journal article·2005-03

Through-thickness texture gradient in an annealed Al-Mg alloy sheet

Jiantao Liu, S. W. Banovic, F. S. Biancaniello, R. D. Jiggetts

Publisher page

Abstract

Through-thickness crystallographic texture of a rolled and subsequently annealed Al-Mg continuous cast (CC) alloy was examined. Results showed that the annealed sheet developed a through-thickness texture gradient with the form of a stronger cube texture at the surface when compared to the center layers and varied R orientations through the thickness. While the through-thickness texture gradient was not attributed to the shear related texture, it was still related to the extent of deformation within the sheet.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. I.L. Dillmore and W.T. Roberts: J. Inst. Met., 1963–64, vol. 92, pp. 193–99.
2. N. Hansen and H. Mecking: in ICOTOM 4, G.J. Davies, I.L. Dillamore, R.C. Hudd, and J.S. Kallend, eds., The Metals Society, London, 1975, pp. 34–46.
3. R.E. Bauer, H. Mecking, and K. Lüke: Mater. Sci. Eng., 1977, vol. 27, pp. 163–80.10.1016/0025-5416(77)90168-9 ↗
4. H.O. Asbeck and H. Mecking: Mater. Sci. Eng., 1978, vol. 34, pp. 111–19.10.1016/0025-5416(78)90041-1 ↗
5. W. Truszkowski, J. Król, and B. Major: Metall. Trans. A, 1980, vol. 11A, pp. 749–58.10.1007/BF02661204 ↗
6. W. Truszkowski, J. Król, and B. Major: Metall. Trans. A, 1982, vol. 13A, pp. 665–69.10.1007/BF02644432 ↗
7. H.P. Kneijnsberg, C.A. Verbraak, and M.J. Ten Bouwhuijs: Acta Metall., 1985, vol. 33, pp. 1759–67.10.1016/0001-6160(85)90170-1 ↗
8. C.S. Lee and B.J. Duggan: Metall. Trans. A, 1991, vol. 22A, pp. 2637–43.10.1007/BF02851357 ↗
9. B. Major: Mater. Sci. Technol., 1992, vol. 8, pp. 510–15.10.1179/mst.1992.8.6.510 ↗
10. C.-H. Choi, J.W. Kwon, K.H. Oh, and D.N. Lee: Acta Mater., 1997, vol. 45, pp. 5119–28.10.1016/S1359-6454(97)00169-9 ↗
11. W. Mao: Mater. Sci. Eng., 1998, vol. A257, pp. 171–77.10.1016/S0921-5093(98)00836-3 ↗
12. C.-H. Choi and D.N. Lee: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 2217–22.10.1007/s11661-997-0179-2 ↗
13. O.-V. Mishin, B. Bay, and D.J. Jensen: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1653–62.10.1007/s11661-000-0175-2 ↗
14. M. Höscher, D. Raabe, and K. Lüke: Acta Metall. Mater., 1994, vol. 42, pp. 879–86.10.1016/0956-7151(94)90283-6 ↗
15. “Metals Test Methods and Analytical Procedures”: in Annual Book of ASTM Standards, ASTM INTERNATIONAL, West Conshohocken, PA, 2003, pp. 427–50.
16. L.G. Schulz: J. Appl. Phys., 1949, vol. 20, pp. 1033–36.10.1063/1.1698269 ↗
17. H.J. Bunge: Texture Analysis in Material Science, 1st ed., Butterworths and Co., London, 1982.
18. S. Matthies and G.W. Vinel: Phys. Stat. Sol. B, 1961, vol. 112, pp. K111-K114.10.1002/pssb.2221120254 ↗
19. J.S. Kallend, U.F. Kocks, A.D. Rollett, and H.-R. Wenk: Mater. Sci. Eng., 1991, vol. A132, pp. 1–11.10.1016/0921-5093(91)90355-Q ↗
20. M. Somerday and F.J. Humpreys: Mater. Sci. Technol., 2003, vol. 19, pp. 20–29.10.1179/026708303225008590 ↗
21. J. Liu and J.G. Morris: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2029–32.10.1007/s11661-003-0169-y ↗
22. J. Liu and J.G. Morris: Mater. Sci. Eng. A, 2004, vol. 385, pp. 342–51.10.1016/j.msea.2004.06.070 ↗
23. J. Liu: Ph.D. Thesis, University of Kentucky, Lexington, KY, 2003.
24. J. Pospiech and K. Lüke: Acta Metall., 1975, vol. 23, pp. 997–1007.10.1016/0001-6160(75)90014-0 ↗
25. O. Engler: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1517–27.10.1007/s11661-999-0088-7 ↗
26. J. Grewen and M.V. Heimendahl: Z. Metallkd., 1968, vol. 59, pp. 205–12.
27. H. Ahlborn, E. Hornbogen, and U. Köter: J. Mater. Sci., 1969, vol. 4, pp. 944–50.10.1007/BF00555308 ↗
28. J. Hirsch and K. Lüke: Acta Metall., 1985, vol. 33, pp. 1927–38.10.1016/0001-6160(85)90015-X ↗