journal article·2025-08Open access

Key Considerations of Electro-thermal Mechanical Testing in Ni-Base Superalloy Phase Transformations

N. D’Souza, B. Roebuck, I. M. Edmonds, G. D. West, D. M. Collins

Abstract

Abstract Electro-thermal mechanical testing (ETMT) with direct current and Joule heating was used to study the dissolution and formation of $$\gamma '$$ precipitates in miniaturised samples of the single crystal nickel-base superalloys, CMSX4 and CMSX10N. Alloys were subjected to heating and cooling cycles with resistivity simultaneously measured to infer $$\gamma \leftrightarrow \gamma '$$ phase transformations. Temperature-resolved resistivity measurements exhibit notable variations between samples; however, when normalized, the resistivity changes become systematic, with trends suitable to infer phase transformation behaviour. Specifically, dissolution and precipitation behaviour of the $$\gamma '$$ phase with respect to heating or cooling rates can be determined. The ETMT measured $$\gamma '$$ solvus is lower compared with the calorimetric/thermodynamic value and approaches the latter, when the resistivity values exceed a threshold value, which is temperature dependent. The differences in the resistivity curves cannot be explained by the range in $$\gamma '$$ size distribution within the specimens; rather, the difference becomes prominent above a threshold current density, which occurs above a given temperature. Like in the case of dissolution, the nucleation and precipitation of $$\gamma '$$ is dependent on the normalized resistivity, but independent of stress, if cooling occurs under restraints in case of the latter. A greater $$\gamma '$$ solvus corresponds to an increased nucleation temperature, implying a varying undercooling for nucleation when calculated with respect to the thermodynamic solvus. When stress develops during cooling, it increases rapidly above a critical $$\gamma '$$ mole-fraction when precipitation hardening becomes prominent. Given these features are endemic to ETMT, some guidelines are offered for use of ETMT tests in specific applications.
Source: crossref · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · Metallurgical and Alloy Processes · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. B. Roebuck, D. Cox, and R. Reed: 10th Int Conf on Superalloys 2004, TMS, Warrendale, PA, 2004. pp. 523–28.10.7449/2004/Superalloys_2004_523_528 ↗
2. J.F.S. Markanday, N. D’Souza, N.L. Church, J.R. Miller, J.J.C. Pitchforth, L.D. Connor, S. Michalik, B. Roebuck, N.G. Jones, K.A. Christofidou, and H.J. Stone: 14th Int. Conf. on Superalloys 2004, TMS, Warrendale, PA, 2024, pp. 822–35.10.1007/978-3-031-63937-1_77 ↗
3. Y.T. Tang, C. Panwisawas, B.M. Jenkins, J. Liu, Z. Shen, E. Salvati, Y. Gong, J.N. Ghoussoub, S. Michalik, B. Roebuck, P.A.J. Bagot, S. Lozano-Perez, C.R. Grovenor, M.P. Moody, A.M. Korsunsky, D.M. Collins, and R.C. Reed: Addit. Manuf., 2023, vol. 62, p. 103389
4. N. D’Souza, B. Roebuck, D.M. Collins, G.D. West, and C. Panwisawas: Mater. Sci. Eng. A, 2020, vol. 773, p. 138862.10.1016/j.msea.2019.138862 ↗
5. Y.T. Tang, N. D’Souza, B. Roebuck, P. Karamched, C. Panwisawas, and D.M. Collins: Acta Mater., 2021, vol. 203, p. 116408.
6. I.E. Benrabah, G. Altinkurt, M. Fèvre, M. Dehmas, B. Denand, F. Fossard, J.S. Mérot, G. Geandier, D. Locq, and M. Perrut: J. Alloys Compd., 2020, vol. 825, p. 154108.10.1016/j.jallcom.2020.154108 ↗
