journal article·2015-11

Assessment of Creep Strain Distribution Across Base Metal of 316LN Austenitic Stainless Steel Weld Joint by an EBSD-Based Parameter

V. D. Vijayanand, V. Ganesan, J. Ganesh Kumar, P. Parameswaran, Naveena, K. Laha

Publisher page

Abstract

Electron backscatter diffraction (EBSD) analysis has been used to estimate the accumulated strain in base metal region of 316LN austenitic stainless steel weld joints, creep tested at 923 K (650 °C), and at stresses of 175 and 225 MPa. The variation in strength of weld metal, heat-affected zone (HAZ), and base metal-induced stress and strain gradients across the weld joint under creep exposure. Finite element analysis (FEA) of von-Mises stress distribution across the joint has been carried out on incorporating strength of different constituents of the joint, derived by miniature specimen testing techniques. The FEA simulations revealed preferential accumulation of von-Mises stress in the base metal region near to HAZ. The variation in accumulated plastic strain across the base metal has been estimated using a ‘crystal deformation’ (C d) parameter which quantifies the orientation spread within a grain. This parameter was obtained by EBSD analysis carried out using a scanning electron microscope. The trend in variation of accumulated plastic strain across the base metal accounted well with the von-Mises stress variation, which causes plastic deformation. The plastic strain in the base metal in both the stress levels was found to accumulate preferentially near to the HAZ and reduced steadily toward the ridge at the end of specimen. Transmission electron microscopic study has been carried out to substantiate the findings of the EBSD investigation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. M. Kamaya, A.J. Wilkinson, and J.M. Titchmarsh: Nucl. Eng. Des., 2005, vol. 235, pp. 713-25.10.1016/j.nucengdes.2004.11.006 ↗
2. M. Kamaya: Fatigue Fract. Eng. Mater. Struct., 2009, vol. 33, pp. 94-104.10.1111/j.1460-2695.2009.01420.x ↗
3. J.A. Sutliff: Microsc. Microanal., 1999, vol. 2, pp. 236-37.10.1017/S1431927600014501 ↗
4. T.M. Angeliu, P.L. Andresen, E. Hall, J.A. Sutliff, and S. Sitzman: Corrosion-2000, Houston, 2000, Paper No. 186.
5. M.A. Othon, M.M. Morra, S. Ooki, and R.B. Rebak: ASME Pressure Vessels and Piping Conference, Paris, 2013, Paper No. PVP2013-97350.
6. K. Mino, R. Imamura, H. Koiwai, and C. Fukuoka: Adv. Eng. Mater., 2001, vol. 3, pp. 922-24.10.1002/1527-2648(200111)3:11<922::AID-ADEM922>3.0.CO;2-K ↗
7. L.N. Brewer, M.A. Othon, L.M. Young, and T.M. Angeliu: Microsc. Microanal., 2006, vol. 12, pp. 85-91.10.1017/S1431927606060120 ↗
8. D.N. Githinji, S.M. Northover, P.J. Bouchard, M.A. Rist: Mater. Metall. Trans. A, 2013, vol. 44, pp. 4150-67.10.1007/s11661-013-1787-7 ↗
9. S.L. Mannan, S.C. Chetal, B. Raj, and S.B. Bhoje: Trans. Indian Inst. Met., 2003, vol. 56, pp. 155-78.
10. J.A. Brooks and A.W. Thompson: Int. Mater. Rev., 1991, vol. 36, pp. 16-44.10.1179/imr.1991.36.1.16 ↗
11. F.C. Hull: Weld. J., 1967, vol. 46, pp. 399-409.
12. J.J. Smith and R.A. Farrar: Int. Mater. Rev., 1993, vol. 38, pp. 25-51.10.1179/imr.1993.38.1.25 ↗
13. S.R. Keown and R.G. Thomas: Met. Sci., 1981, vol. 15, pp. 386-92.10.1179/030634581790426886 ↗
