Effects of volume fraction of tempered martensite on dynamic deformation properties of a Ti-6Al-4V alloy having a bimodal microstructure
Source abstract
Abstract
The effects of the volume fraction of tempered martensite on the tensile and dynamic deformation properties of a Ti-6Al-4V alloy having a bimodal microstructure were investigated in this study. Five microstructures having various tempered-martensite volume fractions were obtained by varying heat-treatment conditions. Dynamic torsional tests were conducted on them using a torsional Kolsky bar. The test data were analyzed in relation to microstructures, tensile properties, and adiabatic shear-band formation. Under a dynamic loading condition, the maximum shear stress increased with increasing tempered-martensite volume fraction, whereas the fracture shear strain decreased. Observation of the deformed area after the dynamic torsional test indicated that a number of voids initiated mainly at α-phase/tempered-martensite interfaces, and that the number of voids increased with increasing martensite volume fraction. Adiabatic shear bands of 6 to 10 μm in width were formed in the specimens having lower martensite volume fractions, while they were not formed in those having higher martensite volume fractions. The possibility of adiabatic shear-band formation was explained by concepts of absorbed deformation energy and void initiation.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Titanium Alloys Microstructure and Properties · Surface Treatment and Residual Stress
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. M.A. Greenfield and H. Margolin: Metall. Trans. A, 1972, vol. 3A, pp. 2649–59.10.1007/BF02644241 ↗
2. D. Eylon, J.A. Hall, C.M. Pierce, and D.L. Ruckel: Metall. Trans. A, 1976, vol. 7A, pp. 1817–26.10.1007/BF02659811 ↗
3. A. Gysler and G. Lutjering: Metall. Trans. A, 1982, vol. 13A, pp. 1435–43.10.1007/BF02642882 ↗
4. W. Lee and C. Lin: Mater. Sci. Eng., 1998, vol. A241, pp. 48–59.10.1016/S0921-5093(97)00471-1 ↗
5. S.L. Semiatin and T.R. Bieler: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1871–75.10.1007/s11661-001-0166-y ↗
6. D.-G. Lee, S. Lee, C.S. Lee, and S. Hur: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2541–48.10.1007/s11661-003-0013-4 ↗
7. S.P. Timothy and I.M. Hutchings: Acta Metall., 1985, vol. 33, pp. 667–76.10.1016/0001-6160(85)90030-6 ↗
8. H.T. Li, Y.M. Zhang, and D.Z. Yang: Mater. Sci. Eng., 2000, vol. A292, pp. 130–32.10.1016/S0921-5093(00)01019-4 ↗
9. Q. Xue, M.A. Meyers, and V.F. Nesterenko: Acta Mater., 2002, vol. 50, pp. 575–96.10.1016/S1359-6454(01)00356-1 ↗
10. D.-G. Lee, S. Lee, and C.S. Lee: Mater. Sci. Eng. A, 2004, vol. A366, pp. 25–37.10.1016/j.msea.2003.08.061 ↗
11. M.-H. Lee, D.-J. Yoon, D.-H. Won, T.-S. Bae, and F. Watari: Met. Mater. Int., 2003, vol. 9, pp. 35–42.10.1007/BF03027227 ↗
12. F.S. Lin, E.A. Starke, Jr., S.B. Chakrabortty, and G. Gysler: Metall. Trans. A, 1984, vol. 15A, pp. 1229–46.10.1007/BF02644717 ↗
13. D.-G. Lee, S. Kim, S. Lee, and C.S. Lee: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 315–24.10.1007/s11661-001-0263-y ↗
14. D.-G. Lee, Y.H. Lee, S. Lee, C.S. Lee, and S. Hur: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 719–24.10.1007/s11661-004-0383-2 ↗
15. D.G. Lee, Y.H. Lee, S. Lee, C.S. Lee, J.-H. Choi, and S. Hur: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 3103–12.10.1007/s11661-004-0055-2 ↗
16. S.V. Kailas, Y.V.R.K. Prasad, and S.K. Biswas: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 2173–79.10.1007/BF02652318 ↗
