Effect of Solutionization Temperature on the Interfacial Microstructure of a Hot Roll Bonded Alloy 690/Carbon Steel Clad Steel Plate
Source abstract
Abstract
Abstract Fabrication of a Ni-based superalloy Alloy 690 cladded ASTM SA516 GR60 carbon steel (GR60) clad steel plate was carried out through vacuum hot roll bonding at 1323 K for the first time. The as-rolled clad plate showed excellent metallurgical bonding at the joining interface, however, a precipitation zone within the Alloy 690 layer containing Cr23C6 carbides was observed, which is detrimental to the intergranular corrosion resistance. A comprehensive approach integrating thermodynamic calculations and numerical simulations of long-range diffusion of alloying elements was employed to optimize the post rolling solutionization heat treatment temperature. Thermodynamic calculations predicted the possibility of reduction in Cr-carbide amount on solutionization in the temperature range of 1373 K to 1573 K. Guided by these calculations, as-rolled specimen was solutionized at 1373 K for 4 hours, however, the width of the Cr23C6 carbide precipitation zone was found to increase instead of decreasing due to enhanced Cr and C diffusion. On the other hand, solutionization at 1473 K for 4 hours resulted in a substantial reduction in Cr23C6 precipitates on Alloy 690 side. Formation of a thin stabilized γ-FCC (γ s) was noticed on the GR60 side after solutionization at 1373 K due to net influx of Ni from Alloy 690 alloy, which separates the original joining interface from the bulk GR60. The width of this γ s region further increased after 1473 K-4 hours solutionization due to enrichment of Ni within GR60 layer. Overall, a higher solutionization temperature (1473 K) was found to be more effective to reduce the Cr-carbide amount in Alloy 690 cladded GR60 plates than that usually employed 1373 K for monolithic Alloy 690 plate.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metallurgy and Material Forming · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. R.E. Gold, D.L. Harrod, R.G. Aspden, and A.J. Baum: Westinghouse Electric Corporation NP-6997-SD, Research Project S408-6, 1990. https://www.epri.com/research/products/NP-6997-SD .
2. P. Sengupta, C.P. Kaushik, R.K. Mishra, and G.B. Kale: J. Am. Ceram. Soc., 2007, vol. 90(10), pp. 3057–62. https://doi.org/10.1111/j.1551-2916.2007.01853.x.10.1111/j.1551-2916.2007.01853.x ↗
3. T. Yonezawa: Compr. Nucl. Mater., 2012, vol. 2, pp. 233–66. https://doi.org/10.1016/B978-0-08-056033-5.00016-1.10.1016/B978-0-08-056033-5.00016-1 ↗
4. J. Hickling: EPRI, Palo Alto, CA, 2009, p. 1019086. https://www.epri.com/research/products/1019086.
5. Y. Jing, Y. Qin, X. Zang, and Y. Li: J. Mater. Process. Technol., 2014, vol. 214(8), pp. 1686–95. https://doi.org/10.1016/j.jmatprotec.2014.03.019.10.1016/j.jmatprotec.2014.03.019 ↗
6. Y. Jing, Y. Qin, X. Zang, Q. Shang, and H. Song: J. Alloys Compd., 2014, vol. 617, pp. 688–98. https://doi.org/10.1016/j.jallcom.2014.07.186.10.1016/j.jallcom.2014.07.186 ↗
7. B.X. Liu, S. Wang, C.X. Chen, W. Fang, J.H. Feng, X. Zhang, and F.X. Yin: Appl. Surf. Sci., 2019, vol. 463, pp. 121–31. https://doi.org/10.1016/j.apsusc.2018.08.221.10.1016/j.apsusc.2018.08.221 ↗
8. C.E. Stevens and R.W. Ross: J. Mater. Energy Syst., 1986, vol. 8(1), pp. 7–16. https://doi.org/10.1007/BF02833455.10.1007/BF02833455 ↗
9. L. Gupta, N. Keskar, B.C. Maji, R.N. Singh, and M. Krishnan: Metall. Mater. Trans. A, 2024, vol. 55(11), pp. 4354–72. https://doi.org/10.1007/s11661-024-07547-w.10.1007/s11661-024-07547-w ↗
