journal article·2000-03

Mechanical behavior of a fine-grained duplex γ-TiAl alloy

Z. Jin, C. Cady, G. T. Gray, Y. -W. Kim

Publisher page

Abstract

The mechanical behavior of a fine-grained duplex γ-TiAl alloy was studied in compression at strain rates ranging from 0.001 to 2000 s−1 and temperatures from −196°C to 1200°C. The temperature dependence of the yield and flow stresses is found to depend on the strain rate. At strain rates of 0.001 and 0.1 s−1, the yield stress decreases as the temperature increases, with a plateau between 600°C and 800°C. At strain rates of 35 and 2000 s−1, the yield stress exhibits a positive temperature dependence at temperatures above 600°C; however, postyield flow stresses exhibit a reduced temperature dependency. The work-hardening rate decreases dramatically with temperature at low and high temperatures, with a plateau occurring at intermediate temperatures for all strain rates. The work-hardening-rate plateau is seen to extend to higher temperatures as the strain rate increases. The strain-rate sensitivity at strain rates of 0.1 s−1 and greater is lower than 0.1, although it increases slightly with temperature. At 0.001 s−1, the strain-rate sensitivity increases dramatically at high temperatures (equal to 4.5 at 1200°C). The anomalous (positive) temperature dependence of the yield stress at high strain rates (>1 s−1) and high temperatures (>600°C) is explained via a dislocation-jog pinning mechanism. The negative temperature dependence of the yield stress at low strain rates (<1 s−1) and high temperatures (>900°C) is though to be due to a thermally activated dislocation-jog climb process in the grain interiors and/or deformation and recovery processes at/near grain boundaries. The decreased anomalous temperature dependence of the flow stress at high strain rates and high temperatures is ascribed to dynamic recovery promoted by adiabatic heating.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (63)

