journal article·2015-04

Prediction and Confirmation of Phases Formed in the Diffusion Zone of Ti-5Ta-2Nb/304L SS Explosive Clads

T. N. Prasanthi, Cheruvathur Sudha, P. K. Parida, A. Dasgupta, S. Saroja

Publisher page

Abstract

Explosive cladding, a solid-state welding technique was used to fabricate dissimilar joints between Ti-5Ta-2Nb alloy and 304L austenitic stainless steel. To remove the residual stresses and improve the ductility of the ‘as clad’ joints, further heat treatments were carried out in the temperature range of 873 K to 1073 K (600 °C to 800 °C) for varying durations. Systematic change in the interface microstructure and microchemistry due to thermally activated interdiffusion of alloying elements was studied. This information together with that of the thermal stability of non-equilibrium phases in base materials was used to evaluate the probability of formation of various phases across the explosive clad interface using JMatPro®, a materials modeling software. In the clad heat treated at 1073 K (800 °C) for 20 hours, evidence was obtained for the presence of different phases (predicted to form) in the diffusion zone by transmission electron microscopy on site-specific specimens prepared by focused ion beam milling. An attempt to understand the specific influence of the type of phase, their relative mole fraction, and microchemistry on the mechanical property of the joint has also been made based on both experimental and computational study.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. B. Raj and U. Kamachi Mudali: Prog. Nucl. Energy, 2006, vol. 48, pp. 283–313.10.1016/j.pnucene.2005.07.001 ↗
2. U. KamachiMudali, A. Ravishankar, S. Ningshen, S. Girija, S. Ravikumar, and K. Thyagarajan: Energy Proc., 2011, vol. 7, pp. 468–73.10.1016/j.egypro.2011.06.064 ↗
3. U. KamachiMudali, B.M. AnandaRao, K. Shanmugum, R. Natarajan, and B. Raj: J. Nucl. Mater., 2003, vol. 321, pp. 40–48.10.1016/S0022-3115(03)00194-6 ↗
4. M.F. Wu, C. Yu, Z.S. Yu and R.F. Li: Mater. Sci. Technol., 2004, vol. 20, pp. 658-660.10.1179/026708304225012080 ↗
5. S. Kundu, M. Ghosh and S. Chatterjee: Mater. Sci. Engg. A., 2006, vol. 428, pp. 18-23.10.1016/j.msea.2005.10.047 ↗
6. M. Ghosh, K. Bhanumurthy, G.B. Kale, J. Krishnan and S. Chatterjee: J. Nucl. Mater., 2003, vol. 322, pp. 235-241.10.1016/j.jnucmat.2003.07.004 ↗
7. M. Ghosh and S. Chatterjee: Mater. Sci. Engg. A, 2003, vol. 358, pp. 152-158.10.1016/S0921-5093(03)00298-3 ↗
8. X. Yue, P. He, J.C. Feng, J.H. Zhang and F.Q. Zhu: Mater. Chara., 2008, vol. 59, pp. 1721-1727.10.1016/j.matchar.2008.03.014 ↗
9. T. Wang, B. Zhang, G. Chen, J.-C. Feng and Q. Tang: Trans. Nonferrous Met. Soc. China, 2010, vol. 20, pp. 1829–34.10.1016/S1003-6326(09)60381-2 ↗
10. F. Findik: Mater. Des., 2011, vol. 32, pp. 1081-1093.10.1016/j.matdes.2010.10.017 ↗
11. A. Pocalyko: Mater. Prot. 1965, vol. 4(6), pp. 10-15.
12. C.H. Oxford and P.E.J. Flewitt: Metall. Trans. A, 1977, vol. 8, pp. 741-750.10.1007/BF02664784 ↗
13. Å. Öberg, N. Mårtensson and J.-Å. Schweitz: Metall. Trans. A, 1985, vol. 16A, pp. 841–52.10.1007/BF02814835 ↗
14. R.A. Patterson: Fundamental of exploisve welding, ASM Handbook, vol. 6, ASM International, USA, 1993, pp. 528-533.
15. G. Arthur: Mater Des., 1985, vol. 6, pp. 37-41.10.1016/0261-3069(85)90089-5 ↗
16. C. Merriman: Weld. J., 2006, vol. 85, pp. 27–29.
17. R.V. Tamhankar and J. Ramesam: Mater. Sci. Eng., 1974, vol. 13, pp. 245–54.10.1016/0025-5416(74)90195-5 ↗
18. G.R. Cowan, O.R. Bergman and A.H. Holtzman: Metall. Trans., 1971, vol. 2, pp. 3145-3155.10.1007/BF02814967 ↗
19. B. Crossland and J.D. Willimas: Met. Rev., 1970, vol. 15, pp. 79-100.10.1179/imr.1970.15.1.79 ↗
