journal article·2011-03

Experimental Comparison of the Effects of Nanometric and Micrometric Particulates on the Tensile Properties and Fracture Behavior of Al Composites at Room and Elevated Temperatures

Adnan Ahmed, Andrew J. Neely, Krishna Shankar

Publisher page

Abstract

This article studies the influence of nanometric (n-SiCp) and micrometric-scale SiC particulates (μ-SiCp) on the tensile properties of the Al 7075 alloy. The unreinforced Al and its composites were synthesized using the powder metallurgy (P/M) route and were tested uniaxially in tension at both room and elevated temperatures. Aging behavior was studied to observe any effect of the reinforcement on the aging kinetics and hardness of the composites. X-ray diffraction was performed to determine the crystal structures of the raw materials and any reaction phase formed in the composites. The n-SiCp were not dispersed uniformly in the Al matrix and clustered mainly at the grain boundaries. The stiffness of the composites increased and the ductility decreased with an increase in the volume fraction of the n-SiCp. The n-SiCp proved to be a better reinforcement than the traditional μ-SiCp in terms of imparting higher ductility to the composite. Fractography and microscopy using optical, scanning electron, and transmission electron microscopes were performed for failure and microstructural analysis of all the materials. At room temperature, the fracture altered from ductile in the unreinforced Al to brittle in the composites. At an elevated temperature, the fracture mechanism transformed from brittle to ductile rupture in the composites.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. T.W. Clyne and P.J Withers: An Introduction to Metal Matrix Composites, University Press, Cambridge, MA, 1993.10.1017/CBO9780511623080 ↗
2. M. Taya and R.J. Arsenault: Metal Matrix Composites Thermomechanical Behavior, Pergamon Press, Oxford, UK, 1989.
3. N. Chawla and K.K. Chawla: Metal Matrix Composites, Springer, New York, NY, 2006.10.1007/b101197 ↗
4. M. Vedani and E. Gariboldi: Acta Mater., 1996, vol. 44, pp. 3077-88.10.1016/1359-6454(95)00437-8 ↗
5. M. Vedani, F. D’Errico, and E. Gariboldi: Compos. Sci. Technol., 2006, vol. 66, pp. 343-49.10.1016/j.compscitech.2005.04.045 ↗
6. J. Llorca and P. Poza: Scripta Metall. Mater., 1993, vol. 29, pp. 261-66.10.1016/0956-716X(93)90319-N ↗
7. D.L. McDaniels: Metall. Mater. Trans. A, 1985, vol. 16A, pp. 1105-15.10.1007/BF02811679 ↗
8. T.S. Srivatsan: J. Mater. Sci., 1996, vol. 31, pp. 1375-88.10.1007/BF00353120 ↗
9. D.L. Davidson: Eng. Fract. Mech., 1989, vol. 33, pp. 965-77.10.1016/0013-7944(89)90111-2 ↗
10. S. Dermarkar: Met. Mater., 1986, vol. 2, pp. 144-47.
11. J. Yang, C. Cady, M.S. Hu, and F. Zok: Acta Metall. Mater., 1990, vol. 38, pp. 2613-19.10.1016/0956-7151(90)90273-J ↗
12. J.M. Papazian and P.N. Adler: Metall. Trans. A, 1990, vol. 21A, pp. 401-10.10.1007/BF02782420 ↗
13. J.J. Lewandowski, C. Liu, and W.H. Hunt: Mater. Sci. Eng. A, 1989, vol. 107, pp. 241-55.10.1016/0921-5093(89)90392-4 ↗
14. R. Arone, O. Botstein, and B. Shpigler: Isr. J. Technol., 1988, vol. 24, pp. 393-99.
