journal article·2026-02

Severe, Moderate, and Mild Wear Performance of Deep Cryogenically Treated D3 Tool Steel Against Al2O3, 100Cr6, and 316 Stainless Steel Balls

Alican Boztepe, Gokhan Ozer, Ridvan Gecu

Publisher page

Abstract

This study investigates the effects of severe, moderate, and mild wear behavior of cryogenically treated and double-tempered AISI D3 cold-work tool steel under varying wear conditions. Cryogenic treatment was performed at − 196 °C for 18 hours and each tempering step was carried out at 250 °C for 2 hours. Three different balls—Al2O3, 100Cr6, and 316 stainless steel—and three different loads—5, 10, and 15 N—were used in dry sliding tests. Microstructural and tribological analyses were conducted using FESEM and EDS techniques. The cryogenic treatment facilitated the transformation of retained austenite into martensite, while double tempering promoted the formation of M7C3 and M23C6-type carbides. Regardless of the ball used, increasing the load increased the wear losses due to the enhanced contact pressure. The Al2O3 ball resulted in abrasive wear, while 316 stainless steel caused extremely high galling between tribopairs. Abrasive, adhesive, and oxidative wear occurred in the D3 tool steel samples slid against 100Cr6 steel, providing a mild wear regime, although it was chosen to simulate moderate wear conditions. Considering the wear losses of both cryogenically treated AISI D3 tool steel and its counterparts used, the 100Cr6 ball resulted in the lowest wear losses.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. P. Jurči and I. Dlouhý: Materials, 2024, vol. 17, p. 548. https://doi.org/10.3390/ma17030548.10.3390/ma17030548 ↗
2. Y. Arslan, I. Uygur, and A. Jazdzewska: J. Manuf. Sci. Eng. Trans. ASME, 2015, vol. 137, p. 034501. https://doi.org/10.1115/1.4029567.10.1115/1.4029567 ↗
3. X. He, X.Y. Lü, Z.W. Wu, S.H. Li, Q.L. Yong, J.X. Liang, J. Su, L.X. Zhou, J. Li, and K.Y. Zhao: J. Iron. Steel Res. Int., 2021, vol. 28, pp. 629–40. https://doi.org/10.1007/s42243-020-00514-w.10.1007/s42243-020-00514-w ↗
4. D.M. Lal, S. Renganarayanan, and A. Kalanidhi: Cryogenics (Guildf), 2001, vol. 41, pp. 149–55.10.1016/S0011-2275(01)00065-0 ↗
5. J. Santhakumar and U. Mohammed Iqbal: Materials, 2019, vol. 12, p. 1335. https://doi.org/10.3390/ma12081335.10.3390/ma12081335 ↗
6. S. Kheirandish, H. Saghafian, J. Hedjazi, and M. Momeni: J. Iron. Steel Res. Int., 2010, vol. 17, pp. 40–45. https://doi.org/10.1016/S1006-706X(10)60140-9.10.1016/S1006-706X(10)60140-9 ↗
7. S.A. Elghazaly: Int. J. Mater. Technol. Innov., 2023, vol. 3, pp. 64–73. https://doi.org/10.21608/ijmti.2023.198375.1080.10.21608/ijmti.2023.198375.1080 ↗
8. R. Bahadur Singh and D. Kumar: Int. J. Recent Sci. Res., 2019, vol. 10, pp. 32540–45. https://doi.org/10.24327/ijrsr.2019.1005.3493.10.24327/ijrsr.2019.1005.3493 ↗
9. S. Orhan, A.O. Er, N. Camuşcu, and E. Aslan: NDT E Int., 2007, vol. 40, pp. 121–26. https://doi.org/10.1016/j.ndteint.2006.09.006.10.1016/j.ndteint.2006.09.006 ↗
10. P. Jovicevic-Klug and B. Podgornik: J. Mater. Res. Technol., 2020, vol. 9, pp. 13118–27. https://doi.org/10.1016/j.jmrt.2020.09.071.10.1016/j.jmrt.2020.09.071 ↗
11. P. Jovičević-Klug, M. Sedlaček, M. Jovičević-Klug, and B. Podgornik: Materials, 2021, vol. 14, p. 7561. https://doi.org/10.3390/ma14247561.10.3390/ma14247561 ↗
