Effect of Temperature on Fracture Toughness of Timetal 834 Titanium Alloy under Mode I and Mixed Mode I/III Loading
Source abstract
Abstract
The effect of temperature on fracture toughness of Timetal 834 titanium alloy plate under mode I and mixed mode I/III loading was investigated. Both mode I and mixed mode I/III fracture toughness values were initially found to increase as the temperature is increased from room temperature to 723 K. Beyond this temperature, both the fracture toughness values decreased up to 773 K and then showed a significant increase at 823 K. It was also observed that at room temperature, the fracture toughness under mixed mode I/III loading was higher than the corresponding mode I fracture toughness, whereas at 723, 748, and 773 K, the fracture toughness under mixed mode I/III loading was lower than the corresponding mode I fracture toughness, and at 823 K, the two toughness values were comparable. The results were explained on the basis of the occurrence of dynamic strain aging (DSA), change in fracture mechanism, and the nature of the deformation fields ahead of the crack tip under mode I and mixed mode I/III loading.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · Hydrogen embrittlement and corrosion behaviors in metals · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Materials Properties Handbook: Titanium Alloys, R. Boyer, G. Welsch, and E.W. Collings, eds., AMS, Materials Park, OH, 1994, pp. 439–46
2. D.F. Neal: Proc. 6th World Conf. on Titanium, P. Lacombe, R. Tricot, and G. Beranger, eds., Cedex, France, Societe Francaise de Metallurgie des Materiaux, Paris, France, 1988, pp. 253–58
3. D.F. Neal: Development of Timetal 834, TMS, Warrendale, PA, 2001, pp. 199–212
4. B. Borchert and M.A. Daeubler: Proc. 6th World Conf. on Titanium, P. Lacombe, R. Tricot, and G. Beranger, eds., Cedex, France, Societe Francaise de Metallurgie des Materiaux, Paris, France, 1988, pp. 467–72
5. H. Kestler, H. Mughrabi, and H. Renner: Titanium ’95 Science and Technology, The Institute of Materials, London, 1995, pp. 1171–78
6. D.F. Neal: Ti Sci. Technol., G. Luetjering, U. Zwicker, and W. Dunk, eds., Deutsche Gessellschafl fuer Metallkunde, Oberursel, Germany, 1985, pp. 2419–24
7. L.K Pook: Eng. Fract. Mech., 1971, vol. 3, pp. 205–1810.1016/0013-7944(71)90032-4 ↗
8. M. Yoda: Eng. Fract. Mech., 1980, vol. 13, pp. 647–5610.1016/0013-7944(80)90093-4 ↗
9. J.G. Schroth, J.P. Hirth, R.G. Hoagland, A.R. Rosenfield: Metall. Trans. A, 1987, vol. 18A, pp. 1061–7210.1007/BF02668555 ↗
10. S.V. Kamat, J.P. Hirth, R. Mehrabian: Scripta Metall., 1989, vol. 23, pp. 523–2810.1016/0036-9748(89)90444-4 ↗
11. S. Raghavachary, A.R. Rosenfield, J.P. Hirth: Metall. Trans. A, 1990, vol. 21A, pp. 2539–4510.1007/BF02646999 ↗
12. M. Manoharan, J.P. Hirth, A.R. Rosenfield: Acta Metall. Mater., 1991, vol. 39, pp. 1203–1010.1016/0956-7151(91)90208-I ↗
