Strength and failure behavior of stitched carbon/epoxy composites
Source abstract
Abstract
This article presents a study of the effect of through-the-thickness stitching yarns upon the strength and failure behavior of multidirectionally reinforced composites. The in-plane yarns were placed in four directions (0,±45, 90) to form a quasi-isotropic preform, which had open spaces between adjacent yarns. These interyarn spaces allowed easy insertion of the through-the-thickness stitching yarns without significant damage of the in-plane fibers. Fiber volume fractions of over 54 pct were obtained by this method. The through-the-thickness yarn sizes used in this study were 2, 4, and 6 kilo-filament (kf). Non-stitched performs were also manufactured with the same fiber content and by the same procedure as the stiched preforms for the control experiments. All preforms were infiltrated with epoxy resin by the resin transfer molding (RTM) technique. In-plane tensile and compressive strength, interlaminar shear strength, and mode I fracture toughness of the carbon/epoxy composites were measured at three through-the-thickness yarn contents. Although the through-the-thickness yarns significantly enhanced the mode I fracture toughness, they tended to degrade the in-plane tensile and compressive strength. The failure process under interlaminar shear loading by double notch shear tests showed two distinct stages: the fiber-matrix interfacial failure followed by the breakage/debonding of the through-the-thickness yarns. The through-the-thickness yarns caused a reduction of the initial failure load in the first stage but could enhance the final failure load in the second stage. In composites with 6 kf through-the-thickness yarns, the final failure load could exceed the initial failure load. Scanning electron microscope (SEM) and optical microscopic examinations were also conducted for observing the failure mechanisms and fracture surfaces.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Innovative concrete reinforcement materials · Epoxy Resin Curing Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. R. Kamiya: Master’s Thesis, University of Delaware, Newark, DE 1998.
2. M.Z. Shah Khan and A.P. Mouritz: Composites Sci. Technol., 1996, vol. 56(6), pp. 695–701.10.1016/0266-3538(96)00052-8 ↗
3. H. Harris, N. Schinske, R. Krueger, and B. Swanson: 36th Int. SAMPE Symp. Exhib., Apr. 15–18, 1991, SAMPE, Covina, CA, 1991, vol. 36(1), pp. 521–35.
4. I. Herstberg and M.K. Bannister: National Conference Publication-Institution of Engineers, Aus. Proc. 5th Australian Aeronautical Conf., Sept. 1993, Part 1, IE Australian Crows Nest, NSW Australia, 1993, vol. 1(93), part 6, pp. 213–18.
5. Y. Ogo: Master’s Thesis, University of Delaware, Newark, DE, 1987.
6. X. Du, F. Xue, and Z. Gu: Proc. Int. Symp. of Composite Materials and Structures, Technomic, Lancaster, PA, 1986, pp. 912–18.
7. B.H. Dexter, J.G. Funk: Collection of Technical Papers-AIAA/ASME/ASCE/AHS 27th Structures, Structural Dynamics and Materials Conf. Part I: Structures and Materials, AIAA, New York, NY, 1986, vol. 1, pp. 700–09.
8. K.W. Furrow and A.C. Loos: J. Reinforced Plastic Composites, 1996, vol. 15, pp. 378–419.10.1177/073168449601500403 ↗
9. J.R. Reeder: J. Composite Mater., 1995, vol. 29(18), pp. 2464–87.10.1177/002199839502901805 ↗
10. I. Herszberg and M.K. Bannister: National Conference Publication-Institution of Engineers, Aus. Proc. 5th Australian Aeronautical Conf., IE Australian Crows Nest, NSW Australia, Sept. 1993, pp. 13–15.
11. B.N. Cox: 9th DoD/NASA/FAA Conf. on Fibrous Composites in Structural Design, Lake Tahoe, NV, Nov. 1991, FAA Technical Center, Atlantic City, NJ, 1992, pp. 1105–10.
12. G.L. Farley, B.T. Smith, and J. Maiden: J. Reinforced Plastics Composites, 1992, vol. 11, pp. 787–810.10.1177/073168449201100705 ↗
13. G.L. Farley and L.C. Dickinson: J. Reinforced Plastics Composites, 1992, vol. 11, pp. 633–42.10.1177/073168449201100604 ↗
14. M.A. Portanova, C.C. Poe, and J.D. Whitcomb: 10th Conf. on Composite Materials: Testing and Design, ASTM STP, 1120, ASTM, Philadelphia, PA, 1992, pp. 37–53.
