journal article·2007-12Open access

Dynamic Torsional Deformation Behavior of Ultra-Fine-Grained Dual-Phase Steel Fabricated by Equal Channel Angular Pressing

Byoungchul Hwang, Yang Gon Kim, Sunghak Lee, Duck Young Hwang, Dong Hyuk Shin

Abstract

Dynamic torsional deformation behavior of an ultra-fine-grained dual-phase steel fabricated by equal channel angular pressing (ECAP) was investigated and compared with that of an equal channel angular pressed (ECAPed) ultra-fine-grained low-carbon steel. Tensile and dynamic torsional tests were conducted on these two steels, and the deformed microstructures were observed to investigate the dynamic deformation behavior. The ECAPed low-carbon steel consisted of very fine, elongated ferrite-pearlite grains of 0.5 μm in size, and the ECAPed dual-phase steel consisted of ferrite-martensite grains of 1 μm in size. The dynamic torsional test results indicated that maximum shear stress of the dual-phase steel was lower than that of the conventional steel, but that fracture shear strain was higher in the dual-phase steel. Some adiabatic shear bands were observed at the gage center of the dynamically deformed torsional specimen of the low-carbon steel, but they were not observed in the dual-phase steel because localized deformation was alleviated by the increased strain hardenability. These results suggested that the ECAPed ultra-fine-grained dual-phase steel could be a good way to increase the fracture resistance under dynamic loading as the formation of adiabatic shear bands was reduced or prevented.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. R.Z. Valiev, R.K. Islamgaliev, I.V. Alexandrov: Prog. Mater. Sci., 2000, vol. 45, pp. 103–8910.1016/S0079-6425(99)00007-9 ↗
2. N.A. Akhmadeev, N.P. Kobelev, R.R. Mulyukov, Y.M. Soifer, R.Z. Valiev: Acta Metall. Mater., 1993, vol. 41, pp. 1041–4610.1016/0956-7151(93)90153-J ↗
3. K.T. Park, Y.S. Kim, J.G. Lee, D.H. Shin: Mater. Sci. Eng., 2000, vol. A293, pp. 165–7210.1016/S0921-5093(00)01220-X ↗
4. D.H. Shin, Y.S. Kim, E.J. Lavernia: Acta Mater., 2001, vol. 49, pp. 2387–9310.1016/S1359-6454(01)00165-3 ↗
5. D. Jia, K.T. Ramesh, E. Ma: Acta Mater., 2003, vol. 51, pp. 3495–50910.1016/S1359-6454(03)00169-1 ↗
6. R.Z. Valiev, R.R. Mulyukov, V.V. Ovchinnikov, V.A. Shabashov: Scripta Mater., 1991, vol. 25, pp. 2717–2210.1016/0956-716X(91)90145-Q ↗
7. R.Z. Valiev, T.G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881–98110.1016/j.pmatsci.2006.02.003 ↗
8. Y. Wang, M. Chen, F. Zhou, E. Ma: Nature, 2002, vol. 419, pp. 912–1510.1038/nature01133 ↗
9. K.T. Park, D.H. Shin: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 705–0710.1007/s11661-002-0134-1 ↗
10. S.-T. Oh, H.-J. Chang, K.H. Oh, H.N. Han: Met. Mater. Int., 2006, vol. 12, pp. 121–2910.1007/BF03027467 ↗
11. A. Marchand, J. Duffy: J. Mech. Phys. Solids, 1988, vol. 36, pp. 251–8310.1016/0022-5096(88)90012-9 ↗