Show source-provided references
1. Y.-W. Kim and D.M. Dimiduk: JOM, 1991, vol. 43, pp. 40–47.10.1007/BF03221103 ↗
2. Y.-W. Kim: JOM, 1994, vol. 46, pp. 30–39.10.1007/BF03220745 ↗
3. M. Yamaguchi and H. Inui: in Structural Intermetallics, R. Darolia, J.J. Lewandowski, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathal, eds., TMS, Warrendale, PA, 1993, pp. 127–42.
4. C.M. Austin and T.J. Kelly: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 21–32.
5. S.E. Hartfield-Wunsch, A.A. Sperling, R.S. Morrison, W.E. Dowling, Jr., and J.E. Allison: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds, TMS, Warrendale, PA, 1995, pp. 41–52.
6. Y.-W. Kim: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 637–54.
7. H.A. Lipsitt, D. Shechtman, and R.E. Schafrik: Metall. Trans. A, 1975, vol. 6A, pp. 1991–96.10.1007/BF03161822 ↗
8. T. Kawabata, T. Kanai, and O. Izumi: Acta Metall., 1985, vol. 33, pp. 1355–66.10.1016/0001-6160(85)90245-7 ↗
9. S.C. Huang: Scripta Metall., 1988, vol. 22, pp. 1885–88.10.1016/S0036-9748(88)80231-X ↗
10. T. Kawabata, T. Abumiya, T. Kanai, and O. Izumi: Acta Metall., 1990, vol. 38, pp. 1381–93.10.1016/0956-7151(90)90106-Q ↗
11. S.H. Whang and Y.D. Hahn: Scripta Metall., 1990, vol. 24, pp. 485–90.10.1016/0956-716X(90)90187-L ↗
12. Y.-W. Kim: Mater. Sci. Eng., 1995, vol. A192, pp. 519–33.10.1016/0921-5093(94)03271-8 ↗
13. W. Wunderlich, T. Kremser, and G. Frommeyer: Z. Metallkd, 1990, vol. 81, pp. 802–08.
14. S.C. Huang and E.L. Hall: Scripta Metall., 1991, vol. 25, pp. 1805–09.10.1016/0956-716X(91)90308-N ↗
15. S.C. Huang and E.L. Hall: Metall. Trans. A, 1991, vol. 22A, pp. 427–39.10.1007/BF02656810 ↗
16. P.P. Rao and K. Tangri: Mater. Sci. Eng., 1991, vol. A132, pp. 49–59.10.1016/0921-5093(91)90360-Y ↗
17. T. Kawabata, T. Abumiya, and O., Izumi: Acta Metall., 1992, vol. 40, pp. 2557–67.10.1016/0956-7151(92)90325-9 ↗
18. Y.-W. Kim: Acta Metall., 1992, vol. 40, pp. 1121–34.10.1016/0956-7151(92)90411-7 ↗
19. M.A. Morris: Phil. Mag. A. 1994, vol. 69, pp. 129–50.10.1080/01418619408242214 ↗
20. M. Nazmy and M. Staubli: Scripta Metall., 1994, vol. 31, pp. 829–33.10.1016/0956-716X(94)90487-1 ↗
21. D.G. Morris, S. Gunter, and M. Leboeuf: Phil. Mag. A., 1994, vol. 69, pp. 527–50.10.1080/01418619408242228 ↗
22. W.R. Chen, B. Zhang, W.J. Chen, J. Wang, and X. Wan: Scripta Metall., 1994, vol. 31, pp. 1297–1300.10.1016/0956-716X(94)90106-6 ↗
23. C.M. Sabinash, S.M.L. Sastry, and K.L. Jerina: Scripta Metall., 1994, vol. 30, pp. 1391–96.10.1016/0956-716X(94)90234-8 ↗
24. B. Viguier, K.J. Hemker, J. Bonneville, F. Louchet, and J.-L. Martin: Phil. Mag. A, 1995, vol. 71, pp. 1295–1312.10.1080/01418619508244375 ↗
25. F. Louchet and B. Viguier: Phil. Mag. A, 1995, vol. 71, pp. 1313–33.10.1080/01418619508244376 ↗
26. S. Sriram, V.K. Vasudevan, and D.M. Dimiduk: Mater. Sci. Eng., 1995, vols. A192-A193, pp. 217–25.10.1016/0921-5093(94)03250-5 ↗
27. A. Bartels, C. Koeppe, T. Zhang, and H. Mecking: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 655–63.
28. D. Schechtman, M.J. Blackburn, and H.A. Lipsitt: Metall. Trans., 1974, vol. 5, pp. 1374–81.
29. G. Hug, A. Loiseau, and A. Lasalmonie: Phil. Mag. A, 1986, vol. 54, pp. 47–65.10.1080/01418618608242882 ↗
30. G. Hug, A. Loiseau, and P. Veyssiere: Phil. Mag. A, 1988, vol. 57, pp. 499–523.10.1080/01418618808204682 ↗
31. S.A. Court, V.K. Vasudevan, and H.L. Fraser: Phil. Mag. A, 1990, vol. 61, pp. 141–58.10.1080/01418619008235562 ↗
32. E.L. Hall and S.C. Huang: Acta Metall., 1990, vol. 38, pp. 539–49.10.1016/0956-7151(90)90208-X ↗
33. B.A. Greenberg, O.V. Antonova, L.E. Karkina, A.B. Notkin, and M.V. Ponomarev: Acta Metall., 1992, vol. 40, pp. 815–22.10.1016/0956-7151(92)90023-8 ↗
