Improvement of Drawability of Titanium-Stabilized Interstitial-Free Steel by Optimization of Process Parameters and Texture
Source abstract
Abstract
A detailed study on the effect of cold rolling and annealing temperature on the texture and drawability of Ti-stabilized interstitial-free (IF) steels have been made with a view to achieving high drawability. The presence of shear type and cold-deformation type of textures in the hot bands of 3.8-, 4.3- and 4.5-mm thickness has been attributed to finish rolling below the Ar 3 temperature. The 4.5-mm hot band was selected for further studies as it showed a strong γ fiber. Cold rolling of the hot band was done in the range of 60 to 90 pct, followed by batch annealing in the range of 660 °C to 750 °C. For a particular annealing temperature, a maximum in the intensity of $$ {\left\{ {{\text{111}}} \right\}}{\left\langle {{\text{110}}} \right\rangle } $$ component, and in average normal anisotropy, an r m value was observed with the increase in cold reduction, followed by a drop with further cold reduction. The results are discussed in terms of orientation distribution function (ODF), recrystallization behavior, and precipitation of FeTiP, (Ti, Mn) S, and TiC particles. Fine FeTiP-type precipitates in the grains and at the grain boundaries in samples annealed at 660 °C, as well as samples associated with (Ti, Mn)S in samples annealed at 750 °C, were found to be detrimental for the development of beneficial γ fiber and improved drawability, while coarse FeTiP-type precipitates in 80 pct cold-reduced samples annealed at 680 °C and 710 °C resulted in maximum r m values of 2.29 and 2.25, respectively. The dissolution of TiC at an annealing temperature of 750 °C adversely affected drawability due to the solute drag effect of solute carbon. An optimized combination of cold reduction and annealing temperature has been established for achieving a uniform γ fiber along with high r m values.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Forming Simulation Techniques · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. W.B. Hutchinson: Int. Mater. Rev., 1984, vol. 29 (1), pp. 25–42
2. H.J. Bunge: Theoretical Methods of Texture Analysis, DGM Informationsgesellschaft, Deutsche Gesellschaft fur Matallkunde, Frankfurt, Germany, 1987
3. M. Holscher, D. Raabe, K. Lucke: Steel Res., 1991, vol. 62, pp. 567–7510.1002/srin.199100451 ↗
4. U.F. Kocks, C.N. Tome, H.-R. Wenk: Texture and Anisotropy, Cambridge University Press, Cambridge, United Kingdom, 1998
5. I. Gupta and D. Bhattacharya: Proc. Symp. on Metallurgy of Vacuum-Degassed Steel Products, Indianapolis, IN, October 3–5, 1989, TMS, Warrendale, PA, 1990, pp. 43–72
6. A. Najafi-Zadeh, J.J. Jonas, S. Yue: Metall. Trans. A, 1992, vol. 23A, pp. 2607–1710.1007/BF02658064 ↗
7. S.V. Subramanian, M. Prikryl, A. Ulabhaje, and K. Balasubramanian: Proc. Int. Conf. on IF Steel Sheet, Canadian Institute Mining, Metallurgical and Petroleum, Ottawa, Ontario, Canada, August 19–20, 1991, pp. 15–38
8. S. Sangai: Curr. Adv. Mater. Proc., 1990, vol. 3, pp. 1768–71
9. H. Ohtani, N. Hanaya, M. Hasebe, S. Teraoka, and M. Abe: Calphad, 2006, vol. 30 (2), pp. 147–5810.1016/j.calphad.2005.09.006 ↗
10. C. Brun, P. Patou, and P. Parniere: Proc. Symp. on Metallurgy of Continuous-Annealed Sheet Steel, Dallas, TX, 1982, TMS-AIME, Warrendale, PA, February 14–18, 1982, pp. 173–97
11. J. Shi, X. Wang: J. Mater. Eng. Perform., 1999, vol. 8 (6), p. 64110.1361/105994999770346396 ↗
