journal article·2005-02Open access

Dynamic deformation behavior of ultrafine-grained low-carbon steels fabricated by equal-channel angular pressing

Byoungchul Hwang, Yang Gon Kim, Han Sang Lee, Sunghak Lee, Byoung Doo Ahn, Dong Hyuk Shin, Chang Gil Lee

Abstract

The dynamic deformation behavior of ultrafine-grained low-carbon steels fabricated by equal-channel angular pressing (ECAP) was investigated in this study. Dynamic torsional tests, using a torsional Kolsky bar, were conducted on four steel specimens, two of which were annealed at 480 °C after ECAP, and then the test data were compared in terms of microstructures, tensile properties, and adiabatic shear-band formation. The equal-channel angular pressed specimen consisted of very fine, equiaxed grains of 0.2 to 0.3 µm in size, which were slightly coarsened after annealing. The dynamic torsional test results indicated that maximum shear stress decreased with increasing annealing time, whereas fracture shear strain increased. Some adiabatic shear bands were observed at the gage center of the dynamically deformed torsional specimen. Their width was smaller in the equal-channel angular pressed specimen than in the 1-hour-annealed specimen, but they were not found in the 24-hour-annealed specimen. Ultrafine, equiaxed grains of 0.05 to 0.2 µm in size were formed inside the adiabatic shear band, and their boundaries had characteristics of high-angle grain boundaries. These phenomena were explained by dynamic recrystallization due to a highly localized plastic strain and temperature rise during dynamic deformation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · High-Velocity Impact and Material Behavior · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. R.Z. Valiev, N.A. Krasilnikov, and N.K. Tsenev: Mater. Sci. Eng. A, 1991, vol. 137, pp. 35–40.10.1016/0921-5093(91)90316-F ↗
2. V.M. Segal: Mater. Sci. Eng. A, 1995, vol. 197, pp. 157–64.10.1016/0921-5093(95)09705-8 ↗
3. J.C. Lee, H.K. Seok, and J.Y. Suh: Acta Mater., 2002, vol. 50, pp. 4005–19.10.1016/S1359-6454(02)00200-8 ↗
4. Y. Saito, H. Utsunomiya, N. Tsuji, and T. Sakai: Acta Mater., 1999, vol. 47, pp. 579–83.10.1016/S1359-6454(98)00365-6 ↗
5. N.A. Akhmadeev, N.P. Kobelev, R.R. Mulyukov, Y.M. Soifer, and R.Z. Valiev: Acta Metall. Mater., 1993, vol. 41, pp. 1041–46.10.1016/0956-7151(93)90153-J ↗
6. M.V. Markushev, C.C. Bampton, M. Yu. Murashkin, and D.A. Hardwick: Mater. Sci. Eng. A, 1997, vol. A234–A236, pp. 927–31.10.1016/S0921-5093(97)00333-X ↗
7. K.T. Park, Y.S. Kim, J.G. Lee, and D.H. Shin: Mater. Sci. Eng. A, 2000, vol. A293, pp. 165–72.10.1016/S0921-5093(00)01220-X ↗
8. M. Furukawa, Z. Horita, and T.G. Langdon: Met. Mater. Int., 2003, vol. 9, pp. 141–49.10.1007/BF03027270 ↗
9. D.H. Shin, I. Kim, and J. Kim: Met. Mater. Int., 2002, vol. 8, pp. 513–18.10.1007/BF03178251 ↗