15. M.B. Dow and D.L. Smith: 21st Int. SAMPE Tech. Conf., SAMPE, Covina, CA, Sept. 1989, pp. 595–605.
16. D. Shu and Y.-W. Mai: Composites Sci. Technol., 1993, vol. 47, pp. 25–33.10.1016/0266-3538(93)90092-U ↗
17. D. Shu, and Y.-W. Mai: Composite Sci. Technol., 1993, vol. 47, pp. 35–41.10.1016/0266-3538(93)90093-V ↗
18. D. Shu, and Y.-W. Mai: Composite Sci. Technol., 1993, vol. 49, pp. 165–71.10.1016/0266-3538(93)90056-M ↗
19. L.K. Jain and Y.W. Mai: Composites Sci. Technol., 1994, vol. 51, pp. 331–45.10.1016/0266-3538(94)90103-1 ↗
20. L.K. Jain and Y.W. Mai: Appl. Composite Mater., 1994, vol. 1(1), pp. 1–17.10.1007/BF00567208 ↗
21. L.K. Jain and Y.W. Mai: Int. J. Fract., 1994, vol. 68, pp. 219–44.10.1007/BF00013069 ↗
22. L.K. Jain and Y.W. Mai: Fat. Fract. Eng. Mater. Struct., 1994, vol. 17(3) pp. 399–50.10.1111/j.1460-2695.1994.tb00234.x ↗
23. L.K. Jain and Y.W. Mai: Composites Sci. Technol., 1995, vol. 55, pp. 241–53.10.1016/0266-3538(95)00089-5 ↗
24. V. Sonic and B.V. Sankar: ASME Aerospace Division Proc. Int. Mechanical Engineering Congr. Exp., ASME, New York, NY, 1996, vol. S2, pp. 61–69.
25. V.L. Chen, X.X. Wu, and C.T. Sun: Proc. 8th Techn. Conf. of the American Society for Composites, Technomic Publishing Co., Inc., Lancaster, PA, Oct. 19–21, 1993, 1994, pp. 453–62.
26. A.P. Mouritz: Composites Sci Technol., 1995, pp. 365–74.10.1016/0266-3538(95)00122-0 ↗
27. A.P. Mouritz and L.K. Jain: 11th Int. Conf. on Composite Materials (ICCM 11), The Metallurgical Society, Inc., Warrendale, PA, 1997, vol. 5, pp. 116–27.
28. M. Ji, H. Ishikawa, M. Anahara, and Y. Yasui: JSME Int. J. Ser. A: Mech. Mater. Eng., 1997, vol. 40(1), pp. 37–43.
29. S.K. Sharma and B.V. Sankar: J. Thermoplastic Composite Mater., 1997, vol. 10, pp. 241–53.10.1177/089270579701000302 ↗
30. S.K. Sharma and B.V. Sankar: J. Reinforced Plastic Composites, 1997, vol. 16(5), pp. 425–34.10.1177/073168449701600503 ↗
31. S.K. Sharma and B.V. Sankar: ASME Aerospace Division Proc. Int. Mechanical Engineering Congr. Exp., ASME, New York, NY, 1996, vol. 52, pp. 39–50.
32. S.K. Sharma and B.V. Sankar: “AEMES-TR-95-1-05,” University of Florida, Gainesville, FL, Jan. 1995, pp. 1–118.
33. S.K. Sharma and B.V. Sankar: ASME Materials Division Proc. Int. Mech. Eng. Congr. Exp. Part I ASME, New York, NY, 1995, vol. 69(1), pp. 299–310.
34. K.A. Dransfield, L.K. Jain, and Y.W. Mai: Composites Sci. Technol., 1998, vol. 58, pp. 815–27.10.1016/S0266-3538(97)00229-7 ↗
35. L.K. Jain, K.A. Dransfield, and Y.W. Mai: Composites Sci. Technol., 1998, vol. 58, pp. 829–37.10.1016/S0266-3538(97)00186-3 ↗
36. Y. Yasui, F. Hori, M. Amano, and J. Takeuchi: U.S. Patent 5,772,821, Jun. 30, 1998, Kabushiki Kaisha Toyoda Jidoshokki Seisakusho, Kariya, Japan, 1998.
37. V.A.E. Guenon: Master’s Thesis in Mechanical Engineering, University of Delaware, Newark, DE, 1987.
38. T. Ishikawa, M. Matsushima, K. Bansaku, N. Watanabe, and M. Sunakawa: Proc. Sem. Japan Society for Composite Materials, Japan Society for Composite Materials, Tokyo, Japan, 1996, pp. 51–52 (in Japanese).