20. S.A.A. AkbariMousavi, L.M. Barrett, and S.T.S. AlHassani: J. Mater. Proc. Tech., 2008, vol. 202, pp. 224–39.10.1016/j.jmatprotec.2007.09.028 ↗
21. M. Acarer and B. Demir: Mater. Lett., 2008, vol. 62, pp. 4158-4160.10.1016/j.matlet.2008.05.060 ↗
22. B. Gulenc: Mater. Des., 2008, vol. 29, pp. 275-278.10.1016/j.matdes.2006.11.001 ↗
23. A. Durgutlu, B. Gulenc and F. Findik: Mater. Des., 2005, vol. 26, pp. 497-507.10.1016/j.matdes.2004.07.021 ↗
24. N. Kahraman and B. Gulenc: J Mater. Proc. Tech., 2005, vol. 169, pp. 67-71.10.1016/j.jmatprotec.2005.02.264 ↗
25. M. Nishida, A. Chiba, K. Imamura, H. Minato and J. Shudo: Metall. Trans. A, 1993, vol. 24, 735-742.10.1007/BF02656641 ↗
26. D. Jaramillo, V.A. Szecket and O.T. Inal, Mater. Sci. Engg., 1987, vol. 91, pp. 217-222.10.1016/0025-5416(87)90300-4 ↗
27. S.A.A. Akbari Mousavi and P. Farhadi Sartangi: Mater. Des., 2009, vol. 30, pp. 459-468.10.1016/j.matdes.2008.06.016 ↗
28. J. Song, A. Kostka, M. Veehmayer and D. Raabe: Mater. Sci. Engg. A, 2011, vol. 528, pp. 2641-2647.10.1016/j.msea.2010.11.092 ↗
29. S.A.A. AkbariMousavi and P. FarhadiSartangi: Mater. Sci. Eng. A, 2008, vol. 494, pp. 329–36.10.1016/j.msea.2008.04.032 ↗
30. X. Changqing and J. Zhanpeng: J Less Comm. Metals, 1990, vol. 162, pp. 315-322.10.1016/0022-5088(90)90347-M ↗
31. F. Findik, R. Yilmaz, and T. Somyurek: Sci. Res. Essays, 2011, vol. 6(19), pp. 4141–51.10.5897/SRE11.1018 ↗
32. C. Sudha, T.N. Prasanthi, S. Murugesan, S. Saroja, P. Kuppusami and M. Vijayalakshmi: Sci. Technol. Weld. Join., 2011, vol. 16(2), pp. 133-139.10.1179/1362171810Y.0000000001 ↗
33. C. Sudha, T.N. Prasanthi, V. Thomas Paul, S. Saroja and M. Vijayalaksmi: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 3596-3607.10.1007/s11661-012-1198-1 ↗
34. T.N. Prasanthi, C. Sudha, H. Khalid Rafi, S. Saroja, and M. Vijayalakshmi: Proc. National Welding Seminar, 21–23 December 2010, Vizag, India, IIW/Vizag/NWS-2010/Tech/ID/3/H/7821.
35. C. Sudha, T.N. Prasanthi, V. Thomas Paul, S. Saroja, and M. Vijayalakshmi: Procedia Eng., 2014, vol. 86, pp.42–50.10.1016/j.proeng.2014.11.009 ↗
36. T.N. Prasanthi, C. Sudha, S. Murugesan, and S. Saroja: Unpublished research, 2014.
37. Z. Guo, N. Saunders, J.P. Schillé and A.P. Miodownik: Mater. Sci. Technol. A, 2009, vol. 499, pp. 7-13.10.1016/j.msea.2007.09.097 ↗
38. B. Alemán, I. Gutiérrez and J.J. Urcola: Mater. Sci. Technol., 1993, vol. 9, pp. 633-641.10.1179/mst.1993.9.8.633 ↗
39. Y. Liu, L. Zhang, Y. Du and D. Liang: Calphad, 2009, vol. 33, pp. 732-736.10.1016/j.calphad.2009.09.007 ↗
40. H. Nakajima, K. Yusa and Y. Kondo: Scripta Mater., 1996, vol. 34(2), pp. 249-253.10.1016/1359-6462(95)00511-0 ↗
41. T.B. Massalski, ed.: Binary Phase Diagrams, 1992, vol 2, pp. 1347, 1785, vol. 3, p. 2875, ASM, Metals Park, OH.
42. I. Weiss and S.L. Semiatin: Mater. Sci. Engg. A, 1998, vol. 243, pp. 46-65.10.1016/S0921-5093(97)00783-1 ↗
43. H.C. Chen and G.H. Cheng: J Mater. Sci., 1989, vol. 24, pp. 1991-1994.10.1007/BF02385411 ↗
44. J.F. Shackelford and W. Alexander: Mechanical Properties of Materials, Materials Science and Engineering Handbook, CRC Press LLC, Boca Raton, USA, 2001, pp. 56.
45. W. Gasior and A. Debski: Archives of Metall. Mater., 2012, vol. 57(4), pp. 1095-1104.10.2478/v10172-012-0122-4 ↗
46. L. Pandelaers, B. Blanpain and P. Wollants: Calphad, 2011, vol. 35, pp. 518-522.10.1016/j.calphad.2011.09.001 ↗
47. H. Nakajima and M. Koiwa: ISIJ Inter., 1991, vol. 31(8), pp. 757-766.10.2355/isijinternational.31.757 ↗
48. V. Raghavan: Phase Diagrams of Ternary Iron Alloys, Part 5, ASM International, USA, 1989, pp. 43-54.