journal article·2012-12

Origin and Propagation of Splits in High-Strength Low-Alloy Strip Steel

Rachel Punch, Martin Strangwood, Claire Davis

Publisher page

Abstract

A high-strength strip steel (yield strength of ~700 MPa) with a ductile-brittle transition over a wide temperature range shows splits (fissures) on the fracture surfaces in the upper transition region. The steel, hot rolled to strip thicknesses of approximately 10.0 mm and 16.8 mm, had a predominantly fine-grained ferrite microstructure with some coarse grain patches (area percent of 11 pct and 42 pct, respectively). Low-blow Charpy tests were carried out at room temperature, corresponding to the upper transition region for these strips. The low-blow tests resulted in the formation of splits without main crack propagation from the notch; therefore, the energies at which the splits initiated could be determined. Acoustic emission (AE) sensors were used during low-blow Charpy testing of the strip steels and mild steel (where no splits occur); it was found that AE was able to detect signals from the hammer impact, split formation, and ductile deformation. Optical microscopy, scanning electron microscopy (SEM), and X-ray tomography were carried out, which verified the presence of splits and showed that they propagated by transgranular cleavage, preferentially following coarse-grained regions. No significant difference in the number or length of splits between the 10- and 16.8-mm strip was observed, but the 10-mm strip did produce deeper splits during the low-blow Charpy testing. The deeper splits contribute to a lower impact transition temperature for the 10-mm strip material.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. R.J. Klassen, M.N. Bassim, M.R. Bayoumi, and H.G.F. Wilsdorf: Mater. Sci. Eng., 1986, vol. 1, no. 80, pp. 25–35.10.1016/0025-5416(86)90299-5 ↗
2. D.A. Curry: Mater. Sci. Eng., 1980, vol. 44, pp. 285–90.10.1016/0025-5416(80)90128-7 ↗
3. R. Song, D. Ponge, and D. Raabe: Acta Mater., 2005, vol. 18, no. 53, pp. 4881–92.10.1016/j.actamat.2005.07.009 ↗
4. B. Mintz, E. Maina, and W.B. Morrison: Mater. Sci. Eng., 2007, vol. 3, no. 23, pp. 347–54.
5. P. Shanmugam and S.D. Pathak: Eng. Fract. Mech., 1996, vol. 6, no. 53, pp. 991–1005.10.1016/0013-7944(95)00159-X ↗
6. T.L. Anderson, ed.: Fracture Mechanics: Fundamentals and Applications, CRC Press, Boca Raton, FL, 1994.
7. J.F. Knott: Fundamentals of Fracture Mechanics, The Butterworth Group, Bath, U.K., 1973.
8. Y. Kimura, T. Inoue, F. Yin, and K. Tsuzaki: Science, 2008, vol. 5879, no. 320, pp. 1057–60.10.1126/science.1156084 ↗
9. M. Yang, Y.J. Chao, X. Li, D. Immel, and J. Tan: Mater. Sci. Eng. A, 2008, vols. 1–2(497), pp. 462–70.10.1016/j.msea.2008.07.066 ↗
10. E. Almond: Metall. Trans., 1970, vol. 1, pp. 2038–41.10.1007/BF02642823 ↗
11. G. Baldi and G. Buzzichelli: Met. Sci., 1978, vol. 10, no. 12, pp. 459–72.10.1179/030634578790433332 ↗
12. M.R. Krishnadev, S. Dionne, and J. Morrisson: Mater. Charact., 1990, vol. 2, no. 24, pp. 169–78.10.1016/1044-5803(90)90034-H ↗
13. B.L. Bramfitt and A.R. Marder: Metall. Trans. A, 1977, vol. 8A, p. 1263.10.1007/BF02643841 ↗
14. W. Yan: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 159–71.10.1007/s11661-009-0068-y ↗
15. D.L. Bourell: Metall. Trans. A, 1983, vol. 14A, pp. 2487–96.10.1007/BF02668890 ↗
16. D.A. Curry: Met. Sci., 1980, vol. 14, pp. 319–26.10.1179/msc.1980.14.8-9.319 ↗
17. A. Echeverría and J.M. Rodriguez-Ibabe: Mater. Sci. Eng. A, 2003, vols. 1–2(346), pp. 149–58.
18. B. Mintz and W.B. Morrison: Mater. Sci. Eng., 2007, vol. 11, p. 23.
19. O.L. Towers: Met. Construct., 1986, vol. 3(18), pp. 171R–76R.
20. K. Wallin, T. Planman, M. Valo, D. Françcois, and A. Pineau: Fracture Mechanics Based Scaling Criteria for Miniature and Sub-Size Charpy-V Specimens, European Structural Integrity Society, Elsevier, Atlanta, GA, 2002, pp. 279–86.10.1016/S1566-1369(02)80031-0 ↗
21. A.C. Bannister: Sub task 3.3 report, Final Issue Determination of Fracture Toughness from Charpy Impact Energy: Procedure and Validation, British Steel, Rotherham, U.K.,1998.
22. BS7910, Guidance on Methods for Assessing the Acceptability of Flaws In Metallic Structures, 2005.
23. A.G. Kostryzhev, R.B. Punch, C.L. Davis, and M. Strangwood: Mater. Sci. Tech., 2012, vol. 2, no. 28, pp. 240–42.10.1179/1743284711Y.0000000024 ↗
24. J.-B. Ju, J.-S. Lee, and J.-I. Jang: Mater. Lett., 2007, vol. 29, no. 61, pp. 5178–80.10.1016/j.matlet.2007.04.007 ↗
25. M. Hatherley and W.C.B. Hutchinson: Introduction to Texture, Institution of Metallurgists, London, 1979.
26. G.J. Baczynski, J.J. Jonas, and L.E. Collins: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3045–54.10.1007/s11661-999-0215-5 ↗
27. T. Gladman: The Physical Metallurgy of Microalloyed Steels, The Institute of Materials, London, U.K., 1997.
28. B. Mintz, W.B. Morrison, and A. Jones: Met. Tech., 1979, vol. 6, pp. 252–60.10.1179/030716979803276246 ↗
29. B. Mintz, E.M. Maina, and W.B. Morrison: Inst. Mater. Miner. Min., 2008, vol. 2, no. 24, pp. 177–88.
30. D. Bhattacharjee and C.L. Davis: Scripta Mater., 2002, vol. 12, no. 47, pp. 825–31.10.1016/S1359-6462(02)00324-X ↗
31. D. Bhattacharjee, J.F. Knott, and C.L. Davis: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 121–30.10.1007/s11661-004-0115-7 ↗