journal article·2008-12

Effects of Applied Load on 6061-T6 Aluminum Joined Employing a Novel Friction Bonding Process

Douglas E. Burkes, Neil P. Hallinan, Karen L. Shropshire, Peter B. Wells

Publisher page

Abstract

Friction bonding is under consideration for use in mass production of plate-type nuclear fuels for research reactors. This article discusses the effects of applied load (the most important process parameter for fabrication of these fuels) on temperature distribution, microstructure, and mechanical properties. Friction bonding experiments showed that tool geometry caused temperature gradients across the tool surface. Temperatures at the joint interface suggested the advancing side of the tool produced a majority of the frictional heat, while the retreating side of the tool mainly forged the plasticized material while bonding increased with applied load. The microstructure across the tool surface was also altered and, as a function of applied load, affected the mechanical properties. The 6061 aluminum alloy had mechanical properties close to a T4 temper after processing. Results documented in this article will aid in continual enhancement of friction bonding for nuclear fuel plate fabrication, and will hopefully contribute to continued advancement of friction stir welding (FSW) state of the art.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. W.J. Arbegast: Friction Stir Welding and Processing IV, TMS, Warrendale, PA, 2007, pp. 3–18
2. R.S. Mishra, Z.Y. Ma: Mater Sci. Eng. R, 2005, vol. 50, pp. 1–7810.1016/j.mser.2005.07.001 ↗
3. R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, A.K. Mukherjee: Scripta Mater., 1999, vol. 42, pp. 163–6810.1016/S1359-6462(99)00329-2 ↗
4. R.S. Mishra, M.W. Mahoney: Mater. Sci. Forum, 2001, vols. 357–359, p. 50710.4028/www.scientific.net/MSF.357-359.507 ↗
5. http://www.nnsa.doe.gov/nuclearnp.htm#1, accessed on Jan. 14, 2008
6. D.E. Burkes, N.P. Hallinan, and C.R. Clark: Weld. J., Sep. 2008, pp. 1–7, accepted
7. ASM Handbook, vol. 2, Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, 10th ed., ASM INTERNATIONAL, Materials Park, OH, 1990
8. G. Liu, L.E. Murr, C.S. Niou, J.C. McClure, F.R. Vega: Scripta Mater., 1997, vol. 37 (3), pp. 355–6110.1016/S1359-6462(97)00093-6 ↗
9. L.E. Murr, G. Liu, J.C. McClure: J. Mater. Sci., 1998, vol. 33, pp. 1243–5110.1023/A:1004385928163 ↗
10. W. Tang, X. Guo, J.C. McClure, L.E. Murr: J. Mater. Process. Manufact. Sci., 1998, vol. 7, p. 16310.1106/55TF-PF2G-JBH2-1Q2B ↗
11. S. Benavides, Y. Li, L.E. Murr, D. Brown, J.C. McClure: Scripta Mater., 1999, vol. 41 (8), pp. 809–1510.1016/S1359-6462(99)00226-2 ↗
12. C.G. Rhodes, M.W. Mahoney, W.H. Bingel: Scripta Mater., 1997, vol. 36 (1), pp. 69–7510.1016/S1359-6462(96)00344-2 ↗
13. K.N. Krishnan: Mater. Sci. Eng. A, 2002, vol. A327, pp. 246–5110.1016/S0921-5093(01)01474-5 ↗
14. P. Colegrove, H. Shercliff: in Friction Stir Welding and Processing II, K.V. Jata, M.W. Mahoney, R.S. Mishra, S.L. Semiating, T. Leinert, eds., TMS, Warrendale, PA, 2003, pp. 13–22
15. M. James, M. Mahoney, and D.J. Waldron: Proc. 1st Int. Symp. on Friction Stir Welding, Thousand Oaks, CA, 1999
16. G. Biallas, R. Braun, C. Dalle Donne, G. Staniek, and W.A. Kaysser: 1st Int. Conf. on Friction Stir Welds, Thousand Oaks, CA, 1999
17. W.J. Arbegast: in Friction Stir Welding and Processing III, K.V. Jata, M.W. Mahoney, R.S. Mishra, T.J. Leinart, eds., TMS, Warrendale, PA, 2005, pp. 193–204
18. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, R.A. Spurling, W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955–6410.1007/s11661-998-0021-5 ↗
19. A. von Strombeck, J.F. dos Santos, F. Torster, and M. Kocak: Proc. 1st Int. Symp. on Friction Stir Welding, Thousand Oaks, CA, 1999
20. R.S. Mishra, S.R. Sharma, N.A. Mara, M.W. Mahoney: Proc. Int. Conf. on Joining of Advanced and Specialty Materials III, ASM INTERNATIONAL, Materials Park, OH, 2000, p. 157