10. S. Nishida, M. Toshio, and W. Tsunemi, JFE Steel Corporation, JFE Technical Report No. 5, 2004, pp. 1–9.
11. I.A. Segura, L.E. Murr, C.A. Terrazas, D. Bermudez, J. Mireles, V.S.V. Injeti, K. Li, B. Yu, R.D.K. Misra, and R.B. Wicker: J. Mater. Sci. Technol., 2019, vol. 35, pp. 351–67. https://doi.org/10.1016/j.jmst.2018.09.059.10.1016/j.jmst.2018.09.059 ↗
12. T. Baidridge, G. Poling, E. Foroozmehr, R. Kovacevic, T. Metz, V. Kadekar, and M.C. Gupta: Opt. Lasers Eng., 2013, vol. 51(2), pp. 180–84. https://doi.org/10.1016/j.optlaseng.2012.08.006.10.1016/j.optlaseng.2012.08.006 ↗
13. B. López, I. Gutiérrez, and J.J. Urcola: Microstructural analysis of steel-nickel alloy clad interfaces. Mater. Sci. Technol., 1996, vol. 12(1), pp. 45–55. https://doi.org/10.1179/mst.1996.12.1.45.10.1179/mst.1996.12.1.45 ↗
14. M. Consonni, F. Maggioni, and F. Brioschi: ICONE14-89434, 2006, pp. 539–45. https://doi.org/10.1115/ICONE14-89434.10.1115/ICONE14-89434 ↗
15. B.X. Liu, Q. An, F.X. Yin, S. Wang, and C.X. Chen: J. Mater. Sci., 2019, vol. 54, pp. 11357–77. https://doi.org/10.1007/s10853-019-03581-x.10.1007/s10853-019-03581-x ↗
16. X. Wu and Y. Zhu: Mater. Res. Lett., 2017, vol. 5, pp. 527–32. https://doi.org/10.1080/21663831.2017.1343208.10.1080/21663831.2017.1343208 ↗
17. S. Tachibana, Y. Kuronuma, T. Yokota, K. Yamada, Y. Moriya, and C. Kami: Corros. Sci., 2015, vol. 99, pp. 125–33. https://doi.org/10.1016/j.corsci.2015.06.028.10.1016/j.corsci.2015.06.028 ↗
18. American Society of Testing Materials. ASTM A516/A516M-10: Standard specification for pressure vessel plates, carbon steel, for moderate—and lower- temperature service.
19. American Society of Testing Materials. ASTM B690-22: Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy Seamless Pipe and Tube.
20. S. Guo, D. Li, H. Pen, Q. Guo, and J. Hu: J. Nucl. Mater., 2011, vol. 410(1–3), pp. 52–58. https://doi.org/10.1016/j.jnucmat.2010.12.309.10.1016/j.jnucmat.2010.12.309 ↗
21. G.E. Dieter: Mechanical Metallurgy, 3rd ed. McGraw Hill Education (India) Private Limited, New Delhi, 2013, pp. 586–615.
22. E. Kozeschnik and B. Buchmayr: Math. Modell. Weld Phenom., 2001, vol. 5, pp. 349–61.
23. E. Kozeschnik: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2575–82. https://doi.org/10.1007/s11661-999-0296-1.10.1007/s11661-999-0296-1 ↗
24. M. Casales, V.M. Salinas-Bravo, A. Martinez-Villafañe, and J.G. Gonzalez-Rodriguez: Mater. Sci. Eng. A, 2002, vol. 332(1–2), pp. 223–30. https://doi.org/10.1016/S0921-5093(01)01747-6.10.1016/S0921-5093(01)01747-6 ↗
25. Y.S. Lim, J.S. Kim, H.P. Kim, and H.D. Cho: J. Nucl. Mater., 2004, vol. 335(1), pp. 108–14. https://doi.org/10.1016/j.jnucmat.2004.07.038.10.1016/j.jnucmat.2004.07.038 ↗
26. H.U. Hong, B.S. Rho, and S.W. Nam: Mater. Sci. Eng. A, 2001, vol. 318(1–2), pp. 285–92. https://doi.org/10.1016/S0921-5093(01)01254-0.10.1016/S0921-5093(01)01254-0 ↗
27. M. Abbasi, I. Park, H. Park, and R. Ayer: SSRN Electron. J., 2022, https://doi.org/10.2139/ssrn.4010399.10.2139/ssrn.4010399 ↗
28. A.L. Schaeffler: Met. Progress, 1949, vol. 56(l1), p. 680.
29. F. Farias, I. Alvarez-Armas, and A.F. Armas: Int. J. Fatigue, 2020, vol. 140, pp. 1–8. https://doi.org/10.1016/j.ijfatigue.2020.105809.10.1016/j.ijfatigue.2020.105809 ↗
30. P. Cavaliere, A. Silvello, N. Cinca, H. Canales, S. Dosta, I. Garcia Cano, and J.M. Guilemany: Surf. Coat. Technol., 2017, vol. 324, pp. 390–402. https://doi.org/10.1016/j.surfcoat.2017.06.006.10.1016/j.surfcoat.2017.06.006 ↗