journal article·2011-12

Wear Behavior of the Lead-Free Tin Bronze Matrix Composite Reinforced by Carbon Nanotubes

Jun Zeng, Huiqing Fan, Yangli Wang, Siquan Zhang

Publisher page

Abstract

Copper-coated carbon nanotubes were prepared by the electroless plating route. The structure and component of copper/carbon tubes were characterized using a transmission electron microscope and energy dispersive spectrometer. The results show that the surface of the carbon tubes was covered by the copper particles. Copper/carbon tubes were used as the substitute of part of tin and all of lead in the tin bronze matrix, and the tribological properties of carbon nanotube-reinforced Cu-4 wt pct Sn-6 wt pct Zn composites were studied. The effects of the carbon nanotube volume fraction and sliding distance in unlubricated ball-on-disc wear test were investigated. The 3 vol pct carbon nanotube-reinforced Cu-4 wt pct Sn-6 wt pct Zn composite shows the Vickers hardness of 126.9, which is approximately 1.6 times higher than that of Cu-6 wt pct Sn-6 wt pct Zn-3 wt pct Pb tin bronze. The wear rate and average friction coefficients of 3 vol pct carbon nanotube-reinforced Cu-4 wt pct Sn-6 wt pct Zn composite were lower than those of the Cu-6 wt pct Sn-6 wt pct Zn-3 wt pct Pb tin bronze, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Electrodeposition and Electroless Coatings · Carbon Nanotubes in Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. S. Iijima: Nature, 1991, vol. 354, pp. 56-58.10.1038/354056a0 ↗
2. M. Terrones: Ann. Rev. Mater. Res., 2003, vol. 33, p. 419.10.1146/annurev.matsci.33.012802.100255 ↗
3. R.H. Baughman, A.A. Zakhidov, and W.A.D. Heer: Science, 2002, vol. 297, pp. 787-92.10.1126/science.1060928 ↗
4. P. Calvert: Nature, 1999, vol. 399, pp. 210-11.10.1038/20326 ↗
5. E.W. Wong, P.E. Sheehan, and C.M. Lieher: Science, 1997, vol. 277, pp. 1971-75.10.1126/science.277.5334.1971 ↗
6. L. Hyunseop, P. Boumyoung, and J. Haedo: J. Mater. Process Tech., 2009, vol. 209, pp. 1729-35.10.1016/j.jmatprotec.2008.04.021 ↗
7. W.Y. Li, C.J. Li, and H.L. Liao: Appl. Surf. Sci., 2010, vol. 256, pp. 4953-58.10.1016/j.apsusc.2010.03.008 ↗
8. M. Ciopec, C. Muntean, A. Negrea, L. Lupa, and P. Negrea: Thermochim. Acta, 2009, vol. 488, pp. 10-16.10.1016/j.tca.2009.01.011 ↗
9. G. Orhan and G. Hapal: Powder Technol., 2010, vol. 201, pp. 57-63.10.1016/j.powtec.2010.03.003 ↗
10. U. Ozsarac, F. Findik, and M. Durman: Mater. Des., 2007, vol. 28, pp. 345-50.10.1016/j.matdes.2005.05.017 ↗
11. B.S. Unlu, E. Atik, and C. Meric: Mater. Des., 2007, vol. 28, pp. 2160-65.10.1016/j.matdes.2006.07.011 ↗
12. M. Ghorbani, M. Mazaheri, and A. Afshar: Surf. Coat. Tech. 2005, vol. 190, pp. 32-38.10.1016/j.surfcoat.2004.04.092 ↗
13. H. Turhan, M. Aksoy, V. Kuzucu, and M.M. Yildirim: J. Mater. Process. Tech., 2001, vol. 114, pp. 207-11.10.1016/S0924-0136(01)00569-6 ↗
14. N.S. Poonawala, A.K. Chakrabarti, and A.B. Chattopadhyay: Wear, 1993, vol. 162, pp. 580-84.10.1016/0043-1648(93)90544-V ↗