Texture and residual strain in two SiC/Ti-6-2-4-2 titanium composites
Source abstract
Abstract
Residual strain and texture variations were measured in two titanium matrix composites reinforced with silicon carbide fibers (Ti/SiC) of similar composition but fabricated by different processing routes. Each composite comprised a Ti-6242 α/β matrix alloy containing vol 35 pct continuous SiC fibers. In one, the matrix was produced by a plasma sprayed (PS) route, and in the other by a wiredrawn (WD) process. The PS and WD composites were reinforced with SCS-6 (SiC) and Trimarc (SiC) fibers, respectively. The texture in the titanium matrices differed significantly. The titanium matrix for the PS material exhibited random texture pre and post fabrication of the composite. For the WD material, the starting texture of the monolithic titanium matrix was ≈17 times random, but after consolidation into composite form, it was ≈6 times random. No significant differences were noted in the fiber-induced matrix residual strains between the composites prepared by the two procedures. However, the Trimarc (WD) fibers recorded higher (≈1.3 times) compressive strains than the SCS-6 (PS) fibers. Stresses and stress balance results are reported. Plane-specific elastic moduli, measured in load tests on the unreinforced matrices, showed little difference.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. J.M. Larsen, K.A. Williams, S.J. Balsone, and M.A. Stucke: in High Temperature Aluminides and Intermetallics, S.H. Whang, C.T. Liu, D.P. Pope, and J.O. Stiegles, eds., TMS/ASM INTERNATIONAL, 1990, pp. 521–56.
2. J.M. Larsen, W.C. Revelos, and M.L. Gambone: 1998 Intermetallic Composites IL, Materials Research Society Symposia Proceedings, D.B. Miracle, D.L. Anton, and J.A. Graves, eds., Materials Research Society, Pittsburgh, PA, 1992 vol. 273, pp. 3–16.
3. P.K. Wright, M.D. Sensmeier, and M.L. Gambone: in Residual Stresses in Composites: Measurement, Modeling and Effect on Thermo-Mechanical Properties, E.V. Barrera, I. Dutta, and S.G. Fishman, eds., TMS, Warrendale, PA, 1993, pp. 207–18.
4. M. Peters, A. Gysler, and G. Lutjering: Metall. Trans. A, 1984, vol. 15A, pp. 1597–1605.10.1007/BF02657799 ↗
5. W.S. Johnson, S.J. Lubowinski, and A.L. Highsmith: in ASTM STP 1080, J.M. Kennedy, H.H. Moeller, and W.S. Johnson, eds. Philadelphia, PA, 1990, pp. 193–218.
6. H. Gigernzer and P.K. Wright: in Titanium Aluminide Composites, WL-TR-91-4020, P.R. Smith, S.J. Balsone, and T. Nicolas, eds., 1989, pp. 251–64.
7. C.A. Bigelow, W.S. Johnson, and A.R. Naik: in Mechanics of Composite Materials and Structures, J.N. Reddy and J.L. Telpy, eds., 1989.
8. M.R. James: in Int. Conf. on Residual Stresses II, G. Beck, S. Denis, and A. Simon, eds., Elsevier, New York, NY, 1989, pp. 429–35.10.1007/978-94-009-1143-7_72 ↗
9. P. Rangaswamy, W.C. Revelos, and N. Jayaraman: J. Composites Technol. Res., (JCTRER), 1994, vol. 16 (1), pp. 47–53.10.1520/CTR10394J ↗
10. P. Rangaswamy and N. Jayaraman: J. Composites Technol. Res., (JCTRER), 1995, vol. 17 (1), pp. 43–49.10.1520/CTR10512J ↗
11. B.N. Cox, M.R. James, D.B. Marshall, and R.C. Addison, Jr.: Metall. Trans. A, 1990, vol. 21A, pp. 2701–07.10.1007/BF02646065 ↗
12. M.R. James: in Residual Stresses—3, H. Fujiwara, T. Abe, and K. Tanaka, eds., Elsevier, New York, NY, 1992, pp. 555–60.
13. M.R. James, M.A. Bourke, J.A. Goldstone, and A.C. Lawson: Adv. X-ray Analysis, 1993, vol. 36.10.1154/S0376030800019108 ↗
14. Paul S. Prevey: Adv. X-ray Analysis, 1988, vol. 20, pp. 345–54.
15. A.D. Krawitz: Residual Stresses in Composites, Measurement, Modeling & Effects on Thermo-Mechanical Behavior, E.V. Barrera and I. Dutta, eds., TMS, Warrendale, PA, 1993, pp. 161–76.
