journal article·2009-11

Nominal vs Local Shot-Peening Effects on Fatigue Lifetime in Ti-6Al-2Sn-4Zr-6Mo at Elevated Temperature

S.K. Jha, R. John, J.M. Larsen

Publisher page

Abstract

A study is presented of elevated temperature (260 °C) fatigue lifetime variability in the shot-peened condition of the α + β titanium alloy, Ti-6Al-2Sn-4Zr-6Mo. It is shown that failures separate into two distributions: (1) governed by the nominal residual stress (RS) profile, promoting subsurface crack initiation and longer lifetimes; and (2) life-limiting behavior that is controlled by localized material-shot-peening interaction. In the residual-stress-free condition, failures occurred predominantly by surface crack initiation at the microstructural scale, on the order of 10 μm, by crystallographic facet formation in one or a few α particles or colonies. This mechanism was mitigated under the nominal shot-peening (SP) RS profile, producing failures initiating from the subsurface region by crystallographic faceting spread over a significantly larger area (equivalent diameter of about 100 to 200 μm) than in the absence of RS. Although the microstructure-scale surface-crack initiation was suppressed, the life-limiting failures under SP continued to occur by surface initiation, but through an apparently larger crack initiation size by formation of a flat, noncrystallographic fracture area (equivalent diameter of about 60 to 200 μm) at the crack origin.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Surface Treatment and Residual Stress · High-Velocity Impact and Material Behavior · Material Properties and Failure Mechanisms

