journal article·2016-12

Effect of Preheating on the Inertia Friction Welding of the Dissimilar Superalloys Mar-M247 and LSHR

O. N. Senkov, D. W. Mahaffey, S. L. Semiatin

Publisher page

Abstract

Differences in the elevated temperature mechanical properties of cast Mar-M247 and forged LSHR make it difficult to produce sound joints of these alloys by inertia friction welding (IFW). While extensive plastic upset occurs on the LSHR side, only a small upset is typically developed on the Mar-M247 side. The limited plastic flow of Mar-M247 thus restricts the extent of “self-cleaning” and mechanical mixing of the mating surfaces, so that defects remain at the bond line after welding. In the present work, the effect of local preheating of Mar-M247 immediately prior to IFW on the welding behavior of Mar-M247/LSHR couples was determined. An increase in the preheat temperature enhanced the plastic flow of Mar-M247 during IFW, which resulted in extensive mechanical mixing with LSHR at the weld interface, the formation of extensive flash on both the Mar-M247 and LSHR sides, and a sound bond. Performed in parallel with the experimental work, finite-element-method (FEM) simulations showed that higher temperatures are achieved within the preheated sample during IFW relative to its non-preheated counterpart, and plastic flow is thus facilitated within it. Microstructure and post-weld mechanical properties of the welded samples were also established.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. R. Schafrik and R. Sprague: Adv. Mater. Process., 2004, vol. 162, pp. 27–30.
2. R.C. Reed: The Superalloys: Fundamentals and Applications, Cambridge University Press, Cambridge, 2006.10.1017/CBO9780511541285 ↗
3. M.J. Donachie and S.J. Donachie: Superalloys: A Technical Guide, 2nd ed., ASM International, Materials Park, 2002.10.31399/asm.tb.stg2.9781627082679 ↗
4. A. Chamanfar, M. Jahazi, and J. Cormier: Metall. Mater. Trans. A 2015, vol. 46A, pp. 1639–69.10.1007/s11661-015-2752-4 ↗
5. M. Preuss, A. Steuwer, P. J. Withers, G. J. Baxter, and S. Bray: Trends in Welding Research: Proceedings of the 6th International Conference, April 15, 2002–April 19, 2002, ASM International, Phoenix. 2002, pp. 886–90.
6. Z.W. Huang, H.Y. Li, M. Preuss, M. Karadge, P. Bowen, S. Bray, and G. Baxter: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1608–20.10.1007/s11661-007-9194-6 ↗
7. H.S. Jeong, J.R. Cho, and H.C. Park: Key Eng. Mater., 2007, vol. 345–346, pp. 1429–32.10.4028/www.scientific.net/KEM.345-346.1429 ↗
8. O.N. Senkov, D.W. Mahaffey, S. L. Semiatin, and C. Woodward: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 5545–61.10.1007/s11661-014-2512-x ↗
9. M. Sakaguchi, A. Sano, T.H. Tran, M. Okazaki, and M. Sekihara: J. Sol. Mech. Mater. Eng., 2008, vol. 2, pp. 1508–16.10.1299/jmmp.2.1508 ↗
10. M. Preuss, P.J. Withers, and G.J. Baxter: Mater. Sci. Eng. A, 2006, vol. 437A, pp. 38–45.10.1016/j.msea.2006.04.058 ↗
11. M. Maalekian: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 738–59.10.1179/174329307X249333 ↗
12. O.N. Senkov, D.W. Mahaffey, S.L. Semiatin, and C. Woodward: J. Mater. Eng. Perform., 2015, vol. 24, pp. 1173–84.10.1007/s11665-014-1379-8 ↗
13. S.L. Semiatin, K.E. MacClary, A.D. Rollett, C.G. Roberts, E.J. Payton, F. Zhang, and T.P. Cabb: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 2778–98.10.1007/s11661-013-1675-1 ↗
14. M. Kaufman: Fifth International Symposium on Superalloys, TMS, Warrendale. 1984, pp. 43–52.10.7449/1984/Superalloys_1984_43_52 ↗
15. T.P. Gabb, R.A. MacKay, S.L. Draper, C.K. Sudbrack, and M.V. Nathal: The Mechanical Properties of Candidate Superalloys for a Hybrid Turbine Disk, NASA/TM-2013-217901, NASA Glenn Research Center, Cleveland, 2013.
16. J.R. Kattus: Aerospace Structural Metals Handbook, Purdue Research Foundation, West Lafayette, 1999.
17. T.P. Gabb, J. Gayda, P.T. Kantzos, T. Biles, and W. Konkel: The tensile Properties of Advanced Nickel-Based Disk Superalloys During Quenching Heat Treatments, NASA/TM-2001-211218, NASA Glenn Research Center, Cleveland, 2001.
18. D.W. Mahaffey, O.N. Senkov, R. Shivpuri, and S.L. Semiatin: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 3981–4000.10.1007/s11661-016-3600-x ↗
19. JMatPro Practical Software for Materials Properties. http://www.sentesoftware.co.uk/jmatpro.aspx. Accessed 15 March, 2016.
20. T.P. Gabb and P.T. Kantzos: Thermal and Mechanical Property Characterization of the Advanced Disk Alloy LSHR, NASA/TM-2005-213645, NASA Glenn Research Center, Cleveland, 2005.
21. I. Wang, M. Preuss, P.J. Withers, G. Baxter, and P. Wilson: Metall. Mater. Trans. B 2005, vol. 36B, pp. 513–23.10.1007/s11663-005-0043-y ↗
22. M. Preuss, J.Q. Da Fonseca, I. Kyriakoglou, P.J. Withers, and G.J. Baxter: Superalloys-2004, TMS, Champion, 2004, pp. 477–84.10.7449/2004/Superalloys_2004_477_484 ↗
23. J.S. Tiley, D.W. Mahaffey, T. Alam, T. Rojhirunsakool, O. Senkov, T. Parthasarthy, and R. Banerjee: Mater. Sci. Eng. A, 2016, vol. 662, pp. 26–35.10.1016/j.msea.2016.03.030 ↗
24. C. Zener and J.H. Hollomom: J. Appl. Phys., 1944, vol. 15, pp. 22–32.10.1063/1.1707363 ↗
25. W. Harrison, M. Whittaker, and S. Williams: Materials, 2013, vol. 6, pp. 1118–37.10.3390/ma6031118 ↗
26. C. Carry and J.L. Strudel: Acta Metall., 1978, vol. 26, pp. 859–70.10.1016/0001-6160(78)90035-4 ↗