12. K. Cho, S. Lee, S.R. Nutt, J. Duffy: Acta Mater., 1993, vol. 41, pp. 923–3210.1016/0956-7151(93)90026-O ↗
13. Y. Shiota, Y. Tomota, A. Moriai, T. Kamiyama: Met. Mater. Int., 2005, vol. 11, pp. 371–7610.1007/BF03027507 ↗
14. C.G. Lee, K.J. Kim, S. Lee, K. Cho: Metall. Trans. A, 1998, vol. 29A, pp. 469–7610.1007/s11661-998-0127-9 ↗
15. G.T. Gray, T.C. Lowe, C.M. Cady, R.Z. Valiev, I.V. Aleksandrov: Nanostruct. Mater., 1997, vol. 9, pp. 477–8010.1016/S0965-9773(97)00104-9 ↗
16. Q. Wei, L. Kecskes, T. Jiao, K.T. Hartwig, K.T. Ramesh, E. Ma: Acta Mater., 2004, vol. 52, pp. 1859–6910.1016/j.actamat.2003.12.025 ↗
17. M. Furukawa, Z. Horita, T.G. Langdon: Met. Mater. Int., 2003, vol. 9, pp. 141–4910.1007/BF03027270 ↗
18. D.H. Shin, I. Kim, J. Kim: Met. Mater. Int., 2002, vol. 8, pp. 513–1810.1007/BF03178251 ↗
19. D.H. Shin, S.Y. Han, K.T. Park, Y.S. Kim, Y.N. Park: Mater. Trans. JIM, 2003, vol. 44, pp. 1630–3510.2320/matertrans.44.1630 ↗
20. Y.I. Son, Y.K. Lee, K.T. Park, C.S. Lee, D.H. Shin: Acta Mater., 2005, vol. 53, pp. 3125–3410.1016/j.actamat.2005.02.015 ↗
21. M.E. Backman, S.A. Finnegan: in Metallurgical Effects at High Strain Rates, R.W. Rohde, B.M. Butcher, J.R. Holland, C.H. Karnes, eds., Plenum Press, New York, NY, 1973, pp. 531–4310.1007/978-1-4615-8696-8_30 ↗
22. H.C. Rogers, C.V. Shastry: Shock Waves and High-Strain-Rate Phenomena in Metals, M.A. Mayers, L.E. Murr, eds., Plenum Press, New York, NY, 1981, pp. 285–9810.1007/978-1-4613-3219-0_18 ↗
23. Y. Bai, B. Dodd: Adiabatic Shear Localization—Occurrence, Theories and Applications, Pergamon Press, Oxford, 1992, pp. 1–20
24. K. Cho, Y.C. Chi, J. Duffy: Metall. Trans. A, 1990, vol. 21A, pp. 1161–7510.1007/BF02656536 ↗
25. W.Y. Yeung, B.J. Duggan: Mater. Sci. Technol., 1986, vol. 2, pp. 552–5810.1179/mst.1986.2.6.552 ↗
26. B. Hwang, H.S. Lee, Y.G. Kim, S. Lee, B.D. Ahn, D.H. Shin, C.G. Lee: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 389–9710.1007/s11661-005-0310-1 ↗
27. M.A. Meyers: Dynamic Behavior of Materials, John Wiley & Sons, New York, NY, 1994, pp. 448–8710.1002/9780470172278.ch15 ↗
28. D.K. Kim, S.Y. Kang, S. Lee, K.J. Lee: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 81–9210.1007/s11661-999-0197-3 ↗
29. H.S. Lee, B. Hwang, S. Lee, C.G. Lee, S.J. Kim: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2371–8210.1007/s11661-006-0217-5 ↗
30. S.P. Timothy, I.M. Hutching: Acta Metall., 1985, vol. 33, pp. 667–7610.1016/0001-6160(85)90030-6 ↗
31. I.A. El-Sesy, Z.M. El-Baradie: Mater. Lett., 2002, vol. 57, pp. 580–8510.1016/S0167-577X(02)00833-9 ↗
32. N.J. Kim, G. Thomas: Metall. Trans. A, 1981, vol. 12A, pp. 483–8910.1007/BF02648546 ↗
33. G. Thomas, J.Y. Koo: in Structure and Properties of Dual-Phase Steels, R.A. Kot, J.W. Morris, eds., AIME, New York, NY, 1979, pp. 183–201
34. I.D. Choi, D.M. Kim, S.J. Kim, D.M. Bruce, D.K. Matlock, J.G. Speer: Met. Mater. Int., 2006, vol. 12, pp. 13–1910.1007/BF03027517 ↗