Preservation of Geometrical Integrity of Supersolidus-Liquid-Phase-Sintered SKD11 Tool Steels Prepared with Powder Injection Molding
Source abstract
Abstract
The powder injection molded SKD11 tool steels often manifest shape retention problems during supersolidus liquid phase sintering due to the difficulties in controlling the amount of liquid phase. The typical temperature range for the sintering of SKD11 is only 10 K, between 1503 and 1513 K (1230 and 1240 °C), and this narrow sintering range demands a special furnace with very uniform temperature distribution. Through the addition of carbides, in particular TiC, this problem is resolved by enlarging the liquid + γ + carbide region in the phase diagram and by impeding the grain growth with the carbides. The resulting sintering window is broadened to 40 K, between 1513 and 1553 K (1240 and 1280 °C). The relevant mechanisms on the improvement of shape retention are discussed with a focus on the effect of carbide addition on the changes in the phase diagram and the microstructure. A guideline for the selection of effective carbides is also proposed based on the experimental results and the phase diagram analyses.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Powder Metallurgy Techniques and Materials · Injection Molding Process and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. H. Berns and A. Saltykova: Wear, 2009, vol. 267 (11), pp. 1791–97.10.1016/j.wear.2009.01.005 ↗
2. N.S. Myers and R.M. German: Int. J. Powder Metall., 1999, vol. 35 (6), pp. 45–51.
3. H. Miura, H. Morikawa, Y. Kawakami, and A. Ishibashi: J. Jpn. Soc. Powder Powder Metall., 1998, vol. 45 (5), pp. 436–41.10.2497/jjspm.45.436 ↗
4. S. Hachiga and Y. Shiina: J. Jpn. Soc. Powder Powder Metall., 2005, vol. 52 (10), pp. 717–21.10.2497/jjspm.52.717 ↗
5. H. Nakayama, H. Kyogoku, and S. Komatsu: J. Jpn. Soc. Powder Powder Metall., 2000, vol. 47 (12), pp. 1272–76.10.2497/jjspm.47.1272 ↗
6. H. Kyogoku, S. Komatsu, and H. Nakayama: J. Jpn. Soc. Powder Powder Metall., 1999, vol. 46 (8), pp. 853–57.10.2497/jjspm.46.853 ↗
7. R.M. German: Int. J. Powder Metall., 1990, vol. 26 (1), pp. 23–34.
8. R. Raman and R.M. German: Metall. Trans. A, 1995, vol. 26A, pp. 653–59.10.1007/BF02663915 ↗
9. R.M. German: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1553–67.10.1007/s11661-997-0217-0 ↗
10. G. Herranz, B. Levenfeld, and A. Várez: Mater. Sci. Forum, 2007, vols. 534–536 (1), pp. 353–56.10.4028/www.scientific.net/MSF.534-536.353 ↗
11. C.S. Wright, M. Youseffi, A.S. Wronski, I. Ansara, M. Durand-Charre, J. Mascarenhas, M.M. Oliveira, F. Lemoisson, and Y. Bienvenu: Powder Metall., 1999, vol. 42 (2), pp. 131–46.10.1179/003258999665486 ↗
12. J. Liu, A. Lal, and R.M. German: Acta Mater., 1999, vol. 47 (18), pp. 4615–26.10.1016/S1359-6454(99)00320-1 ↗
13. S. Talacchia, J.I. San Martin, I. Urrutibeaskoa, S. Jauregi, R. Palma, V. Martinez, and J.J. Urcola: Powder Metall., 1993, vol. 36 (4), pp. 275–80.10.1179/pom.1993.36.4.275 ↗
14. Z. Y. Liu, N.H. Loh, K.A. Khor, and S.B. Tor: Mater. Sci. Eng. A, 2001, vol. 311, pp. 13–21.10.1016/S0921-5093(01)00929-7 ↗
15. J.D. Bolton and A.J. Gant: Powder Metall., 1997, vol. 40 (2), pp. 143–50.10.1179/pom.1997.40.2.143 ↗
16. T. Tsuchiyama, S. Takaki, and S. Nakamura: J. Iron Steel Inst. Jpn., 1995, vol. 81 (2), pp. 147–52.10.2355/tetsutohagane1955.81.2_147 ↗
17. G. Herranz, G. Rodriguez, and R. Alonso: Proc. PM2010 World Congr., European Powder Metallurgy Association, Shrewsbury, United Kingdom, 2010, vol. 4, pp. 363–67.
18. J.A. Jiménez, M. Carsí, G. Frommeyer, and O.A. Runao: Powder Metall., 2005, vol. 48 (4), pp. 371–76.10.1179/174329005X79832 ↗
19. S. Weber, W. Theisen, F. Castro, and A. Pyzalla: Mater. Sci. Eng. A, 2009, vol. 515, pp. 175–82.10.1016/j.msea.2009.02.056 ↗
20. C.S. Wright, A.S. Wronski, and I. Iturriza: Mater. Sci. Technol., 2000, vol. 16, pp. 945–57.10.1179/026708300101508793 ↗