14. M. Kamaya: Ultramicroscopy, 2011, vol. 111, pp. 1189–99.10.1016/j.ultramic.2011.02.004 ↗
15. S.I. Wright, M.M. Nowell, and D.P. Field: Microsc. Microanal., 2011, vol. 17, pp. 316-29.10.1017/S1431927611000055 ↗
16. A.J. Wilkinson and D.J. Dingley: Acta Metall. Mater., 1991, vol. 39, pp. 3047-55.10.1016/0956-7151(91)90037-2 ↗
17. S.I. Wright and M.M. Nowell: Microsc. Microanal., 2006, vol. 12, pp. 72-84.10.1017/S1431927606060090 ↗
18. B.S. El-Dasher, B.L. Adams, and A.D. Rollett: Scripta Mater., 2003, vol. 48, pp. 141-45.10.1016/S1359-6462(02)00340-8 ↗
19. S. Sun, B. L.Adams, and W.E. King: Philos. Mag. A, 2000, vol. 80, pp. 9-25.10.1080/01418610008212038 ↗
20. L. N. Brewer, D. P. Field, and C. C. Merriman: in Electron Backscatter Diffraction in Material Science, A.J. Schwarz, M. Kumar, B.L. Adams, and D.P. Field, eds., Kluwer Academic/Plenum Publishers, New York, 2000, pp. 251–62.
21. F.M. Haggag, R.K. Nanstad, J.T. Hutton, D.L. Thomas, and R.L. Swain: in Applications of Automated Technology to Fatigue and Fracture Testing, ASTM STP 1092, A.A. Braun, N.E. Ashbaugh, and F.M. Smith, eds., American Society for Testing and Materials, Philadelphia,1990, pp. 188–208.10.1520/STP25039S ↗
22. Naveena, V.D. Vijayanand, V. Ganesan, K. Laha, and M.D. Mathew: Mater. Sci. Eng. A, 2012, vol. 552, pp. 112-18.10.1016/j.msea.2012.05.017 ↗
23. O. Muransky, M.C. Smith, P.J. Bendeich, T.M Holden, V. Luzin, R.V. Martins, and L. Edwards: Int. J. of Solids Struct., 2012, vol. 49, pp. 1045-62.10.1016/j.ijsolstr.2011.07.006 ↗
24. V.D. Vijayanand, K. Laha, P. Parameswaran, V. Ganesan, and M.D. Mathew, Mater. Sci. Eng. A, 2014, vol. 607, pp. 138-44.10.1016/j.msea.2014.03.138 ↗
25. M. Kamaya, A. J. Wilkinson, and J. M. Titchmarsh: Acta Mater., 2006, vol. 54, pp. 539-48.10.1016/j.actamat.2005.08.046 ↗
26. K. Mino, C. Fukuoka, and H. Yoshizawa: J. Japan Inst. of Met., 2000, vol. 64, pp. 50-55.10.2320/jinstmet1952.64.1_50 ↗
27. C.F Etienne, D.V. Rossum, and F. Roode: Proceedings of the International Conference on Engineering Aspects of Creep, University of Sheffield, UK, 1980, vol. 2, pp. 113–21.
28. Naveena, V.D. Vijayanand, V. Ganesan, K. Laha, and M.D. Mathew: Mater. Sci. Technol., 2014, vol. 30, pp. 1223-28.
29. G. Sasikala, M.D. Mathew, K. B. S. Rao, and S. L. Mannan: Mater. Metall. Trans. A, 2000, vol. 31, pp. 1175-85.10.1007/s11661-000-0113-3 ↗
30. K. Laha, K.S. Chandravathi, K.B.S. Rao, S.L. Mannan, and D.H. Sastry: Mater. Metal. Trans. A, 2001, vol. 32, pp. 115-24.10.1007/s11661-001-0107-9 ↗
31. K. Laha, K.S. Chandravathi, P. Parameswaran, S. Goyal, and M.D. Mathew (2012) Mater. Metall. Trans. A 43:1174-1186.10.1007/s11661-011-0957-8 ↗
32. S. Goyal, K. Laha, K.S. Chandravathi, P. Parameswaran, and M.D. Mathew: Phil. Mag. A, 2011, vol. 91, pp. 3128-54.10.1080/14786435.2011.570279 ↗
33. E. Smith and J.T. Barnby: Met. Sci. J., 1967, vol. 1, pp. 56-64.10.1179/msc.1967.1.1.56 ↗
34. M.J. Manjoine: Weld. J., 1982, vol. 61, pp. 50-57.
35. O. Ajaja and A.J. Ardell: Philos. Mag. A, 1979, vol. 39, pp. 65-73.10.1080/01418617908239276 ↗
36. A. Belyakov, T. Sakai, and H. Miura (2000) Mater. Trans. JIM, 41: 476-84.10.2320/matertrans1989.41.476 ↗