journal article·2005-12

Studies of retrogression and reaging behavior in a 1441 Al-Li-Cu-Mg-Zr alloy

K. S. Ghosh, K. Das, U. K. Chatterjee

Publisher page

Abstract

A 1441 Al-Li-Cu-Mg-Zr alloy in the peak-aged T8 temper was subjected to retrogression treatment and immediately reaged to various tempers. Transmission electron microscopy (TEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), hardness measurements, tensile testing, scanning electron microscopy (SEM) fractography, and electrochemical polarization studies have been made to characterize the retrogression and the retrogression and reaging (RRA) behavior of the alloy. Retrogression of the T8 temper causes dissolution of δ′ (Al3Li) precipitates into solid solution, resulting in a decrease of hardness and tensile strength and an increase of ductility. Reaging the retrogressed state causes restoration of strength and ductility properties because of the reprecipitation of the δ′ phase in the matrix, confirmed by TEM, XRD, and DSC studies and image analysis. The SEM fractographs revealed predominantly intergranular fracture in all the tempers due to strain localization at the grain boundaries. The gross aging time of the RRA tempers approaches that of the over-aged T7 temper, which would contribute to an improvement of the stress-corrosion cracking (SCC) resistance while maintaining the T8 temper mechanical properties.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. Aluminum and Aluminum Alloys, ASM Specialty Handbook, J.R. Davis, ed., ASM INTERNATIONAL, TMS, Materials Park, OH, 1998, pp. 121–42.
2. E.J. Lavernia, T.S. Srivatsan, and F.A. Mohamed: J. Mater. Sci., 1990, vol. 25, pp. 1137–58.10.1007/BF00585420 ↗
3. K.K. Sankaran and N.J Grant: Aluminum Lithium 1, Proc 1st Int. Conf. Aluminum Lithium Alloys, T.H. Sanders, Jr. and E.A. Starke, Jr., eds., TMS, Warrendale, PA, 1981, pp. 205–27.
4. P.J. Gregson and H.M. Flower: Proc. Int. Conf. on Aluminum Technology ’86, T. Sheppard, ed., The Institute of Metals, London, 1986, pp. 423–28.
5. P.J. Gregson, H.M. Flower, C.N.J. Tite, and A.K. Mukhopadhyay: Mater. Sci. Technol., 1986, vol. 2, pp. 349–53.10.1179/mst.1986.2.4.349 ↗
6. W.S. Miller, J. White, and D.J. Lloyd: Aluminum Lithium Alloys IV, Proc. 4th Int. Conf. on Aluminum Lithium Alloys, G. Champier, B. Dubost, D. Miannay, and L. Sabetay, eds.; J. Phys., 1987, vol. 48, Suppl., pp. C3:131–C3:149.10.1051/jphyscol:1987317 ↗
7. R.C. Dorward and K.R. Hasse: Corr.—NACE, 1987, vol. 43, pp. 408–23.10.5006/1.3583877 ↗
8. N.J.H. Holroyd, A. Gray, G.M. Scamans, and R. Hermann: Aluminum Lithium Alloys III, Proc. 3rd Int. Conf. on Aluminum Lithium Alloys, C. Baker, P.J. Gregson, S.J. Harris and C.J. Peel, eds., The Institute of Metals, London, 1986, pp. 310–20.