15. M. Tan, Q. Xin, Z. Li, and B.Y. Zong: J. Mater. Sci., 2001, vol. 36, pp. 2045-53.10.1023/A:1017591117670 ↗
16. T.S. Srivatsan, M. Al-Hajri, C. Smith, and M. Petraroli: Mater. Sci. Eng., A, 2003, vol. 346, pp. 91-100.10.1016/S0921-5093(02)00481-1 ↗
17. W.R. East: Mater. Eng., 1988, vol. 23, pp. 33-36.
18. T.C. Willi: Met. Mater., 1988, vol. 20, pp. 485-88.
19. R. Demeis: Aero. Am., 1989, vol. 27, pp. 26-28.
20. T. Das, P.R. Munroe, and S. Bandyopadhyay: Int. J. Mater. Prod. Tech., 2003, vol. 19, pp. 218-27.10.1504/IJMPT.2003.002507 ↗
21. K. Niihara: J. Ceram. Soc. Jpn., 1991, vol. 99, pp. 974-82.10.2109/jcersj.99.974 ↗
22. Z.Y. Ma, S.C. Tjong, Y.L. Li, F. Zheng, and Y. Liang: Mater. Sci. Eng., A, 1996, vol. 219, pp. 229-31.10.1016/S0921-5093(96)10444-5 ↗
23. Y.C. Kang and S.L.I. Cha: Mater. Chem. Phys., 2004, vol. 85, pp. 438-43.10.1016/j.matchemphys.2004.02.002 ↗
24. Y.C. Kang: Ph.D. Dissertation, National Taiwan University, Taiwan, R.O.C., 2004.
25. T.J.A. Doel and P. Bowen: Compos. Appl. Sci. Manuf., 1996, vol. 27, pp. 655-65.10.1016/1359-835X(96)00040-1 ↗
26. A. Razaghian, D. Yu, T. Chandra: Compos. Sci. Technol., 1998, vol. 58, pp. 293-98.10.1016/S0266-3538(97)00130-9 ↗
27. A.B. Pandey, B.S. Majumdar, and D.B. Miracle: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 921-36.10.1007/s11661-000-1011-4 ↗
28. R. Zheng: Master’s Thesis, University of New South Wales, Sydney, Australia, 2007.
29. A. Ahmed, A.J. Neely, K. Shankar, P. Nolan, S. Moricca, and T. Eddowes: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1582-91.10.1007/s11661-010-0201-y ↗
30. A. Ahmed, A.J. Neely, K. Shankar, and S.L.I. Chan: Mater. Sci. Forum., 2007, vol. 561-565, pp. 761-64.10.4028/www.scientific.net/MSF.561-565.761 ↗
31. T.W. Butler and D.C. Drucker: J. Appl. Mech., 1973, vol. 40, pp. 780-88.10.1115/1.3423089 ↗
32. T. Christman, A. Needleman, S.R. Nutt, and S. Suresh: Mater. Sci. Eng. A, 1989, vol. 107, pp. 49-61.10.1016/0921-5093(89)90374-2 ↗
33. F.A. McClintock: On the Mechanics of Fracture from Inclusions, Ductility, ASM, Materials Park, OH, 1968, pp. 255-77.
34. R.H. Van Stone, T.B. Cox, J.R. Low, Jr., and J.A. Psioda: Int. Met. Rev., 1975, vol. 30, pp. 157-71.
35. J.K. Shang and R.O. Ritchie: Acta Metall., 1989, vol. 37, pp. 2267-78.10.1016/0001-6160(89)90154-5 ↗
36. L.E.G. Cambronero, E. Sanchez, J.M. Ruiz-Roman, and J.M. Ruiz-Prieto: J. Mater. Process. Tech., 2003, vol. 143-144, pp. 378-83.10.1016/S0924-0136(03)00424-2 ↗
37. N.V. Ravi Kumar and E.S. Dwarakadasa: J. Mater. Sci., 1994, vol. 29, pp. 1533-39.10.1007/BF00368921 ↗
38. E. Orowan: Symposium on Internal Stress in Metals and Alloys, Institute of Metals, London, UK, 1948, pp. 451-88.
39. D. Brookbank and K.W. Andrews: J. I. S. I., 1969, vol. 207, pp. 474-83.
40. T.S. Srivatsan and P.C. Lam: Alum. Trans., 2000, vol. 2, pp. 19-26.
41. D. Kumar, G.S. Murty, and M.L. Vaidya: Tensile Strength and Fracture Toughness of Particulate SiC-2124, High Performance Composites: Commonalty of Phenomena, Eds. K.K. Chawla, P.K. Liaw, and S.G. Fishman, TMS, New York, NY, 1994, pp. 347-59.