17. M. Mier and A.K. Mukherjee: Scripta Metall., 1990, vol. 24, pp. 331–36.10.1016/0956-716X(90)90265-I ↗
18. S. Yadav and K.T. Ramesh: Mater. Sci. Eng., 1995, vol. A203, pp. 140–53.10.1016/0921-5093(95)09865-8 ↗
19. Metals Handbook, 9th ed., ASM, Metals Park, OH, 1990, vol. 8, pp. 218–24.
20. S.P. Timothy: Acta Metall., 1987, vol. 35, pp. 301–06.10.1016/0001-6160(87)90238-0 ↗
21. C.S. Kang, S.Y. Chang, and S.K. Hong: Met. Mater. Int., 2003, vol. 9, pp. 439–45.10.1007/BF03027148 ↗
22. C. Zener and J.H. Hollomon: J. Appl. Phys., 1944, vol. 15, pp. 22–32.10.1063/1.1707363 ↗
23. J.W. Hutchinson: Scripta Metall., 1984, vol. 18, pp. 421–22.10.1016/0036-9748(84)90414-9 ↗
24. H.A. Grebe, H.-R. Pak, and M.A. Meyers: Metall. Trans. A, 1985, vol. 16A, pp. 761–75.10.1007/BF02814827 ↗
25. I.A. Akmoulin, M. Niinomi, and T. Kobayashi: Metall. Trans. A, 1994, vol. 25A, pp. 1655–66.10.1007/BF02668531 ↗
26. S. Liao and J. Duffy: J. Mech. Phys. Solids, 1998, vol. 46, pp. 2201–31.10.1016/S0022-5096(98)00044-1 ↗
27. S.P. Timothy and I.M. Hutchings: Acta Metall., 1985, vol. 33, pp. 667–76.10.1016/0001-6160(85)90030-6 ↗
28. Y. Me-Bar and D. Shechtman: Mater. Sci. Eng., 1983, vol. 58, pp. 181–88.10.1016/0025-5416(83)90044-7 ↗
29. M.A. Meyers and H.-R. Pak: Acta Metall., 1986, vol. 34, pp. 2493–99.10.1016/0001-6160(86)90152-5 ↗
30. M.C. Mataya, M.J. Carr, and G. Krauss: Metall. Trans. A, 1982, vol. 13A, pp. 1263–74.10.1007/BF02645510 ↗
31. M.A. Meyers, Y.B. Xu, Q. Xue, M.T. Perez-Prado, and T.R. McNelley: Acta Mater., 2003, vol. 51, pp. 1307–25.10.1016/S1359-6454(02)00526-8 ↗
32. K. Cho, S. Lee, S.R. Nutt, and J. Duffy: Acta Metall., 1993, vol. 41, pp. 923–32.10.1016/0956-7151(93)90026-O ↗
33. H.J. McQueen: in Hot Deformation of Aluminum Alloys, T.G. Langdon, ed., TMS, Warrendale, PA, 1991, pp. 31–38.
34. M.E. Backman and W. Goldsmith: Int. J. Eng. Sci., 1978, vol. 16, pp. 1–99.10.1016/0020-7225(78)90002-2 ↗
35. C.L. Wittman, M.A. Meyers, and H.-R. Pak: Metall. Trans. A, 1990, vol. 21A, pp. 707–16.10.1007/BF02671941 ↗
36. K. Minnaar and M. Zhou: J. Mech. Phys. Solids, 1998, vol. 46, pp. 2155–70.10.1016/S0022-5096(98)00020-9 ↗
37. M.A. Meyers and C.L. Wittman: Metall. Mater. Trans. A, 1990, vol. 21A, pp. 3153–64.10.1007/BF02647311 ↗