9. F. Binsfeld, M. Habashi, J. Galland, J.P. Fidelle, D. Minnay, and P. Rofidal: Aluminum Lithium Alloys IV, Proc. 4th Int. Conf. on Aluminum Lithium Alloys, G. Champier, B. Dubost, D. Miannay, and L. Sabetay, eds., J. Phys., 1987, vol. 48, Suppl., pp. C3:587–C3:596.10.1051/jphyscol:1987368 ↗
10. B. Cina: United States Patent No. 3,856,584, Dec. 24, 1974.
11. B. Cina and B. Ranish: Paper No. XXV, Aluminum Industrial Products, ASM, Pittsburgh, PA, 1974.
12. K. Ural: J. Mater. Sci. Lett., 1984, vol. 13, pp. 383–85.10.1007/BF00420806 ↗
13. N.C. Danh, K. Rajan, and W. Wallace: Metall. Trans. A, 1983, vol. 14A, pp. 1843–50.10.1007/BF02645554 ↗
14. M. Kanno, I. Araki, and Q. Cui: Mater. Sci. Technol., 1994, vol. 10, pp. 599–603.10.1179/mst.1994.10.7.599 ↗
15. K. Rajan, W. Wallace, and J.C. Beddoes: J. Mater. Sci., 1982, vol. 17, pp. 2817–24.10.1007/BF00644656 ↗
16. M. Talianker and B. Cina: Metall. Trans. A, 1989, vol. 20A, pp. 2087–92.10.1007/BF02650294 ↗
17. C. Thakur and R. Balasubramaniam: Acta Mater., 1997, vol. 45, pp. 1323–32.10.1016/S1359-6454(96)00287-X ↗
18. J.K. Park: Mater. Sci. Eng., 1998, vol. A103, pp. 223–31.
19. M.B. Hall and J.W. Martin: Z. Metallkd, 1994, vol. 85, pp. 134–39.
20. M.U. Islam and W. Wallace: Metals Technol., 1983, vol. 10, pp. 386–92.10.1179/030716983803291893 ↗
21. M.U. Islam and W. Wallace: Metals Technol., 1984, vol. 11, pp. 320–22.10.1179/030716984803274594 ↗
22. M. Ahmad: Mater. Sci. Eng., 1990, vol. A125, pp. 1–14.10.1016/0921-5093(90)90246-Y ↗
23. J.S. Robinson: Mater. Sci. Forum, 2000, vols. 331–337, pp. 1653–58.10.4028/www.scientific.net/MSF.331-337.1653 ↗
24. A. Gray, N.J.H. Holroyd, and J. White: Aluminum Lithium Alloys V, Proc. 5th Int. Conf. on Aluminum Lithium Alloys, T.H. Sanders, Jr., and E.A. Starke, Jr., eds., Materials and Component Engineering Publications, Warrendale, PA, 1989, pp. 1175–86.
25. V. Komisarov, M. Tlianker, and B. Cina: Mater. Sci. Eng, 1996, vol. A221, pp. 113–21.10.1016/S0921-5093(96)10502-5 ↗
26. V. Komisarov, M. Tlianker, and B. Cina: Mater. Sci. Eng., 1989, vol. A242, pp. 39–49.
27. Z.Q. Hu, Y. Zhang, Y.L. Liu, and Z.Y. Zhu: Corrosion, 1993, vol. 49, pp. 491–98.10.5006/1.3316078 ↗
28. S. Fox, H.M. Flower, and D.C. McDarmaid: Aluminum Lithium Alloys III, Proc. 3rd Int. Conf. on Aluminum Lithium Alloys, C. Baker, P.J. Gregson, S.J. Harris, and C.J. Peel, eds., The Institute of Metals, London, 1986, pp. 263–72.
29. O. Jensrud and N. Ryum: Mater. Sci. Eng., 1984, vol. 64, pp. 229–36.10.1016/0025-5416(84)90106-X ↗
30. E.E. Underwood: in Quantitative Stereology, M. Cohen, ed., Addison Wesley, Reading, MA, 1970, p. 178.
31. N. Tryum: Acta Metall., 1969, vol. 17, p. 269.10.1016/0001-6160(69)90067-4 ↗
32. H.M. Flower and P.J. Gregson: Mater. Sci. Technol., 1987, vol. 3, pp. 81–90.10.1179/mst.1987.3.2.81 ↗
33. N. Nes: Acta Metall., 1972, vol. 20, p. 499.10.1016/0001-6160(72)90005-3 ↗