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Shot Peening, L. Wagner, ed., Wiley-VCH, New York, NY, 2002.
2. A. Drechsler, T. Dorr, and L. Wagner: Mater. Sci. Eng., 1998, vol. A243, pp. 217–20.10.1016/S0921-5093(97)00804-6 ↗
3. J.D. Almer, J.B. Cohen, and B. Moran: Mater. Sci. Eng., 2000, vol. A284, pp. 268–79.10.1016/S0921-5093(99)00779-0 ↗
4. E.R. De Los Rios, A. Walley, M.T. Milan, and G. Hammersley: Int. J. Fatigue, 1995, vol. 17, pp. 493–99.10.1016/0142-1123(95)00044-T ↗
5. R.K. Nalla, I. Altenberger, U. Noster, G.Y. Liu, B. Scholtes, and R.O. Ritchie: Mater. Sci. Eng., 2003, vol. A355, pp. 216–30.10.1016/S0921-5093(03)00069-8 ↗
6. G.S. Was and R.M. Pelloux: Metall. Trans. A, 1979, vol. 10A, pp. 656–58.10.1007/BF02658332 ↗
7. M.A.S. Torres and H.J.C. Voorwald: Int. J. Fatigue, 2002, vol. 24, pp. 877–86.10.1016/S0142-1123(01)00205-5 ↗
8. J. Lindeman, C. Buque, and F. Appel: Acta Mater., 2006, vol. 54, pp. 1155–64.10.1016/j.actamat.2005.10.043 ↗
9. R. John, J.M. Larsen, D.J. Buchanan, and N.E. Ashbaugh: Incorporating Residual Stresses in Life Prediction of Turbine Disks, NATO RTO (AVT) Symp. on Monitoring and Management of Gas Turbine Fleets for Extended Life and Reduced Costs, Manchester, UK, Oct. 8–11, 2001.
10. M. Beghini, L. Bertini, and E. Vitale: Fatigue Fract. Eng. Mater. Struct., 1994, vol. 17, pp. 1433–44.10.1111/j.1460-2695.1994.tb00786.x ↗
11. C.H. Wang, S.A. Barter, and Q. Liu: J. Eng. Mater. Technol., 2003, vol. 125, pp. 183–90.10.1115/1.1493804 ↗
12. G.A. Webster and A.N. Ezeilo: Int. J. Fatigue, 2001, vol. 23, pp. S375-S383.10.1016/S0142-1123(01)00133-5 ↗
13. E. Hornbogen, M. Thumann, and C. Verpoort: Proc. 1st Int. Conf. on Shot Peening, ICSP 1, Pergamon Press, Oxford, United Kingdom, 1987, pp. 381–87.
14. A. Turnbull, E.R. De Los Rios, R.B. Tait, C. Laurant, and J.S. Boabaid: Fatigue Fract. Eng. Mater. Struct., 1998, vol. 21, pp. 1513–24.10.1046/j.1460-2695.1998.00125.x ↗
15. R.C. McClung: Fatigue Fract. Eng. Mater. Struct., 2007, vol. 30, pp. 173–205.10.1111/j.1460-2695.2007.01102.x ↗
16. Y. Mutoh, G.H. Fair, B. Noble, and R.B. Waterhouse: Fatigue Fract. Eng. Mater. Struct., 1987, vol. 10, pp. 261–72.10.1111/j.1460-2695.1987.tb00205.x ↗
17. E.R. De Los Rios, M. Trull, and A. Levers: Fatigue Fract. Eng. Mater. Struct., 2000, vol. 23, pp. 709–16.10.1046/j.1460-2695.2000.00287.x ↗
18. C.A. Rodopoulous, S.A. Curtis, E.R. LosRios, and J. Solisromero: Int. J. Fatigue, 2004, vol. 26, pp. 849–56.10.1016/j.ijfatigue.2004.01.003 ↗
19. Z.L. Lu, S.X. Li, Y.Y. Lui, Q.Y. Zhang, J.F. Lei, and Z.X. Mu: Mater. Sci. Eng., 2004, vol. A383, pp. 283–88.
20. M.C. Berger and J.K. Gregory: Mater. Sci. Eng., 1999, vol. A263, pp. 200–04.10.1016/S0921-5093(98)01165-4 ↗
21. W.Z. Zhuang and G.R. Halford: Int. J. Fatigue, 2001, vol. 23, pp. S31-S37.10.1016/S0142-1123(01)00132-3 ↗
22. B.L. Boyce, X. Chen, J.O. Peters, J.W. Hutchinson, and R.O. Ritchie: Mater. Sci. Eng., 2003, vol. A349, pp. 48–58.10.1016/S0921-5093(02)00543-9 ↗
23. D.J. Buchanan and R. John: Scripta Mater., 2008, vol. 59, pp. 286–89.10.1016/j.scriptamat.2008.03.021 ↗
24. R. John, D.J. Buchanan, S.K. Jha, and J.M. Larsen: Scripta Mater., 2009, vol. 61, pp. 343–46.10.1016/j.scriptamat.2009.03.038 ↗
25. S. Curtis, E.R. de Los Rios, C.A. Rodopoulos, and A. Levers: Int. J. Fatigue, 2003, vol. 25, pp. 59–66.10.1016/S0142-1123(02)00049-X ↗
26. G.R. Leverant, B.S. Langer, A. Yuen, and S.W. Hopkins: Metall. Trans. A, 1979, vol. 10A, pp. 251–57.10.1007/BF02817635 ↗
27. S.K. Jha, M.J. Caton, and J.M. Larsen: Mater. Sci. Eng. A, 2007, vol. A468-470, pp. 23–32.10.1016/j.msea.2006.10.171 ↗
28. S.K. Jha, M.J. Caton, and J.M. Larsen: in Superalloys-2008, R.C. Reed, K.A. Green, P. Caron, T.P. Gabb, M.G. Fahrmann, E.S. Huron, and S.A. Woodard, eds., TMS, Warrendale, PA, 2008, pp. 565–72.
29. S.K. Jha and J.M. Larsen: VHCF-4, Proc. 4th Int. Conf. on Very High Cycle Fatigue, Ann Arbor, MI, 2007, J.W. Jones, J.E. Allison, J.M. Larsen, and R.O. Ritchie, eds., TMS Publications, 2007, pp. 385–96.
30. S.K. Jha, J.M. Larsen, and A.H. Rosenberger: Eng. Fract. Mech., 2009, vol. 76, pp. 681–94.10.1016/j.engfracmech.2008.10.013 ↗
31. C.J. Szczepanski, S.K. Jha, J.M. Larsen, and J.W. Jones: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2841–51.10.1007/s11661-008-9633-z ↗
32. P.S. Prevey: in Developments in Materials Characterization Technologies, C. Vander Voort and J. Friel, eds., ASM INTERNATIONAL, Materials Park, OH, 1996, pp. 103–10.
33. S.K. Jha, J.M. Larsen, A.H. Rosenberger, and G.A. Hartman: Scripta Mater., 2003, vol. 48, pp. 1637–42.10.1016/S1359-6462(03)00132-5 ↗
34. L. Wagner and G. Lutjering: Proc. ICSP-2, Chicago, IL, May 14–17, 1984, American Shot Peening Society, NJ, pp. 194–200.
35. J.T. Cammett, P.S. Prevey, and N. Jayaraman: Proc. ICSP-9, Paris, France, September 6–9, 2005, American Shot Peening Society, NJ.