journal article·2012-02Open access

Time-Dependent Fatigue Crack Propagation Behavior of Two Solid-Solution-Strengthened Ni-Based Superalloys—INCONEL 617 and HAYNES 230

Longzhou Ma, Shawoon K. Roy, Muhammad H. Hasan, Joydeep Pal, Sudin Chatterjee

Abstract

The fatigue crack propagation (FCP) as well as the sustained loading crack growth (SLCG) behavior of two solid-solution-strengthened Ni-based superalloys, INCONEL 617 (Special Metals Corporation Family of Companies) and HAYNES 230 (Haynes International, Inc., Kokomo, IN), were studied at increased temperatures in laboratory air under a constant stress-intensity-factor (K) condition. The crack propagation tests were conducted using a baseline cyclic triangular waveform with a frequency of \( \frac{1}{3} \) Hz. Various hold times were imposed at the maximum load of a fatigue cycle to study the hold time effect. The results show that a linear elastic fracture mechanics (LEFM) parameter, stress intensity factor (K), is sufficient to describe the FCP and SLCG behavior at the testing temperatures ranging from 873 K to 1073 K (600 °C to 800 °C). As observed in the precipitation-strengthened superalloys, both INCONEL 617 and HAYNES 230 exhibited the time-dependent FCP, steady SLCG behavior, and existence of a damage zone ahead of crack tip. A thermodynamic equation was adapted to correlate the SLCG rates to determine thermal activation energy. The fracture modes associated with crack propagation behavior were discussed, and the mechanism of time-dependent FCP as well as SLCG was identified. Compared with INCONEL 617, the lower crack propagation rates of HAYNES 230 under the time-dependent condition were ascribed to the different fracture mode and the presence of numerous W-rich M6C-type and Cr-rich M23C6-type carbides. Toward the end, a phenomenological model was employed to correlate the FCP rates at cycle/time-dependent FCP domain. All the results suggest that an environmental factor, the stress assisted grain boundary oxygen embrittlement (SAGBOE) mechanism, is mainly responsible for the accelerated time-dependent FCP rates of INCONEL 617 and HAYNES 230.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. W.R. Corwin: Nucl. Eng. Tech., 2006, vol. 38, pp. 591–618.
2. R. Wright, J. Simpson, A. Wertsching, and W.D. Swank: Proc. 4th International Topical Meeting on High Temperature Reactor Technology HTR 2008, Washington, DC, 2008, pp. 1–5.
3. R.N. Wright: Report No. INL/EXT-06-11494, Idaho National Laboratory, 2006.
4. T.C. Totemeier and H. Tian: Mater. Sci. Eng. A, 2007, vols. 469–470A, pp. 81–87.10.1016/j.msea.2006.10.170 ↗
5. L.-Z. Ma, K.-M. Chang, S.K. Mannan, and S.J. Patel: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3465–77.10.1007/s11661-002-0334-8 ↗
6. K.-M. Chang, M.F. Henry, and M.G. Benz: JOM, 1990, pp. 29–35.10.1007/BF03220467 ↗
7. K.-M. Chang: Report No. 91CRD 066, GE Research & Development Center, 1991.
8. A. Saxsena: Fatig. Eng. Mater. Struct., 1980, vol. 3, pp. 247–55.10.1111/j.1460-2695.1980.tb01364.x ↗
