Effect of surface modification of high-density polyethylene by direct current and radio frequency glow discharge on wetting and adhesion characteristics
Source abstract
Abstract
The present investigation aims to optimize the process parameters of Direct Current (DC) and Radio Frequency (RF) glow discharge treatment through air in terms of discharge power and time of exposure for the surface modification of high-density polyethylene (HDPE) sheet, for attaining best adhesive joint of the polymer to mild steel. In order to estimate the extent of surface modification, the surface energies of the polymer surfaces exposed to glow discharge have been determined by measuring contact angles using two standard test liquids of known surface energies. It is observed that at a given power level of DC glow discharge, surface energy and its polar component increase with increasing exposure time, attaining a maximum and then decreasing. In the case of RF glow discharge, surface energy and its polar component increase with increasing exposure time and then saturate. Surface modification by DC glow discharge increases the surface energy of HDPE relatively more at a lower power compared to that observed for RF glow discharge. The dispersion component of surface energy remains almost unaffected. The surfaces have also been studied by electron spectroscopy for chemical analysis (ESCA) and energy-dispersive spectra (EDS). A significant oxygen peak is observed for surface-modified polymer as detected by ESCA and EDS. Lap shear tensile test of an adhesive (Araldite AY 105) joint of HDPE with mild steel has been carried out in optimizing the parameters of DC and RF glow discharge for maximum joint strength. When HDPE is exposed to DC glow discharge, improvement of adhesive joint strength of HDPE to mild steel is found to be by a factor more than 7. On the other hand, when HDPE is exposed to RF glow discharge, results in improvement of adhesive joint strength of HDPE to mild steel by a factor nearer to 7 are found. Thus, DC glow discharge is more capable for increasing wetting and adhesion characteristics of the polymer.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Modification and Superhydrophobicity · Advanced Sensor and Energy Harvesting Materials · High voltage insulation and dielectric phenomena
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. G. Akovali, Z.M.O. Rzaev, and D.H. Mamedov: J. Appl. Polymer Sci., 1995, vol. 58, pp. 645–51.10.1002/app.1995.070580319 ↗
2. D.S. Bag, V.P. Kumar, and S. Maiti: J. Appl. Polymer Sci., 1999, vol. 71, pp. 1041–48.10.1002/(SICI)1097-4628(19990214)71:7<1041::AID-APP1>3.0.CO;2-R ↗
3. J. Behnisch, A. Hollander, and H. Zimmermann: J. Appl. Polymer Sci., 1993, vol. 49, pp. 117–24.10.1002/app.1993.070490114 ↗
4. S. Bhowmik, P.K. Ghosh, S. Ray, and S.K. Barthwal: J. Adhesion Sci. Technol., 1998, vol. 12 (11), pp. 1181–204.10.1163/156856198X00380 ↗
5. S. Bhowmik, P.K. Ghosh, and S. Ray: 2nd Int. Symp. on Polymer Surface Modification: Relevance to Adhesion, Newark, NJ, May 24–26, 1999.
6. S. Bhowmik, P.K. Ghosh, and S. Ray: J. Appl. Polymer Sci., 2001, vol. 80, pp. 1140–49.10.1002/app.1197 ↗
7. C.M.G. Carlsson and K.S. Johansson: Surface Interface Analysis, 1993, vol. 20, pp. 441–48.10.1002/sia.740200518 ↗
8. P. Dalet, E. Papon, and J.J. Villenave: J. Adhesion Technol., 1999, vol. 13 (8), pp. 857–70.10.1163/156856199X00712 ↗
9. L. Dorn and W. Wahona: Welding and Cutting, 1990, vol. 42, pp. 506–09.
10. F.P. Epaillard, B. Chevet, and J.C. Brosse: J. Adhesion Sci. Technol., 1994, vol. 8 (4), pp. 455–68.10.1163/156856194X00339 ↗
11. J.F. Friedrich, P. Rohrer, W. Saur, T. Gross, A. Lippitz, and W. Unger: J. Surface Coating Technol., 1993, vol. 59, pp. 371–78.10.1016/0257-8972(93)90115-5 ↗
12. N. Gavrilov, D. Yakusheva, and A. Kondyurin: J. Appl. Polymer Sci., 1998, vol. 69, pp. 1071–77.10.1002/(SICI)1097-4628(19980808)69:6<1071::AID-APP3>3.0.CO;2-D ↗
13. B. Gupta, J. Hilborn, C. Hollenstein, C.J.G. Plummer, R. Houriet, and N. Xanthopoulos: J. Appl. Polymer Sci., 2000, vol. 78, pp. 1083–91.10.1002/1097-4628(20001031)78:5<1083::AID-APP170>3.0.CO;2-5 ↗
14. S. Ichikawa and H. Aral: SAE, J. Mater. Manufacturing, Sec. 5, 1991, vol. 100, pp. 28–36.
15. S.O. Kell, T. Henshaw, G. Farrow, M. Aindow, and C. Jones: Surface Interface Analysis, 1995, vol. 23, pp. 319–27.10.1002/sia.740230508 ↗
16. E.M. Liston, L. Martinu, and M.R. Wertheimer: J. Adhesion Sci. Technol., 1993, vol. 7 (10), pp. 1077–89.10.1163/156856193X00600 ↗
17. C.J. Rong, W.X. Yan, and W. Tomiji: J. Appl. Polymer Sci., 1999, vol. 72, pp. 1327–33.10.1002/(SICI)1097-4628(19990606)72:10<1327::AID-APP13>3.0.CO;2-0 ↗
18. P. Stark: SAE, J. Aerospace, Sec. 1, 1990, vol. 99, pp. 571–88.
19. M. Suzuki, A. Kishida, H. Iwata, and Y. Ikada: Macromolecules, 1986, vol. 19, p. 1804.10.1021/ma00161a005 ↗
20. Y. Yao, X. Liu, and Y. Zhu: J. Adhesion Sci. Technol., 1993, vol. 3 (3), pp. 63–75.
21. Y. Yao, X. Liu, and Y. Zhu: J. Appl. Polymer Sci., 1993, vol. 48, pp. 57–65.10.1002/app.1993.070480106 ↗