journal article·2015-07

High-Temperature Workability of Thixocast A356 Aluminum Alloy

Shailesh Kumar Singh, K. Chattopadhyay, Pradip Dutta

Publisher page

Abstract

The present work highlights the role of globular microstructure on the workability of A356 aluminum alloy at elevated temperature. The hot deformation behavior was studied by isothermal hot compression tests in the temperature range 573 K to 773 K (300 A degrees C to 500 A degrees C) and strain rate range of 0.001 to 10 s(-1). The flow stress data obtained from the tests were used to estimate the strain rate sensitivity and strain rate hardening. Flow stress analysis of the alloy shows that the effect of temperature on strain hardening is more significant at lower strain levels and strain rate sensitivity is independent of strain. The results also reveal that the flowability of conventionally cast alloy increases after changing the dendritic microstructure into a globular structure through semisolid processing route. Thixocast alloy exhibits lower yield strength and higher elongation at elevated temperature in comparisons to conventionally cast values. This property has an important implication toward thixo-forming at an elevated temperature. (C) The Minerals, Metals & Materials Society and ASM International 2015
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. K.Siriporn, S. Wisutmethangoon, T. Plookpholi and J.Wannasin: JOM, 2008, vol.18, pp. 93-97.
2. M.C. Flemings and R. Mehrabian: AFS Transactions, 1973, vol.102, pp. 81-88.
3. T. Matsumiya and M.C. Flemings: Metall. Trans. B, 1981, vol. 21, pp. 17-31.10.1007/BF02674755 ↗
4. P. Kapranos, P.J. Ward, H.V. Atkinson and D.H. Kirkwood: Mater. Des., 2000, vol. 21(4), pp.387-94.10.1016/S0261-3069(99)00077-1 ↗
5. Z. Fan: Int. Mater. Rev., 2002, vol. 47(2), pp. 49-85.10.1179/095066001225001076 ↗
6. D. Brabazon, D.J. Browne and A.J. Carr: Mater. Sci. Eng. A, 2003, vol. 356, pp. 69-80.10.1016/S0921-5093(03)00158-8 ↗
7. S. N. Aqida, M. Maurel, D. Brabazon, S. Naher and M. Rosso: Int. J. Mater. Form., 2009, vol. 2, pp. 761- 64.10.1007/s12289-009-0540-7 ↗
8. S. K. Singh, K. Chattopadhyay, G. Phanikumar and P. Dutta: Acta Mater., 2014, vol.73, pp.177-85.10.1016/j.actamat.2014.04.019 ↗
9. S. Venugopal, S.L.Mannan, and Y.V.R.K. Prasad: Mater. Lett., 1992, vol. 15, pp.79-83.10.1016/0167-577X(92)90016-D ↗
10. S. Venugopal, S.L. Mannan, and Y.V.R.K Prasad: Mater. Sci. Eng. A, 1994, vol. 177, pp. 143–49.10.1016/0921-5093(94)90486-3 ↗
11. P.V. Sivaprasad, S.L Mannan and Y.V.R.K. Prasad: Mater. Sci. Technol., 2004, vol. 20, pp. 1545-50.10.1179/026708304X6031 ↗
12. B. Paul, R. Kapoor, J.K. Chakravartty., A.C. Bidaye, I.G. Sharma, and A.K. Suri: Scripta Mater., 2009, vol. 60, pp. 104–07.10.1016/j.scriptamat.2008.09.012 ↗
13. Y.V.R.K Prasad and K.P Rao: Mater. Sci. Eng. A, 2008, vol. 487, pp. 316–27.10.1016/j.msea.2007.10.038 ↗
14. K.P. Rao, Y.V.R.K. Prasad, N. Hort, and K.U. Kainer: J. Mater. Process. Technol., 2008 vol. 201, pp. 359–63.10.1016/j.jmatprotec.2007.11.148 ↗
15. Y.V.R.K Prasad and K.P. Rao: Mater. Sci. Eng. A, 2008, vol. 487, pp. 316-27.10.1016/j.msea.2007.10.038 ↗
16. Y. Niu, H. Hou, M. Li and Z. Li: Mater. Sci. Eng. A, 2008, vol. 492, pp. 24-28.10.1016/j.msea.2008.02.036 ↗
17. H.Z. Li, H.J. Wang, X.P. Liang, H.T. Liu, Y. Liu and X.M. Zhang: Mater. Sci. Eng. A, 2011, vol. 528, pp. 1548-52.10.1016/j.msea.2010.10.080 ↗
18. D.B. Spencer: PhD. Thesis, MIT, 1971.
19. D.B. Spencer, R. Mehrabian, and M.C. Flemings: Metall. Trans., 1972, vol.3, pp.1925-32.10.1007/BF02642580 ↗
20. M. C. Flemings, R. G. Riek and K. P. Young: Mater. Sci. Eng., 1976, vol. 25, pp. 103-17.10.1016/0025-5416(76)90057-4 ↗
21. J. Cheng, D. Apelian and R.D. Doherty: Metall. Trans. A, 1986, vol.17A, pp. 2049-62.10.1007/BF02645002 ↗
22. W. G. Cho and C. G. Kang: J.Mater. Process. Technol., 2000, vol. 105, pp. 269-77.10.1016/S0924-0136(00)00577-X ↗
23. E. J. Zoqui, M. Paes and E. Es-Sadiqi: J. Mater. Process.Technol., 2002, vol. 120, pp. 365-73.10.1016/S0924-0136(01)01148-7 ↗
24. H. V. Atkinson: Prog. Mater. Sci., 2005, vol. 50, pp. 341-412.10.1016/j.pmatsci.2004.04.003 ↗
25. G. Hirt and R. Kopp: Thixoforming, Semi-Solid Metal Processing, Wiley-VCH, New York, NY, 2009.10.1002/9783527623969 ↗
26. M.Theron, R.D. Knutsen, L.H. Ivanchev and H.P. Burger: J.Mater. Process. Technol., 2012, vol. 212, pp. 465-70.10.1016/j.jmatprotec.2011.10.010 ↗
27. Y.V.R.K. Prasad and S. Sasidhara: A Compendium of Processing Maps, ASM International, Metals Park, Ohio, 1997.
28. Y.V.R.K. Prasad, H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgan, K.A. Lark, and D.R. Barker: Metall. Trans. A, 1984, vol. 15, pp. 1883–92.10.1007/BF02664902 ↗
29. N. Ravichandran and Y.V.R.K. Prasad: Metall. Trans. A, 1991, vol. 22A, pp. 2339-48.10.1007/BF02665000 ↗
30. N. Srinivasan and Y.V.R.K. Prasad: Mater. Sci. Technol., 1992, vol. 8, pp. 206-12.10.1179/mst.1992.8.3.206 ↗
31. O. Sivakesavam, I.S. Rao and Y.V.R.K. Prasad: Mater. Sci. Technol., 1993, vol.9, pp.805-10.
32. S.V. Narayanamurthy, B. Nageswararao, and B.P. Kashyap: Int. Mater. Rev., 2000, vol.45, pp. 15-21.10.1179/095066000771048782 ↗
33. Y.V.R.K. Prasad, T. Seshacharyalu, S.C. Medeiors, and W.G. Frazier: Mater. Sci. Technol., 2000, vol.16, pp.511-16.10.1179/026708300101508171 ↗
34. D. Padmavardhani and Y.V.R.K. Prasad: Metall. Trans. A, 1991, vol. 22A, pp. 2985–92.10.1007/BF02650258 ↗