9. V. Dimopulos, K.M. Nikibin, and G.A. Webster: Metall. Trans. A, 1988, vol. 19A, pp. 873–80.10.1007/BF02628370 ↗
10. R. Mollins, G. Hochstetter, J.C. Chassaigne, and E.E Anderieu: Acta Mater., 1997, vol. 45, pp. 663–74.anu K,10.1016/S1359-6454(96)00192-9 ↗
11. S. Floreen: Metall. Trans. A, 1975, vol. 6A, pp. 1741–49.10.1007/BF02642302 ↗
12. S. Floreen and R.H. Kane: Metall. Trans. A, 1979, vol. 10A, pp. 1745–51.10.1007/BF02811710 ↗
13. K. Sadananda and P. Shahinian: Metall. Trans. A, 1977, vol. 8A, pp. 439–49.10.1007/BF02661754 ↗
14. W.J. Ren: Press. Vessel Tech., 2009, vol. 31, pp. 044002/1–15.
15. Special Metals Corporation: Inconel Alloy 617, Publication No. SMC-029, 2005.
16. Haynes International Inc.: HAYNES 230 Alloy, High Temperature Alloys Brochure, Publication No.: H-3024E, 2009.
17. J.K. Benz, J.H. Kim, and R.G. Ballinger: J. Eng. Gas. Turbines & Power, 2010, vol. 132, pp. 102901/1–7.10.1115/1.3155793 ↗
18. S.-S. Hsu: J. Nucl. Sci. Technol., 1993, vol. 30, no. 4, pp. 302–13.10.3327/jnst.30.302 ↗
19. K. Bhanu, S. Rao, H. Schiffers, H. Schuster, and H. Nickel: Metall. Trans. A, 1988, vol. 19A, pp. 360–71.
20. Y.L. Lu, P.K. Liaw, Y. Sun, G.Y. Wang, S.A. Thompson, J.W. Blust, P.F. Browning, A.K. Bhattacharya, J.M. Aurrecoechea, and D.L. Klarstrom: Acta Mater., 2007, vol. 55, pp. 767–75.10.1016/j.actamat.2006.06.044 ↗
21. A.K. Roy, S. Chatterjee, M.H. Hasan, J. Pal, and L.-Z. Ma: Mater. Sci. Eng. A, 2010, vol. 527, pp. 4830–36.10.1016/j.msea.2010.04.005 ↗
22. X.Y. Lee, Y.L. Lu, P.K. Liaw, H. Choo, S.A. Thompson, J.W. Blust, P.F. Browing, A.K. Bhattacharya, J.M. Aurrecoechea, and D.L. Klarstrom: Mech. Time-Depend. Mater., 2008, vol. 12, pp. 31–44.10.1007/s11043-008-9049-6 ↗
23. H.H. Johnson: Mater. Res. Stand., 1965, vol. 5, pp. 442–45.
24. H. Tata, P. Paris, and G. Irwin: The Stress Analysis of Crack Handbook, Del Research Corporation, St. Louis, MO, 1985.
25. T.S. Jo, J.H. Lim, and Y.D. Kim: J. Nucl. Mater., 2010, vol. 406, pp. 360–64.10.1016/j.jnucmat.2010.09.027 ↗
26. W.L. Mankins, J.C. Hosier, and T.H. Bassford: Metall. Trans., 1974, vol. 5, pp. 2579–90.10.1007/BF02643879 ↗
27. H.M. Tawancy: J. Mater. Sci., 1992, vol. 27, pp. 6481–89.10.1007/BF00576301 ↗
28. Y.L. Lu, P.K. Liaw, G. Yang, M.L. Benson, S.A. Thompson, J.W. Blust, P.F. Browning, A.K. Bhattacharya, J.M. Aurrecoechea, and D.L. Klarstrom: Mater. Sci. Eng. A, 2005, vol. A397, pp. 122–31.10.1016/j.msea.2005.01.048 ↗
29. L.-Z. Ma and K.-M. Chang: Scripta Mater., 2003, vol. 48, pp. 1271–76.10.1016/S1359-6462(03)00049-6 ↗
30. H.M. Tawancy: Oxid. Met., 1996, vol. 45, nos. 3 and 4, pp. 323–48.10.1007/BF01046988 ↗
31. H. Ghonem and D. Zheng: Mater. Sci. Eng. A, 1992, vol. 150, pp. 151–60.10.1016/0921-5093(92)90107-C ↗
32. D.D. Krueger, S.D. Antolovich, and R.H. Van Stone: Metall. Trans. A, 1987, vol. 18A, pp. 1431–48.10.1007/BF02646657 ↗
33. L.A. Games: Superalloy 718: Metallurgy and Applications, Ed. E.A. Loria, TMS, Warrendale, PA, 1989, pp. 499–515.10.7449/1989/Superalloys_1989_499_515 ↗