10. I.V. Alexandrov, A.A. Dubravin, A.R. Kilmametov, V.U. Kazykhanov, and R.Z. Valiev: Met. Mater. Int., 2003, vol. 9, pp. 151–56.10.1007/BF03027271 ↗
11. S. Lee, D. Kwon, Y.K. Lee, and O. Kwon: Metall. Trans. A, 1995, vol. 26A, pp. 1093–100.10.1007/BF02670605 ↗
12. D. Jia, K.T. Ramesh, and E. Ma: Acta Mater., 2003, vol. 51, pp. 3495–3509.10.1016/S1359-6454(03)00169-1 ↗
13. Q. Wei, L. Kecskes, T. Jiao, K.T. Hartwig, K.T. Ramesh, and E. Ma: Acta Mater., 2004, vol. 52, pp. 1859–69.10.1016/j.actamat.2003.12.025 ↗
14. Q. Wei, T. Jiao, S.N. Mathaudhu, E. Ma, K.T. Hartwig, and K.T. Ramesh: Mater. Sci. Eng. A, 2003, vol. A358, pp. 266–72.10.1016/S0921-5093(03)00305-8 ↗
15. M.A. Meyers: Dynamic Behavior of Materials, John Wiley & Sons, New York, NY, 1994.10.1002/9780470172278 ↗
16. D.K. Kim, S.Y. Kang, S. Lee, and K.J. Lee: Metall. Trans. A, 1999, vol. 30A, pp. 81–92.10.1007/s11661-999-0197-3 ↗
17. H.S. Lee, B. Hwang, S. Lee, C.G. Lee, and S.J. Kim: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2371–82.10.1007/s11661-006-0217-5 ↗
18. K.M. Cho, S. Lee, S.R. Nutt, and J. Duffy: Acta Mater., 1993, vol. 41, pp. 923–32.10.1016/0956-7151(93)90026-O ↗
19. Y. Bai, and B. Dodd: Adiabatic Shear Localization—Occurrence, Theories and Applications, Pergamon Press, Eimsford, NJ, 1992.
20. W.S. Jenong, S.M. Kim, H.G. Park, B.L. Jang, and D.H. Shin: J. Kor. Inst. Met. Mater., 2001, vol. 39, pp. 1198–1204.
21. S.P. Timothy and I.M. Hutching: Acta Metall., 1985, vol. 33, pp. 667–76.10.1016/0001-6160(85)90030-6 ↗
22. C.L. Wittman, M.A. Meyers, and H.-R. Pak: Metall. Trans. A, 1990, vol. 21A, pp. 707–16.10.1007/BF02671941 ↗
23. J.H. Beatty, L.W. Meyers, M.A. Meyers, and S. Nemat-Nasser: U.S. Army Materials Technical Laboratory Report, MTL TR 90-54, Champaign, IL, Sept. 1991.
24. M.A. Meyer and H.-R. Pak: Acta Metall., 1986, vol. 34, pp. 2493–99.10.1016/0001-6160(86)90152-5 ↗
25. M. Hartherly and A.S. Malin: Scripta Metall., 1983, vol. 18, pp. 449–54.10.1016/0036-9748(84)90419-8 ↗
26. M.A. Meyers, Y.B. Xu, Q. Xue, M.T. Perez-Prado, and T.R. McNelley: Acta Mater., 2003, vol. 51, pp. 1307–25.10.1016/S1359-6454(02)00526-8 ↗
27. H.C. Rogers: Ann. Rev. Mater. Sci., 1979, vol. 9, pp. 283–311.10.1146/annurev.ms.09.080179.001435 ↗
28. J.D. Derep: Acta Metall., 1987, vol. 35, pp. 1245–49.10.1016/0001-6160(87)90005-8 ↗
29. A.S. Malin and W.Y. Yeung: Mater. Forum. 1988, vol. 11, pp. 111–16.
30. H. Yada, Y. Matsumura, and T. Senuma: in Int. Conf. on Physical Metallurgy of Thermomechanical Processing of Steels and Other Metals, I. Tamura, ed., JISI, Tokyo, 1988, pp. 200–07.
31. Y. Matsumura and H. Yada: Trans. Iron Steel Inst. Jpn., 1987, vol. 27, pp. 492–98.10.2355/isijinternational1966.27.492 ↗
32. K.T. Park and D.H. Shin: Mater. Sci. Eng., 2002, vol. A334, pp. 79–86.10.1016/S0921-5093(01)01796-8 ↗
33. W.Q. Cao, A. Godfrey, W. Liu, and Q. Liu: Mater. Sci. Eng., 2003, vol. A360, pp. 420–25.10.1016/S0921-5093(03)00508-2 ↗