110–13.10.1016/j.msea.2008.02.052 ↗
9. A.G. Evans and R.D. Rawlings: Phys. Status Solidi, 1969, vol. 34, pp. 9–31.10.1002/pssb.19690340102 ↗
10. H. Li, F. Ebrahimi, H. Choo, and P.K. Liaw: J Mater. Sci., 2006, vol. 41, pp. 7636–42.10.1007/s10853-006-0856-3 ↗
11. H. Li and F. Ebrahimi: Mater. Sci. Eng. A, 2003, vol. 347, pp. 93–101.10.1016/S0921-5093(02)00586-5 ↗
12. E.D. Tabachnikova, A.V. Podolskiy, V.Z. Bengus, S.N. Smirnov, K. Csach, J. Miskuf, L.R. Saitova, I.P. Semenova, and R.Z. Valiev: Strength Mater., 2008, vol. 40, pp. 71–74.10.1007/s11223-008-0019-7 ↗
13. J.K. Heuer, P.R. Okamoto, N.Q. Lam, and J.F. Stubbins: Appl. Phys. Lett., 2000, vol. 76, pp. 3403–05.10.1063/1.126660 ↗
14. M. Yamaguchi, M. Shiga, and H. Kaburaki: Science, 2005, vol. 307 (5708), pp. 393–97.10.1126/science.1104624 ↗
15. W.T. Geng, J.-S. Wang, and G.B. Olson: Science, 2005, vol. 309 (5741), p. 1677.10.1126/science.1112072 ↗
16. H.J. Klam, H. Hahn, and H. Gleiter: Acta Metall., 1987, vol. 35 (8), pp. 2101–04.10.1016/0001-6160(87)90038-1 ↗
17. V.Z. Bengus, E.D. Tabachnikova, S.E. Shumilin, Y.I. Golovin, M.V. Makarov, A.A. Shibkov, J. Miskuf, K. Csach, and V. Ocelik: Int. J. Rapid Solidification, 1993, vol. 8, pp. 21–31.