12. D.H. Li, W.C. He, X. Zhang, M.G. Xiao, S.H. Li, K.Y. Zhao, and M.S. Yang: J. Iron. Steel Res. Int., 2021, vol. 28, pp. 370–82. https://doi.org/10.1007/s42243-020-00527-5.10.1007/s42243-020-00527-5 ↗
13. H.C. Patel, G. Deheri, H.S. Patel, and S.M. Mehta: Proceedings of International Conference on Advances in Tribology and Engineering Systems, Springer, New Delhi, 2014.10.1007/978-81-322-1656-8 ↗
14. S. Kumar, M. Nagaraj, A. Bongale, and N.K. Khedkar: Int. J. Mater. Eng. Innov., 2019, vol. 10, pp. 98–113.10.1504/IJMATEI.2019.099789 ↗
15. P. Jovičević-Klug, T. Kranjec, M. Jovičević-Klug, T. Kosec, and B. Podgornik: Materials, 2021, vol. 14, p. 6357. https://doi.org/10.3390/ma14216357.10.3390/ma14216357 ↗
16. D.M. Lal, S. Renganarayanan, and A. Kalanidhi: Cryogenic treatment to augment wear resistance of tool and die steels.
17. R. Gecu: Mater. Chem. Phys., 2022, vol. 292, p. 136802. https://doi.org/10.1016/j.matchemphys.2022.126802.10.1016/j.matchemphys.2022.126802 ↗
18. A. Boztepe and R. Gecu: J. Tribol., 2025, vol. 147, p. 064201. https://doi.org/10.1115/1.4067045.10.1115/1.4067045 ↗
19. A. Boztepe and R. Gecü: Tribol. Trans., 2025, https://doi.org/10.1080/10402004.2025.2462566.10.1080/10402004.2025.2462566 ↗
20. T. Nykiel and T. Hryniewicz: J. Mater. Eng. Perform., 2014, vol. 23, pp. 2050–54. https://doi.org/10.1007/s11665-014-0979-7.10.1007/s11665-014-0979-7 ↗
21. V. Yarasu, P. Jurci, P. Gogola, B. Podgornik, and M. Sedlaček: Wear, 2023, vol. 532–533, p. 205107. https://doi.org/10.1016/j.wear.2023.205107.10.1016/j.wear.2023.205107 ↗
22. V. Yarasu, P. Jurci, and J. Hornik: Tribol. Int., 2024, vol. 195, p. 109564. https://doi.org/10.1016/j.triboint.2024.109564.10.1016/j.triboint.2024.109564 ↗
23. V.M. Desai, C.M. Rao, T.H. Kosel, and N.F. Fiore: Wear, 1984, vol. 94, pp. 89–101.10.1016/0043-1648(84)90168-6 ↗
24. H. Shi, S. Du, C. Sun, C. Song, Z. Yang, and Y. Zhang: Materials, 2018, vol. 12, p. 45. https://doi.org/10.3390/ma12010045.10.3390/ma12010045 ↗
25. A. John, H. Bąkowski, and B. Śleziak: Multiscale Multidiscip. Model. Exp. Des., 2024, vol. 7, pp. 4965–77. https://doi.org/10.1007/s41939-024-00570-9.10.1007/s41939-024-00570-9 ↗
26. F. Çavdar: J. Mater. Eng. Perform., 2024, vol. 33, pp. 8354–71. https://doi.org/10.1007/s11665-023-08537-6.10.1007/s11665-023-08537-6 ↗
27. J. Stella, M.R. Cruz, and J. López: Tribol. Lett., 2013, vol. 51, pp. 49–56. https://doi.org/10.1007/s11249-013-0144-8.10.1007/s11249-013-0144-8 ↗
28. D. Das, R. Sarkar, A.K. Dutta, and K.K. Ray: Mater. Sci. Eng. A, 2010, vol. 528, pp. 589–603. https://doi.org/10.1016/j.msea.2010.09.057.10.1016/j.msea.2010.09.057 ↗
29. K. Amini, S. Nategh, and A. Shafyei: Mater. Des., 2010, vol. 31, pp. 4666–75. https://doi.org/10.1016/j.matdes.2010.05.028.10.1016/j.matdes.2010.05.028 ↗
30. M. Priyadarshini, A. Behera, and C.K. Biswas: J. Braz. Soc. Mech. Sci. Eng., 2020, vol. 42, p. 212. https://doi.org/10.1007/s40430-020-02298-2.10.1007/s40430-020-02298-2 ↗
31. G.W. Stachowiak and A.W. Batchelor: Eng. Tribol., 2013, https://doi.org/10.1016/C2011-0-07515-4.10.1016/C2011-0-07515-4 ↗
32. S. Kumar, S. RanjanMaity, and L. Patnaik: Mater. Today Proc., 2021, vol. 44, pp. 949–54.10.1016/j.matpr.2020.11.004 ↗