Optimization of the johnson-mehl-avarami equation parameters for α-ferrite to γ-austenite transformation in steel welds using a genetic algorithm
Source abstract
Abstract
A nonisothermal Johnson-Mehl-Avarami (JMA) equation with optimized JMA parameters is proposed to represent the kinetics of transformation of α-ferrite to γ-austenite during heating of 1005 steel. The procedure used to estimate the JMA parameters involved a combination of numerical heat-transfer and fluid-flow calculations, the JMA equation for nucleation and growth for nonisothermal systems, and a genetic algorithm (GA) based optimization tool that used a limited volume of experimental kinetic data. The experimental data used in the calculations consisted of phase fraction of γ-austenite measured at several different monitoring locations in the heat-affected zone (HAZ) of a gas tungsten arc (GTA) weld in 1005 steel. These data were obtained by an in-situ spatially resolved X-ray diffraction (SRXRD) technique using synchrotron radiation during welding. The thermal cycles necessary for the calculations were determined for each monitoring location from a well-tested three-dimensional heat-transfer and fluid-flow model. A parent centric recombination (PCX) based generalized generation gap (G3) GA was used to obtain the optimized values of the JMA parameters, i.e., the activation energy, pre-exponential factor, and exponent in the nonisothermal JMA equation. The GA based determination of all three JMA equation parameters resulted in better agreement between the calculated and the experimentally determined austenite phase fractions than was previously achieved.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. J.W. Elmer, T.A. Palmer, W. Zhang, B. Wood, and T. DebRoy: Acta Mater., 2003, vol. 51, pp. 3333–49.10.1016/S1359-6454(03)00049-1 ↗
2. S.K. Nath, S. Ray, and V.N.S. Mathur: Iron Steel Inst. Jpn., 1994, vol. 34, pp. 191–97.10.2355/isijinternational.34.191 ↗
3. A. De and T. DebRoy: J. Phys. D: Appl. Phys., 2004, vol. 37, pp. 140–50.10.1088/0022-3727/37/1/023 ↗
4. A. Kumar, W. Zhang, C.-H. Kim, and T. DebRoy: 7th Int. Sem. on Numerical Analysis of Weldability, Graz, Austria, Sept. 29–Oct. 1, 2003, H. Cerjak, H.K.D.H. Bhadesia, and E. Kozeschnik, eds., Technical University of Graz Press, Graz, Austria, 2004, pp. 1–24.
5. A. Kumar and T. DebRoy: Int. J. Heat Mass Transfer, 2004, vol. 47, pp. 5793–806.10.1016/j.ijheatmasstransfer.2004.06.038 ↗
6. D.E. Goldberg: GA in Search, Optimization and Machine Learning, Addison-Wesley, Boston, MA, 1989.
7. Handbook of Evolutionary Computations, T. Back, D.B. Fogel, and Z. Michalewicz, eds., IOP Publishing Ltd., Oxford University Press, Oxford, United Kingdom, 2000.
8. W. Zhang, J.W. Elmer, and T. DebRoy: Mater. Sci. Eng. A, 2002, vol. 333, pp. 321–35.10.1016/S0921-5093(01)01857-3 ↗
9. Z. Yang, J.W. Elmer, J. Wong, and T. DebRoy: Welding J., 2000, vol. 79, pp. 97s-112s.
10. A. De and T. DebRoy: J. Appl. Phys., 2004, vol. 95, pp. 5230–40.10.1063/1.1695593 ↗
11. S. Mishra and T. DebRoy: Acta Mater., 2004, vol. 52, pp. 1183–92.10.1016/j.actamat.2003.11.003 ↗
12. Z. Yang, S. Sista, J.W. Elmer, and T. DebRoy: Acta Mater., 2000, vol. 48, pp. 4813–25.10.1016/S1359-6454(00)00279-2 ↗
13. X. He, P.W. Fuerschbach, and T. DebRoy: J. Appl. Phys., 2003, vol. 94, pp. 6949–58.10.1063/1.1622118 ↗
14. A. Kumar and T. DebRoy: J. Appl. Phys., 2003, vol. 94, pp. 1267–77.10.1063/1.1587006 ↗
15. S.A. David, R. Trivedi, M.E. Eshelman, J.M. Vitek, S.S. Babu, T. Hong, and T. DebRoy: J. Appl. Phys., 2003, vol. 93, pp. 4885–95.10.1063/1.1531814 ↗
16. W. Zhang, G.G. Roy, J.W. Elmer, and T. DebRoy: J. Appl. Phys., 2003, vol. 93, pp. 3022–33.10.1063/1.1540744 ↗
17. X. He, P.W. Fuerschbach, and T. DebRoy: J. Phys. D: Appl. Phys., 2003, vol. 36, pp. 1388–98.10.1088/0022-3727/36/12/306 ↗
18. T. Hong and T. DebRoy: Metall. Mater. Trans. B, 2003, vol. 34B, pp. 267–69.10.1007/s11663-003-0013-1 ↗
19. W. Pitscheneder, T. DebRoy, K. Mundra, and R. Ebner: Welding J., 1996, vol. 75, pp. 71s-80s.
20. K. Mundra, T. DebRoy, and K.M. Kelkar: Num. Heat Transfer A, 1996, vol. 29, pp. 115–29.10.1080/10407789608913782 ↗
21. W. Zhang, J.W. Elmer, and T. DebRoy: Scripta Mater., 2002, vol. 46, pp. 753–57.10.1016/S1359-6462(02)00040-4 ↗
22. K. Deb, A. Anand, and D. Joshi: KanGAL Report No. 2002003, Indian Institute of Technology, Kanpur, India, 2002.
23. K. Deb: KanGAL Report No. 2003003, Indian Institute of Technology, Kanpur, India, 2003.
24. S.V. Patankar: Numerical Heat Transfer and Fluid Flow, Hemisphere, New York, NY, 1980.
25. J.W. Elmer, J. Wong, and T. Ressler: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1175–88.10.1007/s11661-001-0127-5 ↗
26. J.W. Christian: The Theory of Transformations in Metals and Alloys, 3rd ed., Pergamon, Boston, MA, 2002.
27. J.M. Criado and A. Ortega: Acta Metall., 1987, vol. 35, pp. 1715–21.10.1016/0001-6160(87)90117-9 ↗
28. Unpublished data from J.W. Elmer, T.A. Palmer, S.S. Babu, and E.D. Specht: Lawrence Livermore National Laboratory, Livermore, CA, Feb. 2004.