16. P. Rangaswamy, M.A.M. Bourke, P.K. Wright, E. Kartzmark, J. Roberts, and N. Jayaraman: Mater. Sci. Eng., 1997, vol. A224, pp. 200–09.10.1016/S0921-5093(96)10517-7 ↗
17. A. Saigal, D.S. Kupperman, and S. Majumdar: Mater. Sci. Eng., 1992, vol. AI50, pp. 59–66.10.1016/0921-5093(90)90008-Q ↗
18. S. Majumdar, J.P. Singh, D. Kupperman, and A.D. Krawitz: J. Eng. Mater. Technol., 1991, vol. 113, pp. 51–59.10.1115/1.2903382 ↗
19. D.S. Kupperman, S. Majumdar, and J.P. Singh: Neutron News, 1991, vol. 2, pp. 15–18.10.1080/10448639108218733 ↗
20. R.B. Von Dreele: J. Appl. Crystal, 1997, vol. 30, pp. 517–25.10.1107/S0021889897005918 ↗
21. R.B. Von Dreele, J.D. Jorgensen, and C.G. Windsor: J. Appl. Crystal, 1982, vol. 15, pp. 581–89.10.1107/S0021889882012722 ↗
22. A.C. Larson and R.B. Von Dreele: “GSAS—Generalized Structural Analysis System,” Report No. LAUR 86-748, Los Alamos National Laboratory, Los Alamos, NM, 1994.
23. C. Jones, C.J. Kiely, and S.S. Wang: J. Mater. Res., 1989, vol. 4 (2), pp. 327–35.10.1557/JMR.1989.0327 ↗
24. K. Stevens and J. Larsen: Materials Directorate, Wright Patterson Airforce Base, Dayton, OH, unpublished research, 1998.
25. M.R. Daymond: ISIS, Rutherford Appleton Lab., Didcot, United Kingdom, private communication, 1999.
26. M.A.M. Bourke, J.A. Goldstone, N. Shi, J.E. Allison, M.G. Stout, and A.C. Lawson: Scripta Metall. Met., 1993, vol. 129, pp. 771–76.10.1016/0956-716X(93)90224-G ↗
27. R.W. Hertzberg: Deformation and Fracture Mechanics of Engineering Materials, Wiley, New York, NY, 1996, vol. 14.
28. M.A. Przystupa, A.K. Vasudevan, and A.D. Rollett: Mater. Sci. Eng., 1994, vol. A186, pp. 35–44.10.1016/0921-5093(94)90303-4 ↗
29. J.R. Hirsch: Mater. Sci. Technol., 1990, vol. 6, p. 1048.10.1179/mst.1990.6.11.1048 ↗
30. F.J. Humphreys and P.N. Kalu: Acta Metall., 1990, vol. 38, p. 918.10.1016/0956-7151(90)90164-C ↗
31. Y.I. Liu, N. Hansen, and D. Juul Jensen: Proc. 12th Int. Ris Symp. on Materials Science, 1991. p. 67.
32. A. Poudens, T. Bretheau, and B. Bacroix: Proc. 12th Int. Ris Symp. on Materials Science, 1991, p. 417.
33. K. Lucke and O. Engler: Mater. Sci. Technol., 1990, vol. 6, p. 1113.10.1179/mst.1990.6.11.1113 ↗
34. S. Nourkbakhsh and T.D. O’Brien: Mater. Sci. Technol., 1988, vol. 100, pp. 109–14.
35. B.S. Majumdar: New Mexico Tech, Socorro, NM, private communication, 1999.
36. S.G. Warrier and B.S. Majumdar: Mater. Sci. Eng. A-Struct. Mater. Prop. Microstr. Processing, 1997, vol. 237 (2), pp. 256–67.10.1016/S0921-5093(97)00423-1 ↗
37. H. Choo, P. Rangaswamy, and M.A.M. Bourke: Scripta Metall., vol. 42, pp. 175–81, 2000.10.1016/S1359-6462(99)00334-6 ↗
38. P.J. Withers and A.P. Clarke: Acta Metall., 1998, vol. 46 (18), pp. 6585–98.
39. M.R. Daymond, M.A.M. Bourke, R.J. Von Dreele, B. Clausen, and T. Lorentzen: J. Appl. Phys., 1997, vol. 92, p. 1554.10.1063/1.365956 ↗
40. M.R. Daymond, M.A.M. Bourke, and R.J. Von Dreele: J. Appl. Phys., 1999, vol. 85, p. 739.10.1063/1.369154 ↗
41. A.D. Krawitz, R.A. Winholtz, and C.M. Weisbrook: Mater. Sci. Eng., 1996, vol. A206, p. 176.10.1016/0921-5093(95)10018-0 ↗
42. H. Choo, M.A.M. Bourke, P. Nash, M.A. Daymond, and N. Shi: Mater. Sci. Eng., 1999, vol. A264, p. 108.10.1016/S0921-5107(99)00330-X ↗