13. J.A. Gordon, J.P. Hirth, A.M. Kumar, N.E. Moody: Metall. Trans. A, 1992, vol. 23A, pp. 1013–2010.1007/BF02675576 ↗
14. N. Eswara Prasad, S.V. Kamat: Metall. Trans. A, 1995, vol. 26A, pp. 1823–3310.1007/BF02670770 ↗
15. S.V. Kamat, J.P. Hirth: Acta Mater., 1996, vol. 44, pp. 1047–5410.1016/1359-6454(95)00223-5 ↗
16. S.V. Kamat, M. Srinivas, P. Rama Rao: Acta Mater., 1998, vol. 46, pp. 4985–9210.1016/S1359-6454(98)00170-0 ↗
17. M. Srinivas, S.V. Kamat, P. Rama Rao: Mater. Sci. Technol., 2004, vol. 20, pp. 235–4210.1179/026708304225011955 ↗
18. S.V. Kamat, J.P. Hirth: J. Eng. Mater. Technol., 1995, vol. 117, pp. 391–9410.1115/1.2804731 ↗
19. D.F. Neal: Forging and Properties of Aerospace Materials, Proc. of Int. Conf., Leeds, UK, Chameleon Press, London, 1978, pp. 199–216
20. G. Luetjering, J. Albrecht, and A. Gysler: Titanium ’92: Science and Technology; Proc. Symp., 7th World Titanium Conf., San Diego, CA, 1993, pp. 1635–46
21. B.S.S. Chandra Rao, M. Srinivas, and S.V. Kamat: Mater. Sci. Eng. A, 2008, vol. 476A, pp. 162–6810.1016/j.msea.2007.05.059 ↗
22. ASTM E-8, Annual Book of ASTM Standards, ASTM, Philadelphia, PA, 2004, vol. 3.01, pp. 62–85
23. S.V. Kamat, M. Srinivas, P. Rama Rao: J. Test. Eval., 2006, vol. 34, pp. 111–1810.1520/JTE12586 ↗
24. M. Srinivas, S.V. Kamat, P. Rama Rao: J. Test. Eval., 1994, vol. 22, pp. 302–0910.1520/JTE11838J ↗
25. M. Srinivas, S.V. Kamat, P. Rama Rao: Mater. Sci. Eng. A, 2007, vol. 443A, pp. 132–4110.1016/j.msea.2006.08.042 ↗
26. K. Prasad and V.K. Varma: doi:10.1016/j.msea.2007.09.02010.1016/j.msea.2007.09.020 ↗
27. N. Singh, N. Prasad, V. Singh: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2547–5210.1007/s11661-999-0263-x ↗
28. N. Singh and V. Singh: doi:10.1016/jmsea.2007.07.06410.1016/jmsea.2007.07.064 ↗
29. H. Sasano, H. Kimura: Nippon Kinnzon Gakkaishi, 1976, vol. 39, pp. 142–52
30. M. Winstone: J. Less Common Met., 1973, vol. 31, pp. 143–5010.1016/0022-5088(73)90137-9 ↗
31. M.R. Bache, W.J. Evans, H.D. Davies: J. Mater. Sci., 1997, vol. 32, pp. 3435–4310.1023/A:1018624801310 ↗
32. M.R. Bache, M. Cope, H.M. Davies, W.J. Evans, G. Harrison: Int. J. Fatigue, 1997, vol. 19, pp. S83–S8810.1016/S0142-1123(97)00020-0 ↗
33. A.S. Argon, J. Im, R. Safoglu: Metall. Trans., 1975, vol. 6, pp. 825–3710.1007/BF02672306 ↗
34. J.R. Rice, R.J. Nicolic: J. Mech. Phys. Solids, 1985, vol. 33, pp. 595–60410.1016/0022-5096(85)90005-5 ↗
35. W.J. Drugan, J.R. Rice, T.L. Sham: J. Mech. Phys. Solids, 1982, vol. 30, pp. 447–6010.1016/0022-5096(82)90027-8 ↗
36. K.C. Wang, X.F. Luo: in Advances in Fracture Research, K. Salama, K. Ravi Chander, D.M.R. Taplin, P. Rama Rao, eds., Pergamon, Oxford, United Kingdom, 1989, vol. 1, pp. 371–78
37. J. Pan, C.F. Shih: J. Mech. Phys. Solids, 1990, vol. 38, pp. 161–7510.1016/0022-5096(90)90032-Y ↗