journal article·2002-02

Interface nanochemistry effects on stainless steel diffusion bonding

M. J. Cox, R. W. Carpenter, M. J. Kim

Publisher page

Abstract

The diffusion-bonding behavior of single-phase austenitic stainless steel depends strongly on the chemistry of the surfaces to be bounded. We found that very smooth (0.5 nm root-mean-square (RMS) roughness), mechanically polished and lapped substrates would bond completely in ultrahigh vacuum (UHV) in 1 hour at 1000 °C under 3.5 MPa uniaxial pressure, if the native oxide on the substrates was removed by ion-beam cleaning, as shown by in-situ Auger analysis. No voids were observed in these bonded interfaces by transmission electron microscopy (TEM), and the strength was equal to that of the unbounded bare material. No bond formed between the substrates if in-situ ion cleaning was not used. The rougher cleaned substrates partially bonded, indicating that roughness, as well as native oxides, reduced the bonding kinetics.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: 3D IC and TSV technologies · Electronic Packaging and Soldering Technologies · Nanofabrication and Lithography Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. M.F. Islam and N. Ridley: Scripta Mater., 1998, vol. 38 (8), pp. 1187–93.10.1016/S1359-6462(98)00037-2 ↗
2. H. Kokawa, T. Tsuzuki, and T. Kuwana: Iron Steel Inst. Jpn. Int., 1995, vol. 35 (10), pp. 1291–97.10.2355/isijinternational.35.1291 ↗
3. Q.-Y. Tong and U. Gosele: Semiconductor Wafer Bonding, John Wiley & Sons, Inc., New York, NY, 1999.
4. B. Derby and E.R. Wallach: Met. Sci., 1982, vol. 16, pp. 49–56.10.1016/0036-9748(82)90401-X ↗
5. Y. Takahashi and K. Inoue: Mater. Sci. Technol., 1992, vol. 8, pp. 953–64.10.1179/mst.1992.8.11.953 ↗
6. M.J. Kim, Hong Xu, R.-J. Liu, M.J. Cox, and R.W. Carpenter: Mater. Res. Soc. Symp., 2000, vol. 587 (C), p. 04.2.1–6.
7. N. Ridley, M.T. Salehi, and J. Piling: Mater. Sci. Technol., 1992, vol. 8, pp. 791–95.10.1179/mst.1992.8.9.791 ↗
8. R.I. Todd, C.S. Hodges, Y.C. Wong, Z.C. Wang, and N. Ridley: Mater. Sci. Forum, 1997, vol. 243, pp. 675–80.10.4028/www.scientific.net/MSF.243-245.675 ↗
9. M.J. Kim, R.W. Carpenter, M.J. Cox, and J. Xu: J. Mater. Res., 2000, vol. 15 (4), pp. 1008–16.10.1557/JMR.2000.0144 ↗
10. S. Hofmann: J. Vac. Sci. Technol. A, 1986, vol. 4 (6), pp. 2789–96.10.1116/1.573680 ↗
11. R. Bouwman, J.B. van Mechelen, and A.A. Holscher: J. Vac. Sci. Technol. A, 1978, vol. 15 (1), pp. 91–94.10.1116/1.569444 ↗
12. D.N. Ruzic, G.A. Gerdin, and C.M. Loxton: J. Vac. Sci. Technol. A, 1986, vol. 4 (3), pp. 1232–35.10.1116/1.573404 ↗
13. P.D. Townsend, J.C. Kelly, and N.E.N. Hartley: Ion Implantation, Sputtering, and Their Applications, Academic Press, New York, NY, 1976, pp. 111–47.
14. J. Piling: Mater. Sci. Eng., 1988, vol. 100, pp. 137–44.10.1016/0025-5416(88)90249-2 ↗
15. M.T. Salehi, J. Piling, N. Ridley, and D.L. Hamilton: Mater. Sci. Eng. A, 1992, vol. 150, pp. 1–6.10.1016/0921-5093(90)90002-K ↗
16. M.J. Cox, M.J. Kim, Hong Xu, and R.W. Carpenter: Microsc. Microanal., 2000, vol. 6 (2, Proc.), pp. 1075–76.