Effect of intermediate annealing on texture evolution and plastic anisotropy in an Al-Mg autobody alloy
Source abstract
Abstract
The effect of intermediate annealing (IA) on texture evolution and plastic anisotropy of an Al-Mg autobody sheet was investigated. The formation of annealing textures after two kinds of final heat treatments was discussed with the aid of microstructural characterization. The results showed that the IA treatment had obvious influences on the final annealing texture as well as the resulting plastic anisotropy. It led to relatively lower recrystallization extent and stronger retained rolling orientations in the sheets after final heat treatment. The final annealing textures were very weak due to the dominant influence of particle stimulated nucleation. The other orientations occurring can either be attributed to genuine recrystallization or to recrystallization in situ. As a result of good suppression of the cube and rotated cube orientations, a good combination of normal anisotropy and planar anisotropy was achieved in the sample with IA and after O treatment.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. M. Koizumi, H. Okudaira, and H. Inagaki: Z. Metallkd., 1998, vol. 89, pp. 424–32.
2. P. Ratchev, B. Verlinden, and P. Van Houtte: Acta Metall. Mater., 1995, vol. 43, pp. 621–29.10.1016/0956-7151(94)00261-F ↗
3. K. Lucke and O. Engler: Mater. Sci. Technol., 1990, vol. 6, pp. 1113–30.10.1179/mst.1990.6.11.1113 ↗
4. P. Wagner, O. Engler, and K. Lucke: Acta Metall. Mater., 1995, vol. 43, pp. 3799–3812.10.1016/0956-7151(95)90164-7 ↗
5. H. Takuda, N. Yamazaki, N. Hatta, and S. Kikuchi: J. Mater. Sci., 1995, vol. 30, pp. 957–63.10.1007/BF01178430 ↗
6. Y.S. Liu, S. B. Kang, and H. S. Ko: Scripta Mater., 1997, vol. 37, pp. 411–17.10.1016/S1359-6462(97)00102-4 ↗
7. H.-J. Bunge: Texture Analysis in Materials Science, Butterworth and Co., London, 1982.
8. G.M. Raynaud, B. Grange, and C. Sigli: Proc. 3rd Int. Conf. on Aluminum Alloys (ICAA-3), L. Arnberg, O. Lohne, E. Nes, and N. Ryum, eds., The Norwegian Institute of Technology, Trondheim, Norway, 1992, vol. 3, pp. 169–213.
9. F.J. Humphreys: Acta Metall., 1977, vol. 25, pp. 1323–44.10.1016/0001-6160(77)90109-2 ↗
10. O. Engler, I. Heckelmann, T. Rickert, J. Hirsch, and K. Lucke: Mater. Sci. Technol., 1994, vol. 10, pp. 771–81.10.1179/mst.1994.10.9.771 ↗
11. E. Nes and H.E. Vatne: Z. Metallkd., 1996, vol. 87, pp. 448–53.
12. H.E. Vatne, T. Furu, and E. Nes: Mater. Sci. Technol., 1996, vol. 12, pp. 201–10.10.1179/mst.1996.12.3.201 ↗
13. K. Lucke and O. Engler: Proc. 3rd Int. Conf. on Aluminum Alloys (ICAA-3), L. Arnberg, O. Lohne, E. Nes, and N. Ryum, eds., The Norwegian Institute of Technology, Trondheim, Norway, 1992, vol. 3, pp. 439–52.
14. P. Van Houtte: The MTM-FHM Software System, Version 2, Katholeke Universiteit Leuven, Leuven, Belgium, 1995.