7. D.C. Cox, B. Roebuck, and R.C. Reed: Mater. Sci. Technol., 2003, vol. 19, pp. 440–46.10.1179/026708303225010731 ↗
8. S.J. Perry, N. D’Souza, D.M. Collins, B. Roebuck, and H.B. Dong: Metall. Mater. Trans. A, 2023, vol. 54, pp. 1582–96.10.1007/s11661-022-06861-5 ↗
9. N. D’Souza, M.C. Hardy, B. Roebuck, W. Lei, G.D. West, and D.M. Collins: Metall. Mater. Trans. A, 2022, vol. 53, pp. 2480–95.10.1007/s11661-022-06680-8 ↗
10. S. Utada, R. Sasaki, R.C. Reed, and Y.T. Tang, Metall. Mater. Trans. A, 2023, vol. 54, pp. 1549–67.10.1007/s11661-022-06924-7 ↗
11. S. Sulzer, E. Alabort, A. Nemeth, B. Roebuck, and R.C. Reed, Metall. Mater. Trans. A, 2018, vol. 49, pp. 4214–35.10.1007/s11661-018-4673-5 ↗
12. Z. Wang, X. Huang, X. Ye, C. Zhao, J. Hu, Z. Li, X. Liu, and X. Li: J. Alloys Compd., 2023, vol. 945, p. 169321.10.1016/j.jallcom.2023.169321 ↗
13. Y.T. Tang, C. Schwalbe, M. Futoma, B. Roebuck, S. Utada, and R.C. Reed: Metall. Mater. Trans. A, 2023, vol. 54, pp. 1568–81.10.1007/s11661-022-06869-x ↗
14. R. Sasaki, S. Utada, Y.T. Tang, C.A. Nunes, and R.C. Reed: 14th Int. Conf. on Superalloys 2024, TMS, Warrendale, PA, 2024, pp. 379–39.10.1007/978-3-031-63937-1_36 ↗
15. T. Koppenaal, and C. Simcoe: Trans. Metall. Soc. AIME, 1963, vol. 227, pp. 615–18.
16. Y. Onodera, and K.I. Hirano: J. Mater. Sci., 1976, vol. 11, pp. 809–16.10.1007/BF00542295 ↗
17. A. Nicolay, J.M. Franchet, J. Cormier, R.E. Loge, G. Fiorucci, J. Fausty, M.V.D. Meer, and N. Bozzolo: Metall. Mater. Trans. A, 2021, vol. 52, pp. 4572–96.10.1007/s11661-021-06411-5 ↗
18. H. Conrad: Mater. Sci. Eng. A, 2000, vol. 287, pp. 227–37.10.1016/S0921-5093(00)00780-2 ↗
19. T. Grosdidier, A. Hazotte, and A. Simon: Mater. Sci. Eng. A, 1998, vol. 256, pp. 183–96.10.1016/S0921-5093(98)00795-3 ↗
20. J. Cormier, X. Milhet, J.L. Champion, and J. Mendez: Adv. Eng. Mater., 2008, vol. 10, pp. 56–61.10.1002/adem.200700248 ↗
21. R. Giraud, Z. Hervier, J. Cormier, G. Saint-Martin, F. Hamon, X. Milhet, and J. Mendez: Metall. Mater. Trans. A, 2013, vol. 44, pp. 131–46.10.1007/s11661-012-1397-9 ↗
22. N. D’Souza, R. Beanland, C. Hayward, and H.B. Dong: Acta Mater., 2011, vol. 59, pp. 1003–13.10.1016/j.actamat.2010.10.031 ↗
23. N. D’Souza, and H.B. Dong: Int. J. Cast Met. Res., 2009, vol. 22, pp. 58–61.10.1179/136404609X367335 ↗
24. C. Panwisawas, J.C. Gebellin, and R.C. Reed: Mater. Sci. Technol., 2013, vol. 29, pp. 843–53.10.1179/1743284712Y.0000000197 ↗
25. B. Roebuck, M. Brooks, and A. Pearce: Good Practice Guide for Miniature ETMT Tests, NPL Good Practice Guide No. 137, 2016.
26. H.B. Dong, and J.D. Hunt: J. Therm. Anal. Calorim., 2001, vol. 64, pp. 167–76.10.1023/A:1011589013639 ↗
27. N. D’Souza, M. Lekstrom, H.J. Dai, B.A. Shollock, and H.B. Dong: Mater. Sci. Technol., 2007, vol. 23, pp. 1086–93.
28. G.U. Sente Software: JMatProTM, Ni module (version 2.0), 2002.
29. P.L. Rossiter: The Electrical Resistivity of Metals and Alloys, Cambridge University Press, Cambridge, 2010.
30. B. Roebuck, D.C. Cox, and R.C. Reed, Scripta Mater., 2001, vol. 44, pp. 917–21.10.1016/S1359-6462(00)00662-X ↗
31. A. Koko, W. Bond, R. Simpson, M. Lodeiro, A. Mendiata, and G. Sutton: 10th Int. Conf. on Advances in Materials, Manufacturing and Repair for Power Plants, Bonita Springs, FL, 2024, pp. 449–60.10.31399/asm.cp.am-epri-2024p0449 ↗
32. G. Sutton, A. Greenen, B. Roebuck, and G. Machin: Mater. Sci. Technol., 2019, vol. 30, pp. 1–11.