Microstructure, Mechanical Properties, and Toughening Mechanisms of a New Hot Stamping-Bake Toughening Steel
Source abstract
Abstract
In this article, the hot stamping-bake toughening process has been proposed following the well-known concept of bake hardening. The influences of the bake time on the microstructure and the mechanical properties of the hot stamped-baked part were studied by means of scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and mechanical tests at room temperature. The results show that the amount of the retained austenite was nearly not changed by the bake process. Also observed were spherical Cu-rich precipitates of about 15 nm in martensite laths. According to the Orowan mechanism, their contribution of the Cu-rich precipitates to the strength is approximately 245 MPa. With the increase of the bake time, the tensile strength of the part was decreased, whereas both the ductility and the product of the tensile strength and ductility were increased then decreased. The tensile strength and ductility product and the tensile strength are as high as 21.9 GPa pct, 2086 MPa, respectively. The excellent combined properties are due to the transformation-induced plasticity effect caused by retained austenite.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. H. Karbasian and A.E. Tekkaya: J. Mater. Process. Tech., 2010, vol. 210, no. 5, pp. 2103-18.10.1016/j.jmatprotec.2010.07.019 ↗
2. M. Naderi: Ph.D. Thesis, RWTH Aachen, Aachen, 2007
3. A. Mittal: Catalogue—European Edition, 2014.
4. J.G. Speer, D.K. Matlock, B.C. De Cooman, and J.G. Schroth: Acta Mater., 2003, vol. 51, pp. 2611-22.10.1016/S1359-6454(03)00059-4 ↗
5. J.G. Speer, D.V. Edmonds, F.C. Rizzo, and D.K. Matlock: Curr. Opin. Solid State Mater., 2004, vol. 8, no. 3, pp. 219-3710.1016/j.cossms.2004.09.003 ↗
6. S. Matas and R.F. Hehemann: Nature, 1960, vol. 187, pp. 685.10.1038/187685a0 ↗
7. T.Y. Hsu and X.M. Li: Acta Metall. Sin., 1983, vol. 19, no. 6, pp. A505–10.
8. A.J. Clarke, J.G. Speer, M.K. Miller, R.E. Hackenberg, D.V. Edmonds, D.K. Matlock, F.C. Rizzo, K.D. Clarke, and E. De Moor: Acta Mater., 2008, vol. 56, no. 1, pp. 16-22.10.1016/j.actamat.2007.08.051 ↗
9. E. De Moor, S. Lacroix, A.J. Clarke, J. Penning, and J.G. Speer: Metall. Mater. Trans. A, 2008, vol. 39, pp. 2586-95.10.1007/s11661-008-9609-z ↗
10. F. Tariq and R.A. Baloch: J. Mater. Eng. Perform., 2013, vol. 2, pp. 1-14.10.1142/9781908977137_0001 ↗
11. E. ParaviciniBagliani, M.J. Santofimia, L. Zhao, J. Sietsma, and E. Anelli: Mater. Sci. Eng. A, 2013, vol. 559, pp. 486–95.10.1016/j.msea.2012.08.130 ↗
12. S. Yan, X.H Liu, W.J. Liu, H.F. Lan, and H.Y. Wu: Acta Metall. Sin., 2013, vol. 49, no. 8, pp. 917-24.10.3724/SP.J.1037.2013.00176 ↗
13. H.P. Liu, X.W. Lu, X.J. Jin, H. Dong, and J. Shi: Scripta Mater., 2011, vol. 64, no. 8, pp. 749-52.10.1016/j.scriptamat.2010.12.037 ↗
14. X.D. Wang, N. Zhong, L. Wang, Y.H. Rong, and T.Y. Hsu: J. Mater. Res., 2009, vol. 24, pp. 260-7.10.1557/JMR.2009.0029 ↗
15. T. Tsuchiyama, J. Tobata, T. Tao, N. Nakada, and S. Takaki: Mater. Sci. Eng. A, 2012, vol. 532, pp. 585-92.10.1016/j.msea.2011.10.125 ↗
16. N. Zhong, X.D. Wang, L. Wang, and Y.H. Rong: Mater. Sci. Eng. A, 2009, vol. 506, pp. 111-6.10.1016/j.msea.2008.11.014 ↗
17. M.J. Santofimia, L. Zhao, R. Petrov, and J. Sietsma: Mater. Charact., 2008, vol. 59, no. 12, pp. 1758-64.10.1016/j.matchar.2008.04.004 ↗
18. T.Y. Hsu and X.M. Li: Acta Metall. Sin., 1983, vol. 19, no. 2, pp. A83-8.
19. J.G. Speer, E. De Moor, K.O. Findley, D.K. Matlock, B.C. De Cooman, and D.V. Edmonds: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 3591-601.10.1007/s11661-011-0869-7 ↗
20. E.V. Pereloma, I.B. Timokhina, and P.D. Hodgson: Mater. Sci. Eng. A, 1999, vol. 273, pp. 448-52.10.1016/S0921-5093(99)00325-1 ↗
21. G.A. Thomas, J.G. Speer, and D.K. Matlock: Metall. Mater. Trans. A, 2011, vol. 42, pp. 3652-9.10.1007/s11661-011-0648-5 ↗
22. T.Y. Hus: Heat Treat., 2010, vol. 25, no. 4, pp. 1-5.
23. H.P. Liu, X.J. Jin, H. Dong, and J. Shi: Mater. Charact., 2011, vol. 62, pp. 223-7.10.1016/j.matchar.2010.12.003 ↗
24. H.Y. Li, X.W. Lu, W.J. Li, and X.J. Jin: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1284-300.10.1007/s11661-010-0184-8 ↗
25. R. Wang, J. Zhou, W.Z. Li, and L. Huang: Phys. Exam. Test., 2008, vol. 26, no. 4, pp. 46-8.
26. N.H. Van Dijk, A.M. Butt, L. Zhao, J. Sietsma, S.E. Offerman, J.P. Wright, S. van der Zwaag: Acta Mater., vol. 53(20), pp. 5439–47.10.1016/j.actamat.2005.08.017 ↗
27. N. Zhong, X.D. Wang, Y.H. Rong, and L. Wang: J. Mater. Sci. Tech., 2006, vol. 22, no. 6, pp. 751-4.
28. Y. Okamura, M. Okushima, H. Tamehiro, T. Kasuya, M. Tanaka, R. Yamaba, H. Inoue, and A. Seto: Nippon Steel Technol. Rep., 1995, vol. 66, pp. 65–76
29. W.J. Liu: Acta Metall. Sin., 2014, vol. 27, no. 3, pp. 373-82.10.1007/s40195-014-0076-9 ↗
30. A.C. Damask and G.J. Dienes: Point Defects in Metals, 1st ed., Gordon and Breach, New York, NY, 1963.
31. A. Kokosza and J. Pacyna: Arch. Mater. Sci. Eng., 2008, vol. 31, pp. 87.
32. Q.X. Dai, A.D. Wang, and X.N. Cheng: J. Iron. Steel. Res. Int., 2002, vol. 14, no. 6, pp. 50-3.
33. Q.L. Yong: Second Phase in Structural Steels, 1st ed., Metallurgical Industry Press, Beijing, China, 2006, p. 42.
34. N.J. Olson: Ph.D. Dissertation, Iowa State University, Ames, IA, 1970.
35. X.N. Cheng and Q.X. Dai: Material Solid State Transformation and Diffusion, 1st ed., Chemical Industry Press, Beijing, China, 2006, p. 30.