34. B.A. Greenberg, O.V. Antonova, V.N. Indenbaum, L.E. Karkina, A.B. Notkin, M.V. Ponomarev, and L.V. Smirnov Acta Metall., 1991, vol. 39, pp. 233–42.10.1016/0956-7151(91)90271-2 ↗
35. V.K. Vasudevan, M.A. Stucke, S.A. Court, and H.L. Fraser: Phil. Mag. Lett., 1989, vol. 59, pp. 299–307.10.1080/09500838908206358 ↗
36. M.A. Morris: Phil. Mag. A, 1993, vol. 68, pp. 237–57.10.1080/01418619308221203 ↗
37. M.A. Morris: Phil. Mag. A, 1993, vol. 68, pp. 259–78.10.1080/01418619308221204 ↗
38. J. Luster and M.A. Morris: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1745–56.10.1007/BF02670762 ↗
39. F. Appel and R. Wagner: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 231–44.
40. B. Viguier, M. Cieslar, K.J. Hemker, and J.L. Martin: High-Temperature Ordered Intermetallic Alloys VI, Materials Research Society Symposia Proceedings, J.A. Horton, I Baker, S. Hanada, R.D. Noebe, and D.S. Schwartz, eds., Materials Research Society, Pittsburgh, PA, 1995, vol. 364, pp. 653–58.
41. T. Fujiwara, A. Nakamura, M. Hosomi, S.R. Nishitani, Y. Shirai, and M. Yamaguchi: Phil. Mag. A, 1990, vol. 61, pp. 591–606.10.1080/01418619008231937 ↗
42. H. Inui, A. Nakamura, M.H. Oh, and M. Yamaguchi: Phil. Mag. A, 1992, vol. 66, pp. 557–73.10.1080/01418619208201575 ↗
43. H. Inui, M.H. Oh, A. Nakamura, and M. Yamaguchi: Acta Metall., 1992, vol. 40, pp. 3095–3104.10.1016/0956-7151(92)90472-Q ↗
44. Y. Umakoshi, T. Nakano, and T. Yamane: Mater. Sci. Eng., 1992, vol. A152, pp. 81–88.10.1016/0921-5093(92)90050-B ↗
45. H. Inui, K. Kishida, M. Misaki, M. Kobayashi, Y. Shirai, and M. Yamaguchi: Phil. Mag. A, 1995, vol. 72, pp. 1609–31.10.1080/01418619508243933 ↗
46. H.Y. Yasuda, T. Nakano, and Y. Umakoshi: Phil. Mag. A, 1996, vol. 73, pp. 1035–51.10.1080/01418619608243702 ↗
47. H.Y. Yasuda, T. Nakano, and Y. Umakoshi: Phil. Mag. A, 1996, vol. 73, pp. 1053–67.10.1080/01418619608243703 ↗
48. G.T. Gray III: in Microstructure/Property Relationships in Titanium Aluminides and Alloys, Y.-W. Kim and R.R. Boyer, eds., TMS, Warrendale, PA, 1991, pp. 263–74.
49. S.A. Maloy and G.T. Gray III: Acta Metall., 1996, vol. 44, pp. 1741–56.
50. Z. Jin, C. Cady, G.T. Gray III, and Y.-W. Kim: in Deformation and Fracture of Ordered Intermetallic Materials, W.O. Soboyejo, T.S. Srivatsan, and H.L. Fraser, eds., TMS, Warrendale, PA, 1996, pp. 101–10.
51. P.S. Follansbee: The Metals Handbook, 9th ed., ASM, Metals Park, OH, 1985, vol. 8, pp. 198–203.
52. R.E. Schafrik: Metall. Trans. A, 1977, vol. 8A, pp. 1003–06.10.1007/BF02661586 ↗
53. P.B. Hirsch and T.E. Mitchell: Can. J. Phys., 1967, vol. 45, pp. 663–706.10.1139/p67-054 ↗
54. H. Mecking: Work Hardening in Tension and Fatigue A.W. Thompson, ed., ASME, New York, NY, 1977, pp. 67–88.
55. J.W. Edington, K.N. Melton, and C.P. Cutler: Progr. Mater. Sci., 1976, vol. 21, pp. 61–158.10.1016/0079-6425(76)90005-0 ↗
56. R.M. Imayev, O.A. Kaybyshey, and G.A. Salishchev: Phys. Met. Metallogr., 1990, vol. 70 pp. 179–86.
57. S.C. Cheng, J. Wolfenstine, and O.D. Sherby: Metall. Trans. A, 1992, vol. 23A, pp. 1509–13.10.1007/BF02647333 ↗
58. R.M. Imayev, V.M. Imayev, and G.A. Salishchev: J. Mater. Sci., 1992, vol. 27, pp. 4465–71.10.1007/BF00541580 ↗
59. T. Tsuzuku and H. Sato: J. Phys. IV, 1993, vol. 3, pp. 389–95.10.1051/jp4:1993761 ↗
60. H.S. Yang, W.B. Lee, and A.K. Mukherjee: in Structural Intermetallics, R. Darolia, J.J. Lewandowski, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathal, eds., TMS, Warrendale, PA, 1993, pp. 69–76.
61. Z. Jin, G.T. Gray III, and M. Yamaguchi: Phil. Mag. A, 2000, vol. 80, pp. 49–68.
62. Z. Jin, G.T. Gray III, and Y.-W. Kim: Mater. Sci. Eng. A, 1997, vols. A239-A240, pp. 729–35.10.1016/S0921-5093(97)00659-X ↗
63. S.L. Semiatin, N. Frey, S.M. El-Soudani, and J.D. Bryant: Metall. Trans. A, 1992, vol. 23A, pp. 1719–35.10.1007/BF02804366 ↗