journal article·2005-12

Direct observations of the α → γ transformation at different input powers in the heat-affected zone of 1045 C-Mn steel arc welds observed by spatially resolved X-ray diffraction

T. A. Palmer, J. W. Elmer

Publisher page

Abstract

Spatially resolved X-ray diffraction (SRXRD) experiments have been performed during gas tungstenarc (GTA) welding of AISI 1045 C-Mn steel at input powers ranging from 1000 to 3750 W. In-situ diffraction patterns taken at discreet locations across the width of the heat-affected zone (HAZ) near the peak of the heating cycle in each weld show regions containing austenite (γ), ferrite and austenite (α+γ), and ferrite (α). Changes in input power have a demonstrated effect on the resulting sizes of these regions. The largest effect is on the γ phase region, which nearly triples in width with increasing input power, while the width of the surrounding two-phase α+γ region remains relatively constant. An analysis of the diffraction patterns obtained across this range of locations allows the formation of austenite from the base-metal microstructure to be monitored. After the completion of the α → γ transformation, a splitting of the austenite peaks is observed at temperatures between approximately 860 °C and 1290 °C. This splitting in the austenite peaks results from the dissolution of cementite laths originally present in the base-metal pearlite, which remain after the completion of the α → γ transformation, and represents the formation of a second more highly alloyed austenite constituent. With increasing temperatures, carbon, originally present in the cementite laths, diffuses from the second newly formed austenite constituent to the original austenite constituent. Eventually, a homogeneous austenitic microstructure is produced at temperatures of approximately 1300 °C and above, depending on the weld input power.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. G.R. Speich, V.A. Demarest, and R.L. Miller: Metall. Trans. A, 1981, vol. 12A, pp. 1419–28.10.1007/BF02643686 ↗
2. A. Jacot, M. Rappaz, and R.C. Reed: Acta Mater., 1998, vol. 46 (11), pp. 3949–62.10.1016/S1359-6454(98)00048-2 ↗
3. A. Jacot and M. Rappaz: Acta Mater., 1997, vol. 45 (2), pp. 575–85.10.1016/S1359-6454(96)00199-1 ↗
4. A. Jacot and M. Rappaz: Acta Mater., 1998, vol. 47 (5), pp. 1645–51.10.1016/S1359-6454(99)00005-1 ↗
5. C. Atkinson, T. Akbay, and R.C. Reed: Acta Metall. Mater., 1995, vol. 43 (5), pp. 2013–31.10.1016/0956-7151(94)00366-P ↗
6. D. Gaude-Fugarolas and H.K.D.H. Bhadeshia: J. Mater. Sci., 2003, vol. 38, pp. 1195–1201.10.1023/A:1022805719924 ↗
7. F.G. Caballero, C. Capdevila, D. San Martín, and C. García De Andrés: in Austenite Formation and Decomposition, E.B. Damm and M. Merwin, eds., ISS/TMS, Warrendale, PA, 2003, pp. 457–74.
8. C.R. Brooks: Principles of the Austenitization of Steels, Kluwer Academic Publishers, Dordrecht, 1992.
9. S. Estay, L. Chengji, and G.R. Purdy: Can. Metall. Q., 1984, vol. 23 (1), pp. 121–30.10.1179/cmq.1984.23.1.121 ↗
10. R.C. Reed, T. Akbay, Z. Shen, J.M. Robinson, and J.H. Root: Mater. Sci. Eng. A, 1998, vol. 256, pp. 152–65.10.1016/S0921-5093(98)00800-4 ↗
11. T. Akbay, R.C. Reed, and C. Atkinson: Acta Metall. Mater., 1994, vol. 47 (4), pp. 1469–80.10.1016/0956-7151(94)90165-1 ↗
12. Z. Shen, T. Akbay, J.P. Bourne, and R.C. Reed: in Trends in Welding Research, H.B. Smartt, J.A. Johnson, and S.A. David, eds., ASM INTERNATIONAL, Materials Park, OH, 1996, pp. 217–22.