34. P.J. Gregson and H.M. Flower: J. Mater. Sci. Lett., 1984, vol. 3, pp. 829–34.10.1007/BF00727987 ↗
35. F.W. Gayle and J.B. Vandersande: Scripta Metall., 1984, vol. 18, pp. 473–78.10.1016/0036-9748(84)90424-1 ↗
36. F.W. Gayle and J.B. Vandersande: Proc. Conf. Aluminum Alloys—Their Physical and Mechanical Properties, E.A Starke and T.H. Sanders, eds., Engineering Materials Advisory Service, Warley, 1986, vol. II, p. 727.
37. K.S. Ghosh, K. Das, and U.K. Chatterjee: Mater. Sci. Technol., 2004, vol. 20, pp. 825–34.10.1179/026708304225019650 ↗
38. A. Luo, D.J. Lloyd, A. Gupta, and W.V. Youdelis: Acta Metall. Mater., 1993, vol. 41, pp. 769–76.10.1016/0956-7151(93)90009-H ↗
39. M.L. Starink and P.J. Gregson: Scripta Metall., 1995, vol. 33, pp. 893–900.10.1016/0956-716X(95)00317-O ↗
40. A.K. Mukherjee, C.N.J. Tite, H.M. Flower, P.J. Gregson, and F. Sale: Aluminum Lithium Alloys IV, Proc. 4th Int. Conf. on Aluminum Lithium Alloys, G. Champier, B. Dubost, D. Miannay, and L. Sabetay, eds., J. Phys., 1987, vol. 48, Suppl., pp. C3:439–C3:446.10.1051/jphyscol:1987350 ↗
41. G.M. Reddy, A.A. Gokhale, and K. Prasad Rao: Sci. Technol. Welding Joining, 1998, vol. 3, pp. 151–58.10.1179/stw.1998.3.3.151 ↗
42. R.E. Ricker, J.L. Fink, and A.K. Vasudevan: Metall. Trans. A, 1991, vol. 22A, pp. 264–67.10.1007/BF03350971 ↗
43. C.P. Blankenship, Jr. and E.A. Starke: Metall. Trans. A, 1993, vol. 22A, pp. 833–41.10.1007/BF02656504 ↗
44. T.S. Srivatsan and T. Allan Place: J. Mater. Sci., 1989, vol. 2, pp. 1543–51.10.1007/BF01105669 ↗
45. I.J. Lavernia, T.S. Srivatsan, and F.A. Mohamed: J. Mater. Sci., 1990, vol. 25, pp. 1137–58.10.1007/BF00585420 ↗
46. A. Gray: Aluminum Lithium Alloys IV, Proc. 4th Int. Conf. on Aluminum Lithium Alloys, G. Champier, B. Dubost, D. Miannay, and L. Sabetay, eds., J. Phys., 1987, vol. 48, Suppl., pp. C3:891–C3:904.10.1051/jphyscol:19873104 ↗
47. J.M. Sater and T.H. Sanders: Aluminum Lithium Alloys V, Proc. 5th Int. Conf. on Aluminum Lithium Alloys, T.H. Sanders, Jr. and E.A. Starke, Jr., eds., Materials and Component Engineering Publications, Warrendale, PA, 1989, pp. 1217–25.
48. M. Reboul and P Meyer: Aluminum Lithium Alloys IV, Proc. 4th Int. Conf. on Aluminum Lithium Alloys, G. Champier, B. Dubost, D. Miannay, and L. Sabetay, eds., J. Phys., 1987, vol. 48, Suppl., pp. C3:881–C3:889.10.1051/jphyscol:19873103 ↗
49. J. Garcia, P. Ponthiaux, M. Habashi, and J. Galland: Aluminum Lithium Alloys IV, Proc. 4th Int. Conf. on Aluminum Lithium Alloys, G. Champier, B. Dubost, D. Miannay, and L. Sabetay, eds., J. Phys., 1987, vol. 48, Suppl., pp. C3:861–C3:870.10.1051/jphyscol:19873101 ↗
50. B. Bavarian, J. Becker, S.N. Parikh, and M. Zamanzadeh: Aluminum Lithium Alloys V, Proc. 5th Int. Conf. on Aluminum Lithium Alloys, T.H. Sanders, Jr. and E.A. Starke, Jr., eds., Materials and Component Engineering Publications, Warrendale, PA, 1989, pp. 1227–36.