12. T. Irie, S. Satoh, A. Yasuda, and O. Hashimito: Proc. Symp. on Metallurgy of Continuous-Annealed Sheet Steel, Dallas, TX, 1982, TMS-AIME, Warrendale, PA, 1982, pp. 155–71
13. A. Okamoto and N. Mizui: Proc. Symp. on Metallurgy of Vacuum Degassed Steel Products, TMS, Warrendale, PA, October 3–5, 1989, pp. 161–80
14. I. Tsukatani: ISIJ Int., 1998, vol. 38 (6), pp. 625–3210.2355/isijinternational.38.625 ↗
15. M. Ferry, D. Yu, T. Chandra: ISIJ Int., 2001, vol. 41 (8), pp. 876–8210.2355/isijinternational.41.876 ↗
16. S. Yim, P. Wray, K.M. Tiitto, C.I. Garcia, A.J. DeArdo: ISIJ Int., 2003 vol. 43 (10), pp. 1615–2110.2355/isijinternational.43.1615 ↗
17. V.J. Martinez, J.I. Verdeja, J.A. Pero-Sanz: Mater. Charact., 2001, vol. 46, pp. 45–5310.1016/S1044-5803(00)00092-9 ↗
18. Y. Nagataki, Y. Hosoya: ISIJ Int., 1996, vol. 36 (4), pp. 451–6010.2355/isijinternational.36.451 ↗
19. M.P. Butron-Guillen, J. Jonas: ISIJ Int., 1996, vol. 36 (1), pp. 68–7310.2355/isijinternational.36.68 ↗
20. T. Senuma, H. Yada, R. Simizu, J. Harase: Acta Metall. Mater., 1990, vol. 38 (12), pp. 2673–8110.1016/0956-7151(90)90281-K ↗
21. S.H. Lee, D.N. Lee: Mater. Sci. Eng., 1998, vol. A249, pp. 84–9010.1016/S0921-5093(98)00588-7 ↗
22. D. Raabe, K. Lucke: Scripta Metall., 1992, vol. 26 (8), pp. 1221–2610.1016/0956-716X(92)90567-X ↗
23. Y.B. Park, D.N. Lee, G. Gottstein: J. Mater. Process. Technol., 1994, vol. 45, pp. 471–7610.1016/0924-0136(94)90384-0 ↗
24. K. Okuda, Y. Kawabata, K. Sakata, and T. Obara: Proc. 39th Mechanical Working and Steel Processing Conf. XXXV, ISS, Warrendale, PA, 1998, p. 297
25. Z. Wang, X. Wang: J. Mater. Proc. Technol., 2001, vol. 113, pp. 659–6110.1016/S0924-0136(01)00593-3 ↗
26. N. Matsudzu, K. Koyama, T. Takahashi, H. Okhashi, M. Shibata: CAMP-ISIJ, 1990, vol. 3, p. 1816
27. P. Van Houtte: User Manual, MTM-FHM Software, Version 2, MTM-KU Leuven, ed., Belgium, 1996
28. Y.B. Park, D.N. Lee, G. Gottstein: J. Mater. Process. Technol., 1994, vol. 45, pp. 471–7610.1016/0924-0136(94)90384-0 ↗
29. M. Ferry, D. Yu, T. Chandra: ISIJ Int., 2001, vol. 41 (8), pp. 876–8210.2355/isijinternational.41.876 ↗
30. V.J. Martinez, J.I. Verdeja, J.A. Pero-Sanz: Mater. Charact., 2001, vol. 46, pp. 45–5310.1016/S1044-5803(00)00092-9 ↗
31. B.K. Panigrahi: Bull. Mater. Sci., 2001, vol. 24 (4), pp. 361–7110.1007/BF02708632 ↗
32. D. Raabe, K. Lucke: Scripta Metall. Mater., 1992, vol. 26 (8), pp. 1221–2610.1016/0956-716X(92)90567-X ↗
33. M. Holscher: Ph.D. Thesis, RWTH, Aachen, Germany, 1987
34. M. Holscher: Proc. Int. Conf. Textures of Materials ICOTOM 9, Avigon, France, 1990
35. S.H. Lee, D.N. Lee: Mater. Sci. Eng., 1998, vol. A249, pp. 84–9010.1016/S0921-5093(98)00588-7 ↗
36. I. Samajdar, B. Verlinden, P. Vanhoutte, D. Vanderschueren: Scripta Mater., 1997, vol. 37 (6), pp. 869–7410.1016/S1359-6462(97)00185-1 ↗
37. R. Vogel, B. Giessen: Arch. Eisenhüttenwes., 1959, vol. 30, pp. 565–7610.1002/srin.195903080 ↗
38. K. Banerjee: Tata Steel, Jamshedpur, India, unpublished research, 2006
39. S. Hinotani, J. Endo, T. Takayama, N. Mizui, Y. Inokuma: ISIJ Int., 1994, vol. 34, pp. 17–2310.2355/isijinternational.34.17 ↗
40. A. Belyansky, V. Kapnin, Y. Larin, and N. Fonstein: Proc. Int. Forum on “Physical Metallurgy of IF Steel,” Iron and Steel Institute of Japan, Tokyo, 1994, pp. 289–92
41. M. Hatherley and W.B. Hutchinson: An Introduction to Textures in Metals, Monograph No. 5, The Institute of Metallurgists, Chameleon Press Limited, London, 1979