13. M. Hillert, K. Nilsson, and L.-E. Törndahl: J. Iron Steel Inst., 1971, vol. 209, pp. 49–66.
14. M. Nemoto: Metall. Trans. A, 1977, vol. 8A, pp. 431–37.10.1007/BF02661753 ↗
15. K. Easterling: Introduction to the Physical Metallurgy of Welding, 2nd ed., Butterworth-Heinemann, Oxford, United Kingdom, 1992.
16. S. Kou: Welding Metallurgy, 2nd ed., Wiley-Interscience, Hoboken, NJ, 2003.
17. J.W. Elmer, T.A. Palmer, and S.S. Babu: Adv. Mater. Processing, 2002, vol. 160 (11), pp. 23–26.
18. J.W. Elmer, J. Wong, and T. Ressler: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2761–73.10.1007/s11661-998-0317-5 ↗
19. Z. Yang, J.W. Elmer, J. Wong, and T. DebRoy: Welding J., 2000, vol. 79 (4), pp. 97s-111s.
20. J.W. Elmer, J. Wong, and T. Ressler: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1175–88.10.1007/s11661-001-0127-5 ↗
21. J.W. Elmer, J. Wong, and T. Ressler: Scripta Mater., 2000, vol. 43 (8), pp. 751–57.10.1016/S1359-6462(00)00481-4 ↗
22. T.A. Palmer, J.W. Elmer, and J. Wong: Sci. Technol. Welding Joining, 2002, vol. 7 (3), pp. 159–71.10.1179/136217102225004194 ↗
23. J.W. Elmer, T.A. Palmer, W. Zhang, B. Wood, and T. DebRoy: Acta Mater., 2003, vol. 51, pp. 3333–49.10.1016/S1359-6454(03)00049-1 ↗
24. W. Zhang, J.W. Elmer, and T. DebRoy: Scripta Mater., 2002, vol. 46, pp. 753–57.10.1016/S1359-6462(02)00040-4 ↗
25. W. Zhang, J.W. Elmer, and T. DebRoy: Mater. Sci. Eng. A, 2002, vol. 333 (1–2), pp. 320–35.10.1016/S0921-5093(01)01857-3 ↗
26. J.W. Elmer, T.A. Palmer, and J. Wong: J. Appl. Phys., 2003, vol. 93 (4), pp. 1941–47.10.1063/1.1537464 ↗
27. J.W. Elmer, T.A. Palmer, S.S. Babu, W. Zhang, and T. DebRoy: Welding J., 2004, vol. 83 (9), pp. 244s-53s.
28. V. Karpenko, J.H. Kinney, S. Kulkarni, K. Neufeld, C. Poppe, K.G. Tirsell, J. Wong, J. Cerino, T. Troxel, J. Yang, E. Hoyer, M. Green, D. Humpries, S. Marks, and D. Plate: Rev. Sci. Instrum., 1989, vol. 60, pp. 1451–60.10.1063/1.1140961 ↗
29. B.D. Cullity and S.R. Stock: Elements of X-Ray Diffraction, 3rd ed., Prentice-Hall, Upper Saddle River, NJ, 2001.
30. S.A. David and T. DebRoy: Science, 1992, vol. 257, pp. 497–502.10.1126/science.257.5069.497 ↗
31. T. DebRoy and S.A. David: Rev. Mod. Phys., 1995, vol. 67 (1), pp. 85–112.10.1103/RevModPhys.67.85 ↗
32. K. Mundra, T. DebRoy, and K.M. Kelkar: Num. Heat Transfer A, 1996, vol. 29, pp. 115–29.10.1080/10407789608913782 ↗
33. Z. Yang and T. DebRoy: Metall. Mater. Trans. B, 1999, vol. 30B, pp. 483–93.10.1007/s11663-999-0082-x ↗
34. Smithells Metals Reference Book, 7th ed., E.A. Brandes, ed., Butterworth and Heinemann, London, 1992.
35. M.W. Chase, Jr., C.A. Davies, J.R. Downey, Jr., D.J. Frurip, R.A. Mcdonald, and A.N. Syverud: JANAF Thermochemical Tables, 3rd ed., American Chemical Society and American institute for Physics, Washington, DC, 1985.
36. J. Wong, T. Ressler, and J.W. Elmer: J. Synchrotron Rad., 2003, vol. 10, pp. 154–67.10.1107/S0909049502020289 ↗
37. T.A. Palmer and J.W. Elmer: Scripta Mater., 2005, vol. 53, pp. 535–40.10.1016/j.scriptamat.2005.04.050 ↗
38. L. Cheng, A. Böttger, T.H. de Keijser, and E.J. Mittemeijer: Scripta Metall. Mater., 1990, vol. 24, pp. 509–14.10.1016/0956-716X(90)90192-J ↗
39. M. Onink, C.M. Brakman, F.D. Tichelaar, E.J. Mittemeijer, S. van der Zwaag, J.H. Root, and N.B. Konyer: Scripta Metall. Mater., 1993, vol. 29, pp. 1011–16.10.1016/0956-716X(93)90169-S ↗
40. D.J. Dyson and B. Holmes: J. Iron Steel Inst., 1970, vol. 208, pp. 469–74.
41. S.S. Babu: Oak Ridge National Laboratory, Oak Ridge, TN, private communication, 2005.